Whirlpool Awod 049 Programme Chart Manual

							GB AWO/D 049 PROGRAMME CHART❉: optional / Yes : dosing required1)
For improved garment care, spin speed is restricted to 400 rpm in this programme.
5019 301 10448
Whirlpool is a registered trademark of Whirlpool USA
Programme
Care
Labels
Type of wash/Notes
- for temperature selection, respect the manufacturer’s recommendations on the care label
Max 
Load
kg
Detergents and additives
Special options
Spin
Speed
rpm
Pre-
wash
Main 
Was h
Softener
Spin
speed
reduction
500 rpm
Rinse hold
Cotton with prewash
95 °C
Heavily soiled, long wearing and temperature stable textiles in cotton and linen (bed linen, table 
linen, underwear, shirts etc.).5.0 Yes Yes
❉❉ ❉
1000
Cotton
40 - 60 - 95 °C
 
Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. made of cotton 
and linen.5.0 — Yes
❉❉ ❉
1000
Synthetics with prewash
60 °C
Heavily soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide (Perlon, 
Nylon) or blends with cotton.2.5 Yes Yes
❉❉ ❉
1000
Synthetics
30 - 40 - 60 °C
 
 
Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), polyamide 
(Perlon, Nylon) or blends with cotton.2.5 — Yes
❉❉ ❉
1000
Delicates30 °C
 
Curtains and delicate clothing, dresses skirts, shirts and blouses. 1.5 — Yes
❉❉ ❉
1000
Quick wash
30 °C
Shortly worn outer clothing made of cotton, polyester, polyamide and blends with cotton. 3.0 — Yes
❉❉ ❉
1000
Wo o lCold - 40 °C
Only woollens with a felt-free finish, labelled with the woolmark and identified as machine 
washable. 
If you select “Rinse Hold” do not leave items to soak for too long. 1.0 — Yes
❉❉ ❉
1000
Handwash
30 -
 40 °C
Textiles made of linen, silk, wool and viscose marked as “handwashable”.
If you select “Rinse Hold” do not leave items to soak for too long. A very gentle spin is used in this 
programme.1.0 — Yes
❉
—
❉
400
1)
Rinse & Spin —Same as the last rinse and the final spin in the “Cotton” programme.
5.0 — —
❉❉ ❉
1000
Spin —In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme.
5.0 — — —
❉
—1000
Gentle Spin —In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme.
1.0 — — —
❉
—1000
Drain —Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”.
—— — — — — —
A. “Door open” indication
This washing machine is equipped with 
automatic safety functions which 
detect and diagnose faults at an early 
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indicationE. Programme selector
F. “Start/Pause” button
G. Programme sequence indicator
H. “Reset” button
DGC
F
H
EB A
 
						

							5019 301 10448
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as 
described in your Instructions for Use. Close the 
door and turn the 
programme selector to the 
desired programme and temperature. The indication 
lamp next to the 
“Start /Pause” button flashes.
Push the button(s) of any option(s) desired - the 
respective indication lamp lights up.
When the combination of programme and additional 
option(s) is not possible, the indication lights switch off 
automatically. Unsuitable combinations of options are 
deselected automatically.
“Spin speed reduction 500 rpm” button
 Reduces the predetermined automatic maximum 
spin speed to treat your laundry more gently.“Rinse hold” button
 The laundry remains in the last rinse water 
without progressing to the final spin cycle to avoid 
creasing and prevent colours from changing.
 This option is particularly recommended for the 
programmes “Synthetics” and “Delicates”.
 This function is particularly useful if you want to 
postpone spinning to a later time, or if you want 
to drain only.
Note: The programme stops to “Rinse hold” at 
the time the “Rinse hold” light in the programme 
sequence indicator is on. The indication lamp 
next to the 
“Start/Pause” button flashes.
Terminate the “Rinse hold” option:
 Press the 
“Start/Pause” button; the 
programme will terminate automatically with the 
final spin cycle for the present wash programme.
 If you do not wish to spin the clothes, turn the 
programme selector knob to the “Drain” 
programme and press the 
“Start/Pause” button.CONSUMPTION DATA
Programme
Temperature 
(°C)
Load
(kg)
Wa t e r
(l)
Energy
(kWh)
Approx. Programme
Duration
(hours : minutes)
Cotton 95 5.0 49
**1.90 2:00
Cotton
***60 5.0 44 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Synthetics 60 2.5 50
**0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Quick wash 30 3.0 40 0.40 0:30
Delicate 30 1.5 50 0.50 0:45
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Handwash 30 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption 
data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, 
the load and the type of wash.
**To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains 
the water out.
***Reference Programme for Energy Label.ADD DETERGENTS, CLOSE THE DOOR 
AND SELECT THE PROGRAMMESELECT ANY DESIRED OPTION
Open the tap and press the 
“Start/Pause” button. 
The indication lamp next to the 
“Start/Pause” 
button lights up. The programme sequence indicator 
shows the current programme phase, running from 
left to right through Wash, Rinse, Spin/Drain.
When the programme phase is finished, the 
corresponding indication goes out.
Before starting and after end of a programme, the 
lamp lights to show that the door can be opened. As 
long as a wash programme is running, the door 
remains locked and must on no account be forced 
open. In case you have an urgent need to open it 
during a running programme, refer to “Cancel 
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused 
by a fault in an electrical component. Refer to the 
“Troubleshooting Guide” in your “Instructions for 
Use”; if the fault persists, contact our After Sales 
Service.
“Water tap closed”
The appliance has no or insufficient water supply. 
Open the water tap; if the indication still lights up, 
refer to the “Troubleshooting Guide” in the 
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the 
drain hose is kinked or the filter must be cleaned; in 
the latter case refer to the Instructions for Use 
(“Removing the Filter”). All the lights of the programme sequence 
indicator are off, and the “Door open” 
indication lights up.
1. Turn the programme selector to the “Off/O” 
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the 
“Start/Pause” button to pause the 
programme. The light flashes.
2. Select the new programme (with temperature), 
any options and another spin speed if you want.
3. Press the 
“Start/Pause” button again. The new 
programme continues at the same position 
where the previous programme was interrupted. 
Do not add detergent for this programme.
The 
“Reset” button cancels a programme before 
the end.
Press the 
“Reset” button for at least 3 
seconds. Any existing water is drained out 
before the door can be opened.PROGRAMME START“DOOR OPEN” INDICATIONRED INDICATIONS
PROGRAMME ENDCHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME STARTCANCEL (RESET) A RUNNING 
PROGRAMME BEFORE THE END