Whirlpool Aquasteam 9559 User Manual

							GB 11
Description of red indications
Red indication
lights up
Indication on big 
display
(if available on your 
model)Description
Causes
Solutions
“Water tap closed” ---Appliance has no or insufficient water supply. The 
“Start/Pause” light blinks.
Check whether:
Water tap is fully open and water supply pressure 
is sufficient.
Kinks are present in the water inlet hose.
Mesh filter of water supply hose is blocked (see 
“Care And Maintenance”.
The water hose is frozen up.
The safety valve inspection window of your water 
supply hose is red (provided your appliance has a 
water supply hose as shown on picture 
“B” - see 
previous chapter “Care And Maintenance”); 
replace the hose by a new one available through 
our After-Sales Service or your specialist dealer.
After problem has been removed, restart 
programme by pressing 
“Start/Pause”. If the fault 
occurs again, contact our After-Sales Service (see 
next chapter).
“Clean pump” ---Waste water is not pumped out. The appliance 
stops in the corresponding programme step; unplug 
it and check whether:
Kinks are present in the drain hose, or the hose is 
blocked for another reason.
Filter or pump is blocked (see chapter “Draining 
Residual Water/ Removing The Filter”; 
make sure 
the water has cooled before draining the 
appliance).
The drain hose is frozen up.
After problem has been removed, push the “Reset” 
button for at least 3 seconds; afterwards restart the 
desired programme. If the fault occurs again, 
contact our After-Sales-Service (see next chapter).
 
						

							GB 12
Red indication
lights upIndication on display
Description
Causes
Solutions
“Service”from “F02” to “F35”
(except “F24”)“Electrical module fault”
Push the “Reset” button for at least 3 seconds.
from “F40” to “F43” “Electrical module fault”
Make sure that the water tap is open. If yes:
Switch the washing machine off by turning the 
programme selector to the “Off/O” position; then 
turn the programme selector to a wash 
programme again. If there is still a failure:
Push the “Reset” button for at least 3 seconds.
“F24” “Water level too high” (after programme 
cancellation or false operating). Switch off the 
washing machine by turning the programme selector 
to the “Off/O” position. Turn the programme 
selector to a wash programme again, shortly press 
the “Reset/Drain” button and press 
“Start /Pause” 
within 15 seconds to start the Drain programme.
“F02” or “FA” “Waterstop fault”
Turn the programme selector to the “Off/O” 
position, pull out the mains plug and turn the water 
tap off. Tilt the appliance forward carefully to allow 
collected water to flow out from the bottom. Then:
Plug in the appliance again.
Turn the water tap on (if water immediately flows 
into the appliance without the appliance being 
started, there is a failure; turn off the tap and notify 
the After-Sales Service).
Select and start the desired programme again.
“Fod” “Overfoaming”
Too much foam interrupted the wash programme.
Select and start the “Rinse & Spin” programme.
Afterwards select and start the desired 
programme again, using less detergent.
If any of the faults described above persist, 
unplug the appliance, turn off the water tap 
and contact our After-Sales Service (see next 
chapter).
 
						

							GB 13
AFTER-SALES SERVICE
Before contacting After-Sales Service:
1.Try to remedy the problem yourself (see 
“Troubleshooting Guide”).
2.Restart the programme to check whether the 
problem has solved itself.
3.If the washing machine continues to function 
incorrectly, call our After-Sales Service.Specify:
The nature of the problem.
The washing machine model.
The service code (number after the word 
SERVICE).
The After-Sales Service sticker can be found 
inside the door.
Your full address.
Your telephone number and area code.
After-Sales Service phone numbers and 
addresses are given on the guarantee card. 
Alternatively, consult the dealer where you 
purchased the appliance.
ACCESSORIES
For some models, you can obtain via our After-
Sales Service or your specialist dealer:
a 
Pedestal Drawer which can be installed 
beneath your washing machine. It raises your 
machine to allow for more comfortable loading 
and unloading, as you now no longer need to 
bend as far to access the door. Furthermore, it 
offers a great space-management tool and 
storage solution.a 
Stacking Kit Shelf, by which your dryer can 
be fixed on top of your washing machine to save 
space and to facilitate loading and unloading your 
dryer in that high position.
TRANSPORT/HANDLING
Never lift the appliance by the worktop when transporting.
1.Pull out the mains plug.
2.Turn off the tap.
3.Check that machine door and detergent dispenser are properly closed.
4.Disconnect the inlet and drain hoses.
5.Eliminate all water from the hoses and from the appliance (see “Draining Residual Water/ Removing 
The Filter”).
6.Fit the transport bolts (obligatory).
 
						

							GB 14
ELECTRICAL CONNECTION
For Great Britain only
Warning - this appliance must be earthed
Fuse replacement
If the mains lead of this appliance is fitted with a 
BS 1363A 13amp fused plug, to change a fuse in this type 
of plug use an A.S.T.A. approved fuse to BS 1362 type and 
proceed as follows:
1.Remove the fuse cover (
A) and fuse (
B).
2.Fit replacement 13A fuse into fuse cover.
3.Refit both into plug.
Important:
The fuse cover must be refitted when changing a fuse and 
if the fuse cover is lost the plug must not be used until a 
correct replacement is fitted.
Correct replacement are identified by the colour insert or 
the colour embossed in words on the base of the plug.
Replacement fuse covers are available from your local 
electrical store.
For the Republic of Ireland only
The information given in respect of Great Britain will 
frequently apply, but a third type of plug and socket is also 
used, the 2-pin, side earth type.
Socket outlet / plug (valid for both countries)
If the fitted plug is not suitable for your socket outlet, 
Please contact After-Sales service for further instruction. 
Please do not attempt to change plug yourself. This 
procedure needs to be carried out by a qualified technician 
in compliance with the manufactures instructions and 
current standard safety regulations.