Whirlpool AWE 6519 User Manual

							CONTENTS
DEFINITION OF USE
BEFORE USING THE WASHING MACHINE
PRECAUTIONS AND GENERAL 
RECOMMENDATIONS
DESCRIPTION OF THE WASHING MACHINE
BEFORE THE FIRST WASH CYCLE
PREPARATION OF THE WASHING
DETERGENTS AND ADDITIVES
CLEANING THE FILTER/ 
DRAINING RESIDUAL WATER
CARE AND MAINTENANCE
TROUBLESHOOTING GUIDE
AFTER-SALES SERVICE
TRANSPORT AND HANDLING
INSTALLATION
ELECTRICAL CONNECTION
IFU-TL HR GB.fm  Page 1  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI 
 
						

							GB 2
DEFINITION OF USE
This washing machine is exclusively destined to wash 
machine washable laundry in quantities which are usual 
for private households.
•Observe the instructions given in these Instructions 
for Use and the Programme Chart when using the 
washing machine.Keep these Instructions for Use and the Programme 
Chart; if you pass on the washing machine to 
another person, also give him/her Instructions for 
Use and Programme Chart.
BEFORE USING THE WASHING MACHINE
1. Remove the packaging and check
a.Cut and remove the shrink-wrap.
b.Remove the top protection and the protective 
corners.
c. Remove the bottom protection by tilting and
 
turning the washing machine on one rear 
bottom corner. Make sure that the black 
plastic part of the bottom protection (if 
available on the model) remains in the packing 
and not in the machine bottom.
This is important, as otherwise the plastic part could 
damage the washing machine during operation.
d.Open the lid by pressing it slightly down while 
raising the handle. Remove the polystyrene cushion 
(depending on model).
e.Remove the blue protective film from the panel 
(depending on model).
After unpacking, make sure that the washing machine is 
undamaged. If in doubt, do not use the washing machine. 
Contact After-Sales Service or your local retailer.
Keep the packaging materials (plastic bags, 
polystyrene parts, etc.) out of reach of children; 
they are potentially dangerous.
If the appliance was exposed to the cold prior to 
delivery, keep it at room temperature for a few 
hours before operating.
2. Remove the transport bracket
The washing machine is fitted with transport screws 
and a transport bracket to prevent damage during 
transport. 
Before using the washing machine
 
you must remove the transport bracket (see 
“Installation”/“Removal of transport bracket”).
3. Install the washing machine
Place the washing machine on a flat and stable floor 
surface.
 Adjust the feet to ensure that the machine is stable
 
and level (see “Installation”/“Adjust the feet”).
In case of wooden or so-called “floating floors” (for 
instance certain parquet or laminate floors), place 
the appliance on a 40 x 60 cm sheet of plywood at 
least 3 cm in thickness which is secured to the floor.
Make sure that the ventilation openings in the base 
of your washing machine (if available on your model) 
are not obstructed by a carpet or other material.
4. Water supply
Connect the water supply inlet hose in accordance 
with the regulations of your local water company 
(see “Installation”/“Connect the water inlet hose”).
Water supply:  Cold water only 
Tap:  3/4” threaded hose connection
Pressure: 100-1000 kPa (1-10 bar).Only use new hoses for connecting the washing 
machine to the water supply. Used hoses must not 
be used anymore and should be discarded.
5. Drain hose
Connect the drain hose to the siphon or hook it 
over the edge of a sink with the “U” bend (see 
“Installation”/“Connect the water drain hose”).
If the washing machine is connected to a built-in 
drainage system, ensure the latter is equipped with 
a vent to avoid simultaneous loading and draining of 
water (siphoning effect).
6. Electrical connection
Electrical connections must be carried out by a 
qualified technician in compliance with the 
manufacturer’s instructions and the current 
standard safety regulations.
The technical data (voltage, power and fuses) are given 
on the rating plate on the rear of the washing machine.
The washing machine must be connected exclusively by 
means of a socket with an earth connection in 
accordance with current regulations. The washing 
machine must be earthed by law. The manufacturer 
declines all liability for injury to persons or animals or 
damage to property deriving directly or indirectly from 
failure to observe the directions.
Do not use extension leads or multi sockets.
Before any maintenance on the washing machine 
disconnect it from the mains supply.
Access to the mains plug or to disconnection from the 
mains supply via a double-pole switch must be ensured 
at all times following the installation.
Do not operate the washing machine if it has been 
damaged during transport. Inform the After-Sales Service.
Mains cable replacement is only to be carried out by 
After-Sales Service.
The washing machine must be connected to an effective 
earthing installation, in compliance with the regulations 
in force. In particular, washing machines installed in 
premises containing a shower or a bath must be 
protected by a differential residual current device of at 
least 30 mA. Earthing the washing machine is obligatory 
under the law. The manufacturer declines all liability for 
injury to persons or animals or damage to property 
deriving either directly or indirectly from failure to 
observe the directions in these Instructions for Use.
The washing machine may only be used in the 
household for the prescribed uses.
Dimensions:
Width: 400 mm
Height: 900 mm
Depth: 600 mm
IFU-TL HR GB.fm  Page 2  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI 
 
						

							GB 3
PRECAUTIONS AND GENERAL 
RECOMMENDATIONS
1.Safety instructions
The washing machine is appropriate for indoor 
use only.

Do not store flammable fluids near the appliance.

Do not place electrical appliances on the lid of 
your washing machine.

Children must be supervised to ensure that they 
do not play with the appliance.

This appliance is not intended for use by persons 
(including children) with reduced physical, sensory 
or mental capabilities, or lack of experience and 
knowledge, unless they have been given supervision 
or instruction concerning use of the appliance by a 
person responsible for their safety.

Do not attempt to force the lid open.

If necessary, the power cable may be replaced 
with an identical one obtained from our After-
Sales Service. The power cable must only be 
replaced by a qualified technician.
2.Packing

The packaging materials are 100% recyclable and 
bear the recycling symbol . Adhere to local 
regulations when disposing of packaging material.
3.Disposing of packaging and old washing 
machines

This appliance is marked according to the 
European directive 2002/96/EC on Waste 
Electrical and Electronic Equipment (WEEE).
By ensuring this product is disposed of correctly, 
you will help prevent potential negative 
consequences for the environment and human 
health, which could otherwise be caused by 
inappropriate waste handling of this product. 
The symbol   on the product, or on the 
documents accompanying the product, indicates 
that this appliance may not be treated as 
household waste. Instead it shall be handed over 
to the applicable collection point for the recycling 
of electrical and electronic equipment. 
Disposal must be carried out in accordance with 
local environmental regulations for waste disposal.
For more detailed information about treatment, 
recovery and recycling of this product, please 
contact your local city office, your household 
waste disposal service or the shop where you 
purchased the product.
The washing machine is built from reusable 
materials. It must be disposed of in compliance 
with current local waste disposal regulations. 

Before scrapping, cut off the power cable so that the 
washing machine cannot be connected to the mains.

Remove detergent from compartment if you 
intend scrapping your washing machine.
4.Energy saving tips

Achieve the best use of energy, water, detergent 
and time by using the recommended maximum 
load size.

Do not exceed the detergent dosages indicated 
in the manufacturer’s instructions.

The Eco Ball - a special system in the outlet - will 
prevent detergent loss from the drum to avoid 
detergent loss into the environment.

Use “Prewash” (if available on your model) for 
heavily soiled laundry only! Save detergent, time, 
water and energy consumption by not selecting 
“Prewash” for slightly to normally soiled laundry. 

Pretreat stains with stain remover or soak dried 
in stains in water before washing to reduce the 
necessity of a hot wash program.

Save energy by using a 60° C instead of a 95° C 
wash programme or a 40° C instead of a 60° C 
wash programme.

Save energy and time by selecting a high spin 
speed to reduce the water content in laundry 
before using a tumble dryer (for machines with 
adjustable spin speed).
5.General recommendations

Do not leave the washing machine connected 
when not in use. Turn off the tap.

Before cleaning or carrying out maintenance 
switch off the washing machine and disconnect it 
from the mains supply.
6.EC Declaration of Conformity

This washing machine has been designed, 
constructed and distributed in compliance with 
the safety requirements of EC Directives: 
2006/95/EC Low Voltage Directive
2004/108/EC Electromagnetic Compatibility 
Directive
IFU-TL HR GB.fm  Page 3  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI 
 
						

							GB 4
DESCRIPTION OF THE WASHING MACHINE
BEFORE THE FIRST WASH CYCLE
1.
Lid
2.
Detergent dispenser
3.
Drum
4.
Pump access behind filter
5.
After-Sales Service sticker (behind the 
filter cover)
6.
Mobility lever (depending on model)

To move the washing machine: pull 
the handle out a little bit by hand and 
pull it out to the stop with the foot.
7.
Adjustable feet
To remove any residual water used in testing by the manufacturer, we recommend that you carry out a 
short wash cycle without laundry.
1.
Open the tap.
2.
Close the drum flaps.
3.
Pour a small amount of detergent (about 30 ml) into the main wash chamber  of the detergent 
dispenser.
4.
Close the lid.
5.
Select and start a short programme (see separate programme chart).
1
2
3
4
57
6
IFU-TL HR GB.fm  Page 4  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI 
 
						

							GB 5
PREPARATION OF THE WASHING
Sort the laundry
1. Sort the laundry according to…
 Type of fabric / care label symbol
Cottons, mixed fibres, easy care/synthetics, 
wool, handwash items.
 Colour
Separate whites and coloureds. 
Wash new coloured items separately.
Size
Wash items of different sizes in the same load to 
improve washing efficiency and distribution in the 
drum.
 Fabric delicacy
Wash delicate articles separately: use a special 
programme for Pure New Wool , curtains 
and other delicates. Always remove curtain glides 
or wash curtains with the glides inside a cotton 
bag. Use the special programme for handwash 
fabrics. Wash stockings, belts and other small 
items or articles with hooks (e.g. bras) in special 
cotton bags for washing machines or in zipped 
pillow cases.2.Empty pockets
Coins, safety pins and similar items can damage 
your laundry as well as the washing machine’s 
drum and tub.
3. Fasteners
Close zips and fasten buttons or hooks; loose 
belts or ribbons should be tied together.
Stain removal

Blood, milk, egg and other organic substances are 
generally removed by the enzyme phase of the 
programme.

To remove red wine, coffee, tea, grass and fruit 
stains etc. add a stain remover to the main wash 
chamber   of the detergent dispenser.

Particularly stubborn stains should be treated 
before the wash.
Dyeing and bleaching

Only use dyes and bleaches that are suitable for 
washing machines.

Follow the manufacturer’s instructions.

Plastic and rubber parts of the machine may be 
stained by dyes or bleaches.
IFU-TL HR GB.fm  Page 5  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI 
 
						

							GB 6
Loading the laundry
1.
Open the machine lid by pulling it upwards.
2.
Open the drum by pushing the drum flap release 
(pictures “1a
” or “1b
” - depending on the model; 
models as shown on “1a
” have a fixed drum flap 
release which will not compress when pushed).
3.
Place the items of laundry into the drum one by one. 
Do not exceed the maximum load of the programmes 
indicated in the separate programme chart.
Notes:
- Overloading the machine will result in unsatisfactory 
washing results and creased laundry.
- Take care that the laundry does not overhang the 
drum; if this is the case, push the laundry down into 
the drum so that there is enough free space to close 
the drum flaps properly.
- Do not use the flaps to push the laundry into the 
drum.
4.
To close the drum, hold both doors in the middle again 
(picture “2
”).
ATTENTION: 
make sure that the drum flaps are 
properly locked - depending on the model:
- the metal hook must be completely hooked into the 
rear door flap - see picture “2a
”, or
- all metal hooks must be properly hooked inside the 
rear door flap, and the button must overlap the edge 
of the rear door flap - see picture “2b
”.
- check that no laundry gets stuck between the flaps, 
or between flaps and drum.
2
1b
1a
2a
IFU-TL HR GB.fm  Page 6  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI 
 
						

							GB 7
DETERGENTS AND ADDITIVES
Choice of the right detergents and 
additives
The type of detergent depends on:

type of fabric (cottons, easy care/synthetics, 
delicate items, wool).
Note: 
use only specific detergents for wool and 
garments made of microfibres (like sports or 
swimwear).

colour;

washing temperature;

degree and type of soiling.
Notes:

Do not use liquid detergents when activating the 
“Start Delay” function (if available on your 
machine).

Do not use liquid detergent for the main wash 
when activating the “Prewash” option or 
selecting a programme with “Prewash” (if 
available on your model).

Whitish residues on dark fabrics are caused by 
insoluble detergents components used in 
modern phosphate-free powder detergents. If 
you notice this problem, shake or brush the 
affected items or use liquid detergents.

Keep detergents and additives in a safe, dry place 
out of the reach of children.

Use only detergents and additives specifically 
produced for domestic washing machines.

If you use descaling agents, dyes or bleaches, 
make sure that they are suitable for washing 
machine use. 

Descaler could contain components that can 
damage parts of your washing machine.

Do not use solvents (turpentine, benzine, etc.).

Do not machine wash fabrics that have been 
treated with solvents or flammable liquids.
Dosage
Follow the instructions on the detergent pack in 
relation to:

the degree and type of soiling;

the size of the load;
-
full load: follow the detergent manufacturer’s 
instructions;
-
half load: 3/4 the amount used for a full load;
-
minimum load (about 1 kg): half the amount 
used for a full load;

water hardness in your area (ask for information 
from your water company): soft water requires 
less detergent than hard water.
Notes:

Too much detergent can result in excess foam 
formation, and the reduction of washing efficiency.If 
the washing machine detects excessive foam it 
may prevent spinning.

Insufficient detergent may result in:
grey laundry, deposits on the drum, tub and 
heater.

When using concentrated fabric softeners, add 
water in the detergents dispenser up to “MAX” 
level mark.

To prevent dispensing problems when using 
highly concentrated powder and liquid 
detergents, use the special detergent ball or bag 
supplied with the detergent and place it inside 
the drum.
IFU-TL HR GB.fm  Page 7  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI 
 
						

							GB 8
Using chlorine bleach

Wash your laundry in the desired programme 
(Cotton, Synthetics), adding an appropriate 
amount of chlorine bleach to the SOFTENER 
chamber (close the lid carefully).

Immediately after end of programme, start the 
“Rinse and Spin” programme to eliminate any 
residual bleach smell; if you want, you can add 
softener.

Never put both chlorine bleach and softener into 
the softener chamber at the same time.
Using starch powder
If you want to use starch powder, proceed as follows:

Wash your laundry in the desired wash programme.

Prepare the starch solution according to the 
starch manufacturer’s instructions.

Fill the prepared starch solution (maximum 
100 ml) into the softener chamber of the 
detergent dispenser.

Close the lid and start programme “Rinse and Spin”.
Where to put detergents and additives
Pour in the detergent:

Washing powder for prewash and main wash   

Washing powder for main wash without prewash 

Fabric softeners no more than to “MAX
” mark.

Stain removers

Water softeners (water hardness class 4)

Starch (dissolved in water; maximum 100 ml)
Be careful not to fill more than the “MAX
” level mark.
For programmes without prewash and temperatures from cold to 
40° C, it is recommended to use liquid detergents to avoid whitish 
residues on the laundry.()
IFU-TL HR GB.fm  Page 8  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI 
 
						

							GB 9
CLEANING THE FILTER/
DRAINING RESIDUAL WATER
The washing machine is provided with a self-cleaning 
pump. The filter keeps objects like buttons, coins, safety-
pins etc. which have been left in the laundry. 
We recommend to check and clean the filter regularly, at 
least two or three times a year.
Especially:

if the appliance is not draining properly or if it fails to 
perform spin cycles.

if the “Clean pump” indication lights up. 
IMPORTANT: 
make sure the water has cooled before 
draining the appliance. 
Residual water must be drained also before transporting 
the machine.
1.
Unplug the washing machine.
2.
Open the filter cover with a coin.
3.
Place a bowl beneath it.
4.
Turn the filter slowly anti-clockwise until the grip is 
vertical; do not remove it as yet.
5.
Wait until all the water has drained out.
6.
Now unscrew the filter completely and extract it.
7.
Clean the filter and the filter chamber.
8.
Make sure the pump impeller (in the housing behind 
the filter) is not obstructed.
9. Insert the filter again and screw it
 fully down in a 
clockwise direction to the stop (until the grip is 
horizontal).
10.
Pour approximately one litre of water into the washing 
machine via the drum and check that water does not 
leak from the filter.
11.
Close the filter cover.
12.
Reconnect the washing machine.
6
2
IFU-TL HR GB.fm  Page 9  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI 
 
						

							GB 10
CARE AND MAINTENANCE
Detergent dispenser
Clean the detergent dispenser regularly, at least three or 
four times a year, to prevent detergent build-up:
1.
Push in the buttons on each side of the dispenser.
2.
Pull the dispenser towards you and remove it.
A small quantity of water can remain in the dispenser. It is 
advisable to carry the dispenser in an upright position.
3.
Wash the dispenser using running water.
You can also remove the siphon caps in the dispenser for cleaning.
4.
Replace the siphon caps in the dispenser (if removed).
Make sure that they lock in place.
5.
Replace the dispenser by locating the bottom tabs in the lid 
holes and pivot until both of the upper buttons lock.
Note: ensure that the detergent dispenser is correctly
 
reinstalled.
Water inlet hose filter
Check and clean regularly (at least two or three times a year).
1.
Unplug the washing machine.
2.
Turn off the tap.
3.
Unscrew the hose from the tap.
4.
Carefully clean the filter located at the end of hose, without 
disassembling it, for example with a tooth-brush.
Note
: Do not submerge the hose in water.
5.
Screw the flexible hose back onto the tap by hand. Do not use 
pliers (risk of squashing the joint).
6. Turn on the tap and check that the connections are 
water-tight.
7.
Plug the washing machine back in.
Water inlet hose
Check the inlet hose regularly for brittleness and cracks and 
replace it if necessary using a new hose of the same type.
The inlet hose as shown on picture “A
” has a safety valve to 
prevent the appliance against uncontrolled water inlet; if the 
safety valve inspection window is red, the safety valve has been 
activated and the hose must be exchanged. Contact out After-
Sales Service or your specialist dealer to obtain a new inlet hose.
If your inlet hose has a transparent hose coating (fig. “B
”), 
periodically check the colour of the transparent coating. If the 
transparent hose coating turns into an intense red, this is an 
indication that the hose may have a leak and should be replaced. 
Contact our After-Sales Service team or specialist dealer to 
obtain a replacement hose.
B
A
Safety valve 
inspection 
window
C
IFU-TL HR GB.fm  Page 10  Friday, November 7, 2008  2:30 PM
Black process 45.0° 100.0 LPI