Whirlpool Awm 9100 Programme Chart Manual

							GB AWM 9100  PROGRAMME CHART
5019 301 15169
Whirlpool is a registered trademark of Whirlpool USA
Programme
Care
labels
Type of wash/Notes
Max. 
Load
kg
Detergents and additives
Special Options
Spin
Speed
max
Te m p e r a t u r e
°C 
max
Softener
Bleach
Main 
Wa s h
Prewash
Start 
Delay
Pre-
wash
Stain
Tr e a t
Auto
Soak
2nd
Rinse
Extended
Spin
Sanitary
 
For heavily soiled colourfast cotton which needs sanitization.
This programme complies to the UK Care Standard Act 2000 
(CSA) Standard 26.
9.0
❉❉
Ye s
❉❉❉❉❉ ❉ ❉
1000 Max
White Cotton
 
 
For white cotton loads which you would like to bleach. An 
additional rinse provides optimal rinse performance to avoid 
chlorine residues on your laundry.
9.0
❉❉
Ye s
❉❉❉❉❉ ❉ ❉
1000 60
Heavy Duty
 
 
For normally soiled, sturdy and colourfast cotton. Use Stain 
Treat option for optimal removal of organic stains like blood, 
egg yolk etc.
9.0
❉❉
Ye s
❉❉❉❉❉ ❉ ❉
1000 60
Normal/Casual
 
 
For no-iron fabrics such as sport shirts, permanent press 
blends, cotton and linens.
3.5
❉❉
Ye s
❉❉❉❉❉ ❉ ❉
1000 60
Express Wash
 
 
For slightly soiled overalls and sports wear made of cotton, 
polyester, polyamide and blends with cotton.
2.0
❉❉
Ye s —
❉
——
❉❉ ❉
1000 60
Delicate
 
For curtains, delicate dresses, skirts, shirts and blouses.
2.5
❉❉
Ye s
❉❉❉
—
❉❉
— 800 50
Silk
For washable silk. Check care label instructions to make sure 
that garment is identified as machine washable.
2.0
❉
—Yes —
❉
—— —
❉
—0 50
Wo o l
For washable wool. Check care label instructions to make 
sure that garment is identified as machine washable.
2.0
❉
—Yes —
❉
—— —
❉
— 800 50
Ultra Handwash
For handwashable and special-care garments.
2.0
❉
—Yes —
❉
—— —
❉
— 600 50
Rinse / Spin
—
For a rinse and an extra high speed spin. If you wish you can 
reduce the speed.
9.0
❉
—— —
❉
—— —
❉❉
1000 50
Drain / Spin
—
For draining the washer with an additional extra high speed spin. 
If you wish you can reduce the speed.
9.0
————
❉
—— — —
❉
1000 —
A. Programme Sequence Indicator
B. Wash Cycles
C. “Start” Button
D. “Start Delay” button
E. Options
F. “Water Temperature” Modifier
G. “Spin Speed” Modifier
H. “End of Cycle” Signal Modifier
I. “Pause/Reset” Button
J. “Soil Level” Modifier
When you select an option an indicator lights
up.
If an option is not recommended for the
selected programme, the indicator light will
not light up and a warning sound advises that
this option is not possible.
If an option is selected after the programme
has started a sound will indicate that it is not
possible to select it at this stage.❉ : optional / yes: dosing required.
E
F
B
C
A
D
{
G
H
I
J
 
						

							5019 301 15169
Whirlpool is a registered trademark of Whirlpool USA
Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized 
conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect to the 
values in the table dependent on the water supply pressure and temperature, the load and the type of wash.
* The remaining time indicator can similarly deviate from the values in the table, because it takes into account the 
household conditions applicable at that time.Add the detergent as described in the programme table 
or in the chapter “Detergent and Additives” of the 
instructions for use.
1. Press the desired wash cycle.
2. The remaining time display shows the duration of 
the chosen programme (in hours and minutes) and 
the pilot lamp of the wash cycle button lights up.
3. The programme sequence, the predefined spin 
speed, water temperature, End of Cycle signal and 
options indicators corresponding to the selected 
programme light up. 
The recommendations can be altered by pressing the 
modifier and the option buttons.
Selecting any option the indication lights up.
When the combination of programme, additional 
options and modifiers is not possible, the indication 
lights switch off automatically and a signal sounds.
“Prewash” 
 For heavily soiled laundry.
 The cycle time increases approx. 15 minutes.
 Add detergent to the Prewash and Main Wash 
dispenser compartments.
 When using the Prewash compartment, do not use 
liquid detergent in the Main Wash compartment: 
use powder detergent for the main wash cycle. “Prewash” and “Auto Soak” options cannot be 
selected in the same cycle.
“Stain Treat”
 For heavily soiled laundry.
 Warm water fill for optimal organic soil removal and 
heat to high temperature.
“A u t o  S o a k ”
 For heavily soiled laundry with set-in stains. 
 The cycle time increases approx. 30 minutes.
 Use with a wash cycle:
Select the desired wash cycle and the “Auto Soak” 
option, add detergent to the Prewash and the Main 
Wash dispenser compartments; press the “Start” 
button. When using the Prewash compartment, do not 
use liquid detergent in the Main Wash compartment: 
use powder detergent for the main wash cycle.
 Use without a wash cycle:
Select first “Drain/Spin” or “Rinse/Spin” and then 
“Auto Soak” option; choose the desired soak 
temperature, add detergent to the Prewash 
compartment and press the “Start” button.
 “Prewash” and “Auto Soak” options cannot be 
selected in the same cycle.
“2nd Rinse”
 This option is recommended to ensure the removal 
of detergent or bleach residues from garments.
 It provides an additional rinse with the same water 
temperature as the first rinse.
 This option is particularly suitable for areas with 
very soft water, for baby clothes and to help people 
with allergies.CONSUMPTION DATA
Programme
Te m p e r a t u r e
°C
Load
(kg)
Wa t e r
(l)
Approximate programme 
duration*
(hours : minutes)
Sanitary Max 9.0 90 2:15
White Cotton 60 9.0 84 1:55
Heavy Duty 60 9.0 84 2:10
Normal/Casual 60 3.5 50 1:20
Express Wash 40 2.0 48 0:45
Delicate 40 2.5 65 0:55
Silk 30 2.0 60 0:35
Wool 30 2.0 60 0:40
Ultra Handwash 30 2.0 60 0:40
ADD DETERGENT, CLOSE THE DOOR AND 
SELECT THE PROGRAMMESELECT ANY DESIRED OPTION AND 
MODIFIER
“Extended Spin”
 This option is useful for adding an additional spin 
to any cycle to improve the “fluff ” of your 
laundry, to reduce drying time and to save energy
“Modifiers”
Preset cycle settings of water temperature (wash 
temperature/rinse temperature), spin speed (0 to 
1000), End of Cycle signal (off, low or high) and soil 
level (light, normal, heavy) can be changed. You can 
modify the settings by pressing the respective buttons. 
Changing the soil level leads to different programme 
durations.
The “Start Delay” allows to run the machine at the 
consumer’s convenience, for example at night when 
electricity may be cheaper.
 Select programme, modifier and options.
 Press the “Start Delay ” button to select the delay 
time by 1 to 10 hours;
 Press the “Start”
 button for at least 2 sec.
The time delay indication disappears when the 
programme starts and it is replaced by the 
remaining time.
 The number of hours preselected can later be 
reduced pressing again the “Start Delay ” button.
To cancel the “Start Delay”.
 Press the “Pause/Reset” button once.
 Press the “Start Delay ” button up to 00 h in the 
display.
Check the programme setting and press and hold 
the “Start”
 button.
Turn on the tap(s) and press the “Start”
 button for 
a few seconds.
The indicator lamps show the sequence reached in 
the programme. After starting the programme, the 
sequence indication runs from top to bottom through 
“Add a Garment” , “Soak/Prewash” , 
“Wash” , “Rinse” , “Spin”  and “End of 
Cycle” .
When a sequence of the programme is finished the 
corresponding lamp goes out.
After programme start and while the “Add a 
garment” lamp is on you can still add a garment. 
Press “Pause/Reset” button once. After few seconds 
the door will be unlocked and you can add the item. 
Close the door and press the “Start” button again. 
The programme will run again from the point where 
it was interrupted.After each programme start the door is locked and 
approx. 0.5 l of water is rinsed in. The door is 
unlocked for a few seconds. The door is then locked 
until the end of the programme. Detailed information 
can be found in the instructions for use.
 The time remaining is “0:00”, the “End of Cycle”-
light is on and a signal sounds, if selected.
1. Take out the load.
2.
Turn the tap off and leave the door ajar to allow 
the drum to dry out.
The control panel is switched off 5 minutes after  the 
end of the cycle, it is still possible to open the door.
1. Press the “Pause/Reset” button once to interrupt 
the programme. The light flashes.
2. Select the new programme with temperature, 
any options and modifier if you want.
3.
Press the “Start”
 button. The new programme 
continues at the same position where the 
previous programme was interrupted. Do not 
add detergent for this programme.
Press the “Pause/Reset” button twice. Any existing 
water is drained out before the door can be opened.
The “Controls Locked”  prevents unintended use 
of the washer. You can also use the “Controls 
Locked”  feature to prevent unintended cycle or 
option changes during a cycle. When “Controls 
Locked” is lit, all buttons are disabled. You can lock 
the washer while it is operating.
To lock the controls:
Select and hold “Drain/Spin”  button for 3 
seconds. The “Controls Locked” status indicator 
lights up.
To unlock the controls:
Select and hold “Drain/Spin”  button for 3 
seconds until the “Controls Locked”  status 
indicator is switched off.
START DELAYPROGRAMME STARTADD A GARMENT
DOOR LOCKPROGRAMME ENDCHANGE THE PROGRAMME, 
TEMPERATURE, OPTIONS AFTER 
PROGRAMME STARTCANCEL A PROGRAMME BEFORE THE ENDLOCKING CONTROLS
 
						

							5019 301 15169
Whirlpool is a registered trademark of Whirlpool USA
If you wish to connect only the cold 
fill follow the below 
instruction (Fig. 1):1. You need the enclosed Y-piece connector.
2. Fix the Y-piece connector to the cold fill 
tap.
3. Connect the two inlet valves present on 
the rear part of the machine to the Y-piece 
connector using the relative provider 
hoses.
Make sure: 
All connections are tightly fixed.
If you wish to connect 
hot and cold water supply 
(Fig. 2):1. Fix the red marked inlet hose at the hot 
water tap and at the inlet valve with the 
red filter on the rear side of machine.
2. Fix the other inlet hose at the cold water 
tap and at the inlet valve with the white 
filter on the rear side of the machine.
Make sure:
a) The connections are tightly fixed
b) Do not invert their position 
(for example: cold fill into hot inlet valve 
and viceversa). 
COLD / HOT FILL INSTRUCTIONFig. 1 Fig. 2
Do not allow children to operate, crawl on, near or inside your 
washer. 
Note that during wash cycles, the surface temperature of the 
porthole door may increase. 
Close supervision of children is necessary when the appliance is 
used near children. Please observe that both inlet valves (white and red) of the 
washing machine have to be connected to the water supply. 
There are two alternative ways of doing this:
Cold fill
Hot fill
Y- p i e c eCold fill
White inlet valve
Red inlet valveWhite inlet valve
Red inlet valve