Whirlpool Awe 8730 Programme Chart Manual

							
ProgrammeTempe-ratureCareLabels
Max.Load
kg Type of wash / Notes- Respect the manufacturer's recommendations on the care label
Detergents and additivesOptionsMaxspinspeedrpm
Pre- washMain 
WashSoftenerClean+EasyIronining Pre-washStartdelayIntensiverinseRinseHoldSpin
Mixed20 - 60°C3.0Slightly to normally soiled robust laundry made of cotton, linen, artificial fibres and their blends.Effective one-hour programme. Make sure to wash only similar colours together in one wash load. If soil level requires, add oxygen-based stain removers.–
Yes––max.
Fabrics
Cotton20 - 95°C5.5Normally to heavily soiled towels, underwear, table and bed linen etc. made of cotton and linen.
Yesmax.
Synthetics20 - 60°C3.0 Normally soiled blouses, shirts, overalls, etc. made of polyester (Diolen, T
revira), polyamide 
(Perlon, Nylon) or blends with cotton. Yesmax.
Delicates20 - 40°C1.5Curtains and delicate clothing, dresses, skirts, shirts and blouses.Yes–––1000 1)
Wool / Handwash20 - 40°C1.0 Woolens, labelled with the Woolmark and identified as machine washable, as well as textiles made of silk, linen, wool and viscose marked as handwashable.
This programme is tested and approved by The Woolmark Company for machine- and handwashable 
wool.Select spin speed according to the manufacturer‘s recommendation on the care label.–
Yes––––1000 1)
Jeans20 - 60°C5.5Normally soiled cotton jeanswear and garments made of jeanslike material such as trousers and jackets. Yes––max.
Colours
Whites20 - 60°C5.5Normally to heavily soiled and robust cotton laundry.Save energy by selecting a lower wash temperature and adding an oxygen-based bleach product, in addition to your detergent–
Yes–––max.
Light colours20 - 60°C4.0White and pastel shaded garments made of delicate fabrics.
Gentle wash programme to avoid graying or yellowing of your laundry . Use heavy duty detergent, if 
necessary also stain removers or bleaches on oxygen basis. Do not use liquid detergent.Yes–––1000 1)
Dark colours20 - 60°C4.0 Black and dark garments made of cotton, cotton blends and polyester
.
Special programme to reduce colour fading and local discolouration. P refer to use a liquid detergent for dark garments with this program.Yes––max.
Economy
AquaEco20 - 40°C2.5 Lightly soiled laundry made of synthetic fibres, or synthetics mix
ed with cotton garments. Saving programme with a very low water consumption. Use liquid detergent and the lowest 
recommended amount for 3kg laundry. Do not use softener.–Yes–––––max.
Speed1520 - 30°C3.0Briefly worn clothing made of cotton, artificial fibers and blends with cotton.
Refresh programme. Use lowest recommended detergent amount.–Yes––––max.
EcoCotton60°C5.5Heavily soiled and robust laundry washable at 60°C such as bed linen, table linen towels etc..The extended programme duration enables economic energy and water consumption while maintaining good washing results.–Yes–––max.
Rinse & Spin--5.5Rinse and intensive spin programme.
Same as the last rinse and the final spin in the “Cotton” programme.–––––max.
Drain---Drain only - no spinning. Alternative method of terminating programme after “Rinse Hold”.––––––––––
Whirlpool is a registered trademark of Whirlpool USA.:  optional / Yes : dosing required1)  For improved garment care, spin speed is restricted in these programmes.The wool and handwash cycles of this machine have been tested and approved by The Woolmark Company for the washing of Woolmark garments labelled as “machine wash” or “hand wash”provided that the garments are washed according to the instructions on the garment label and those issued in this programme chart.M0703
GB
5019 312 10782
PROGRAMME CHART
A.  Programme selector
B.  “Temperature” button
C.  Temperature display
D.  “Spin” button
E.  “Start delay ” button
F.  Time display
G.  “Start(Pause)” button H.  Programme sequence indicator
I.  “Door open” indication
J.  “Reset” button
This washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and react appropriately:
K.  “Service” indication
L.  “Water tap closed” indication
M.  “Clean filter ” indicationA
B
H
F
EG
C
D
J
I
K
L
M
 
						

							
5019 312 10782
ProgrammeTemperature(°C)Load(kg)Water(l)Energy(kWh)
ApproxProgrammeDuration*(hours : minutes)
Mixed403.0430.481:00Whites405.5530.652:15Light colours404.0700.551:20Dark colours404.0410.581:44 Cotton955.555**1.701:55Cotton605.5491.022:25Cotton405.5530.552:00Synthetics603.054**0.901:40Synthetics403.0480.551:25Delicates401.5510.500:45
Wool/Handwash401.0430.500:35Jeans405.5730.552:14AquaEco402.5190.451:00Speed 15303.0300.150:15EcoCotton  ***605.5490.833:20
CONSUMPTION DATA
Whirlpool is a registered trademark of Whirlpool USA.
Add detergent as indicated an the front page and as described in the chapter “Detergent and Additives” in your Instructions for Use.1.  Turn the programme selector to the desired
  programme. The display shows the programme
  duration in hours and minutes as well as the
  predefined temperature. The  “Start(Pause)”
 button
  flashes.
2.  The 
temperature can be altered by pressing the
  “Temperature” button.
3.  The indication lamp of the predefined 
spin speed
  lights up; in case you want to set another spin speed,
  press the “Variable spin” button.
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.*  The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions applicable 
  at that time.
**  To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***  Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE LID AND SELECT THE PROGRAMME
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to show the the lid can be opened. As long as a wash programme is running, the lid remains locked and must on no account be forced open. In case you have an urgent need to open it during a running programme, refer to “Cancel a running programme before the end”.
RED INDICATIONS
“Service”Lighting up of the “Service” indication can be caused 
by a fault in an electrical component. Refer to the 
“Troubleshooting Guide” in your “Instructions for Use”; 
if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open 
the water tap: if the indications still lights up, refer to the 
“Troubleshooting Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the 
drain hose is kinked or the filter must be cleaned: in the 
latter case refer to the Instructions for Use (“Removing 
the Filter”).
  together with your detergent (only use powder
  detergent with this option). Respect the
  manufacturer’s dosing instructions.
•  Prolongs the programme by approx. 10 to 15 minutes.
•  Appropriate for use of stain removers and bleaches
  on oxygen basis. 
Chlorine or perborate bleaches
  must not be used!
“Easy ironing” button•  Reduces creasing by an increased water quantity and
  a very gentle spin.
“Prewash” button
•  Only for heavily soiled loads (for example sand,
  granular dirt) sensible. Increases the cycle time by
  approximately 15 min.
•  Do not use liquid detergent for the main wash when
  activating the Prewash option.
“Intensive Rinse” button•  More water is added and rinse cycle is prolonged.•  This option is particularly suitable for areas with very
  soft water, washing baby linen and helping people
  with allergies.
“Rinse Hold” button
•  The laundry remains in the last rinse water without
  progressing to the final spin cycle to avoid creasing
  and prevent colours from changing.
• It is particularly useful if you want to postpone
  spinning to a later time, or if you want to drain only.• If you select “Rinse Hold”, do not leave items to
  soak for too long. Note: The programme stops to “Rinse hold” at the
  time the “Rinse hold” light in the programme
  sequence indicator is on. The indication lamp next to   the  “Start(Pause)”
 button flashes.
PROGRAMME START
Open the tap and press the  “Start(Pause)” button. The indication lamp next to the  “Start(Pause)” button lights up. The programme sequence indicator shows the current programme phase, running from left to right 
through Wash, Rinse, Spin/Drain. 
The display shows the remaining programme time. Due 
to variations in load and temperature of inlet water, the 
remaining time is newly calculated in certain programme phases. If this is the case, an animation appears on the time display.
PROGRAMME END
•  All the lights of the programme sequence indicator
  are off, and the “Door open” indication lights up.
1.  Turn the programme selector to the “Off/O”
  position.
2.  Close the water tap.
3.  Open lid and drum and unload the machine.
4.  Leave the lid open for some time to allow the
  interior of the machine to dry.
CHANGE PROGRAMME AND/OR OPTIONS 
AFTER PROGRAMME START
1.  Press the “Start(Pause)” button to pause the
  programme. The light flashes.
2.  Select the new programme, temperature, any
  options and another spin speed if you want.
3.  Press the  “Start(Pause)”
 button again. The new
  programme continues at the same position where
  the previous programme was interrupted. Do not
  add detergent for this programme.
CANCEL A RUNNING PROGRAMME BEFORE THE END
The  “Reset” button cancels a programme before the end.• Press the  “Reset” button for at least 3 seconds.  The   
  water is drained out; it may last a while until you can   
  open the lid.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the respective indication lights up.When the combination of programme and additional option(s) is not possible, the indication lights switch off 
automatically. Unsuitable combinations of options are 
deselected automatically.
“Clean+” button
•  Choose this option if you use an in-wash additive for
  stain removal ( powder, for example “Vanish”) - it
  will optimize the additive’s efficiency to get better
  wash performance and stain removal.
•  Choose temperature of 30 or 40°C and use with     
  maximum load.
•  Add an appropriate amount of in-wash additive for
  stain removal (powder) to the main wash chamber,
START DELAY
The “Start delay ” button allows to run the machine at the consumer's convenience, for example at night when 
electricity is cheaper. Do not use liquid detergent when 
activating the “Start delay ”.
•  Select programme, temperature and options.
•  Press the “Start Delay ” button to select the delay
  time up to 23 hours;
•  Press the  “Start(Pause)”
 button.
  The indication light over the “Start delay ” button
  flashes and the countdown of the delay time begins.
  The dot between hours and minutes of the delay
  time indicated flashes.
•  The time delay indication disappears when the
  programme starts and it is replaced by the remaining
  programme time.
•  Once having pressed the  “Start(Pause)”
 button,
  the number of hours preselected can be reduced by
  pressing and holding the “Start delay ” button. From
  1 hour on, the delay time can also be reduced in
  steps of 10 minutes
.
To cancel the “Start delay ”
..before you press the  “Start(Pause)” button:•  Turn the programme selector to another position
  or press the “Reset” button...after having pressed the  “Start(Pause)” button:• Press “Start (Pause)“ - the delay time disappears
  from the display; press  “Start (Pause)“ again to
  start the selected programme immediately. Terminate the “Rinse Hold” option:
•  Press the  “Start(Pause)” button; the programme
  will terminate automatically with the final spin cycle
  for the present wash programme.
•   If you do not wish to spin the clothes, turn the
  programme selector to “Drain” and press the
  “Start(Pause)”  button to start the Drain programme.
“Spin” button
•  Every programme has a predefined spin speed.
•  Press the button to set another spin speed.
•  If spin speed “0” is selected, the final spinning is
  cancelled but intermediate spin peaks remain during
  the rinse. The water is drained out only.