Whirlpool Adp 750 Ix Instruction Manual

							24
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
Ensure that the water inlet hose is not kinked or squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres; otherwise the cleaning effect of the dishwasher could be reduced.
Syphon Connection
The waste connection must be at a height of between 50 cm (minimum) and 100 cm (maximum) from the
bottom of the dish. The water drain hose should be fixed by a hose clip.
Start of DishwasherThe following things should be checked before starting the dishwasher.
1.The dishwasher is level and fixed properly
2.The inlet valve is open
3.There is a leakage at the connections of the conducts
4.The wires are tightly connected
5.The power is switched on
6.The inlet and drain hoses are knotted
7.All packing materials and printings should be taken out from the dishwasher
ATTENTION. After installation, please make sure to keep this manual.
The content of this manual is very helpful to the users.
 
						

							25
Before Calling for Service
Review the charts on the following pages may save you from calling for service.
Technical problems
TROUBLESHOOTING GUIDE
ProblemPossible causesWhat to do
Dishwasher
doesnt startFuse blown, or the circuit
breaker actedReplace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Power supply is not turned
onMake sure the dishwasher is turned on and the door is
closed securely. Make sure the power cord is properly
plugged into the wall socket.
Error code: E1;
Water pressure is lowCheck that the water supply is connected properly and
the water is turned on.
Door of dishwasher not
properly closed.Make sure to close the door properly and latch it.
Water not
pumped from
dishwasherKink in drain hose.Check drain hose.
Filter clogged.Check coarse the filter (see section titled  Cleaning
The Filter ).
Kitchen sink clogged.Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for
dishwashers.
General problems
ProblemPossible causesWhat to do
Suds in the tubeImproper detergent.Use only the special dishwasher detergent to avoid
suds. If this occurs, open the dishwasher and let suds
evaporate. Add 1 gallon of cold water to the tub. Close
and latch the dishwasher, then Start the soak wash
cycle to drain out the water. Repeat if necessary.
Spilled rinse-aid.Always wipe up rinse-aid spills immediately.
Stained tub
interiorDetergent with colourant
was used.Make sure that the detergent is the one without
colourant.
White film on
inside surfaceHard water minerals.To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Never use any other cleaner than dishwasher detergent
for the risk of foaming or suds.
There are rust
stains on cutleryThe affected items are not
corrosion resistant.–
A programme was not run
after dishwasher salt was
added. Traces of salt have
gotten into the wash cycle.Always run the quick wash programme.
without any crockery in the dishwasher and without
selecting the Turbo function (if present), after adding
dishwasher salt.
The lid of the softer is
looseCheck the lip .Ensure the fix is fine.
 
						

							26
Noise
ProblemPossible causesWhat to do
Knocking noise in
the washing
cabinetA spray armis knocking
against an item in a basketInterrupt the programme, and rearrange the items
which are obstructing the spray arm.
Rattling noise in
the washing
cabinetItems of crockery are
loose in the wash cabinetInterrupt the programme, and rearrange the items of
crockery.
Knocking noise in
the water pipesThis may be caused by on-
site installation or the
cross-section of the piping.This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
Unsatisfactory washing result
ProblemPossible causesWhat to do
The dishes are not
cleanThe dishes were not
loaded correctly.See notes in Loading the Dishwasher Baskets.
The programme was not
powerful enough.Select a more intensive programme.
See Wash Cycle Table .
Not enough detergent was
dispensed.Use more detergent, or change your detergent.
Items are blocking the
path of spray arms.Rearrange the items so that the spray can rotate freely.
The filter combination in
the base of wash cabinet is
not clean or is not
correctly fitted.
This may cause the sp ay
arm jets to get blocked.Clean and/or fit the filter combination correctly.
Clean the sp ay arm jets. See Cleaning the Spray
Arms.
Cloudiness on
glasswareCombination of soft water
and too much detergent.Use less detergent if you have soft water and select a
shortest cycle to wash the glassware and to get them
clean.
Black or grey
marks on dishesAluminum utensils have
rubbed against dishes.Use a mild abrasive cleaner to eliminate those marks.
Detergent left in
dispenser cupsDishes block detergent
cups.Re-loading the dishes properly.
 
						

							27
Unsatisfactory drying result
ProblemPossible causesWhat to do
The dishes are not
dryingImproper loadingLoad the dishwasher as suggested in the directions.
Too little rinse-aidIncrease the amount of rinse-aid/refill the rinse-aid
dispenser.
Dishes are removed too
soonDo not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once the
dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
Wrong program
has been selectedIn short program the washing temperature is lower.
This also lowers cleaning performance. Choose a
program with a long washing time.
Use of cutlery with
a low-quality coatingWater drainage is more difficult with these items.
Cutlery or dishes of this type are not suitable for
washing in the dishwasher.
Error codes
When some malfunctions come on, the appliance will display error codes to warn you:
CodesMeaningsPossible causes
E1Longer inlet time.Tap is not opened, or water intake is restricted,or
water pressure is too low.
E3Longer heating time,
but not reaching required
temperatureMalfunction of temperature sensor or of heating
element.
E4Overfilled.Too much inlet water.
E6Failure of temperature
sensorOpen circuit or break of temperature sensor
E7Failure of temperature
sensorShort circuit or break of temperature sensor
 If overflow occurs, turn off the main water supply before calling a service.
 If there is water in the base pan because of an overfill or small leak, the water should be
removed before restarting the dishwasher.
WARNING:
 
						

							28
TECHNICAL INFORMATION
Height850 mm
Width445 mm
Depth580 mm
Water pressure0.04-1.0 MPa
Hot water connectionMax 60°C
Power supplySee rating label
Capacity9 place settings