Whirlpool Awod 041 Programme Chart Manual

							GB AWO/D 041 PROGRAMME CHART
5019 301 10453
Whirlpool is a registered trademark of Whirlpool USA
❉:optional / Yes : dosing required
1)
For improved garment care, spin speed is restricted in these programmes.
2)
Do not use liquid detergent for the main wash when activating the prewash option.
3)
Do not use liquid detergent when activating the Start delay.
Programme
Care
Labels
Max.
Load
kg
Type of wash/Notes
- For temperature selection, respect the manufacturer’s recommendations on the care 
label
Detergents and additives
Special options
Max
Spin
Speed
rpm
Pre-
wash
Main
wash
Softener
Start
delay
3)
Eco
Pre-
wash
Intensive
rinse
Rinse
hold
Va r i a b l e
spin
Cotton
40 - 60 - 95 °C
40 - 60 - 95 °C
 
5.0Normally to heavily soiled bed linen, table linen and underwear, towels, shirts etc. 
made of cotton and linen.
With heavily soiled laundry the additional “Prewash” option can be selected.
❉
Ye s
2)
❉❉❉❉❉❉ ❉
1000
Synthetics30 - 40 - 60 °C
30 - 40 - 60 °C
 
 
2.5Normally soiled blouses, shirts, overalls etc. made of polyester (Diolen, Trevira), 
polyamide (Perlon, Nylon) or blends with cotton.
❉
Ye s
2)
❉❉❉❉❉❉ ❉
1000
Delicates30 - 40 °C
30 - 40 °C
 
1.5 Curtains and delicate clothing, dresses skirts, shirts and blouses.
❉
Ye s
2)
❉❉
—❉
—❉❉
1000
Daily load
40 °C
40 °C
 
3.0 Slightly to normally soiled textiles made of cotton and/or synthetics.
—
Ye s
❉❉
——❉❉ ❉
1000
Quick wash
30 °C
30 °C
3.0Shortly worn outer clothing made of cotton, polyester, polyamide and blends with 
cotton.
—
Ye s
❉❉
—— —❉❉
1000
WoolCold - 40 °C
 - 40 °C
1.0Only woollens, labelled with the Woolmark and identified as machine washable.
If you select “Rinse Hold” do not leave items to soak for too long.
—
Ye s
❉❉
—— —❉❉
1000
Handwash30 - 40 °C
30 - 40 °C
1.0Textiles made of linen, silk, wool and viscose marked as “handwashable”.
If you select “Rinse Hold” do not leave items to soak for too long. A very gentle spin is used 
in this programme.
—
Ye s
❉❉
—— —❉❉
400
1)
Rinse & Spin
—
5.0Same as the last rinse and the final spin in the “Cotton” programme.
——❉❉
——❉❉ ❉
1000
Spin
—
5.0In this programme spinning is intensive. Same as the spin cycle in the “Cotton” programme.
—— —❉
—— — —❉
1000
Gentle Spin
—
1.0In this programme spinning is gentle. Same as the spin cycle in the “Wool” programme.
—— —❉
—— — —❉
1000
Drain
——
Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”.
—— — ——— — — — —
A. “Door open” indication
This washing machine is equipped with 
automatic safety functions which 
detect and diagnose faults at an early 
stage and react appropriately, e.g.:
B. “Service” indication
C. “Water tap closed” indication
D. “Clean pump” indication
E. Programme selector
F. “Start/Pause” button
G. Spin speed selector
H. Programme sequence indicator
and Start delay indicators
I. “Reset” button
J. “Start delay” button
H
E
BA
D C
F
G
J
I
 
						

							5019 301 10453
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as 
described in the chapter “Detergent and Additives” 
in your Instructions for Use.
Close the door and turn the programme selector to the 
desired programme and temperature. The indication 
lamp next to the 
“Start/Pause” button   flashes.
Push the button(s) of any option(s) desired - the 
respective indication lights up.
When the combination of programme and additional 
option(s) is not possible, the indication lights switch 
off automatically. Unsuitable combinations of 
options are deselected automatically.
“Eco” button
 With a modified temperature profile and a slightly 
prolonged washing duration, the optimum 
combination of excellent washing result and even 
lower energy consumption is achieved.
“Prewash” button
 Only for heavily soiled loads (for example sand, 
granular dirt) sensible. Increases the cycle time 
by approximately 15 min.
 Do not use liquid detergent for the main wash 
when activating the Prewash option.
“Intensive rinse” button
 More water is added and rinse cycle is prolonged. This option is particularly suitable for areas with 
very soft water, washing baby linen and helps 
people with allergies.
“Rinse hold” button
 The laundry remains in the last rinse water 
without progressing to the final spin cycle to avoid 
creasing and prevent colours from changing.
 This option is particularly recommended for the 
programmes “Synthetics”, “Daily load” and 
“Delicates”.
 It is particularly useful if you want to postpone 
spinning to a later time, or if you want to drain only.
Note: The programme stops to “Rinse hold” at 
the time the “Rinse hold” light in the programme 
sequence indication is on. The indication lamp 
next to the 
“Start/Pause” button   flashes.
Terminate the “Rinse hold” option :
 Press the 
“Start/Pause” button  ; the 
programme will terminate automatically with the 
final spin cycle for the present wash programme.
 If you do not wish to spin the clothes, turn the 
programme selector knob to the “Drain” programme 
and press the 
“Start/Pause” button  .
“ Variable spin” button
 Every programme has a predefined spin speed.
 Press the button to set another spin speed.
 If spin speed “0” is selected, the final spinning is 
cancelled but intermediate spin peaks remain 
during rinse. The water is drained out only.CONSUMPTION DATA
Programme
Temperature
(°C)
Load
(kg)
Wat e r
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
Cotton 95 5.0 49
*1.90 2:00
Cotton 60 5.0 44 0.95 2:10
Cotton with “Eco”
**60 5.0 44 0.85 2:20
Cotton 40 5.0 44 0.60 2:00
Synthetics 60 2.5 50
*0.70 1:30
Synthetics 40 2.5 45 0.55 1:15
Delicates 30 1.5 50 0.50 0:45
Daily load 40 3.0 45 0.45 1:00
Quick wash 30 3.0 40 0.40 0:30
Wool 40 1.0 55 0.60 0:45
Handwash 40 1.0 45 0.60 0:40
Handwash 30 1.0 45 0.50 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home 
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of  wa s h .
*
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out .
**
Reference Programme for Energy Label.ADD DETERGENTS, CLOSE THE DOOR 
AND SELECT THE PROGRAMMESELECT ANY DESIRED OPTION
The “Start Delay”   allows to run the machine at 
the consumer’s convenience, for example at night 
when electricity is cheaper. Do not use liquid 
detergent when activating the start delay.
 Select programme, temperature and options.
 Press the “Start delay ” button to select the delay 
time by 1, 3, 6, 9 or 12 hours.
 Press the 
“Start/Pause” button  . 
The indication  next to the “Start delay ” button 
flashes and goes off when the programme starts.
 Once having pressed the 
“Start/Pause” button 
, the countdown of the time delay begins. 
When the programme starts, the start delay 
indicator light goes off and is replaced by the 
programme sequence indication.
 After the 
“Start/Pause” button 
 has been 
pressed, the number of hours preselected can be 
reduced by pressing again the “Start delay ” button.
To cancel the “Start delay ”
..before you press the “Start/Pause” button:
 Turn the programme selector to another 
position or press the 
“Reset” button  .
..after having pressed the “Start/Pause” button:
Press the
 “Reset” button   for at least 3 
seconds - the start delay indicator light goes out.
Open the tap and press the 
“Start/Pause” button 
. The indication lamp next to the 
“Start/Pause” 
button   lights up. The programme sequence 
indicator shows the current programme phase, running 
from left to right through Wash, Rinse, Spin/Drain.
When the programme phase is finished, the 
corresponding indication goes out.
Before starting and after end of a programme, the 
lamp lights to show that the door can be opened. As 
long as a wash programme is running, the door 
remains locked and must on no account be forced 
open. In case you have an urgent need to open it 
during a running programme, refer to “Cancel 
(Reset) a running programme before the end”.“Water tap closed”
The appliance has no or insufficient water supply. 
Open the water tap; if the indication still lights up, 
refer to the “Troubleshooting Guide” in the 
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the 
drain hose is kinked or the filter must be cleaned; in 
the latter case refer to the Instructions for Use 
(“Removing the Filter”).
“Service”
Lighting up of the “Service” indication can be caused by 
a fault in an electrical component. Refer to the 
“Troubleshooting Guide” in your Instructions for Use; if 
the fault persists, contact our After Sales Service.
 All the lights of the programme sequence 
indicator are off, and the “Door open” 
indication   lights up.
1. Turn the programme selector to the “Off/O” 
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the 
“Start/Pause” button   to pause 
the programme. The light flashes.
2. Select the new programme (with temperature), 
any options and another spin speed if you want.
3. Press the 
“Start/Pause” button   again. The 
new programme continues at the same position 
where the previous programme was interrupted. 
Do not add detergent for this programme.
The 
“Reset” button   cancels a programme 
before the end.
Press the 
“Reset” button   for at least 3 
seconds. Any existing water is drained out 
before the door can be opened.START DELAYPROGRAMME START“DOOR OPEN” INDICATION
RED INDICATIONSPROGRAMME ENDCHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME STARTCANCEL (RESET) A RUNNING 
PROGRAMME BEFORE THE END