Whirlpool Adp 650 Wh Instruction Manual

							F use b lown, or the
circuit breaker actedReplace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Spilled rinse-aidAlways wipe up rinse-aid spills immediately.
Hard water minerals
The affected items are
not corrosion resistant.
The lid of the softer
is loose
Asp ayarmis
k nocking a gain st
an item in a basketr
Items of crockery
are loose in the
wash cabin et
This may be caused
b y on-site insta llatio n
or the cross-section of
the piping. A programme was not
ru n after dishwashe r
salt was added.
Traces of s alt h ave
gotten into the wash cycle.To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Ne ver u se any other clea ner than dishwashe r
detergent for the risk of foaming or suds.
Always run the quick wash programme .
without any crockery in the dishwasher and
without selecting the Turbo function (if present),
after adding dishwasher salt.
Check the lip .Ensure the fix is fine.
Interrupt the pro gram me, and rearr ange the item s
which are obstructing the sp ay arm.r
Interrupt the pro gram me,
an d rea rran ge th e items o f cro ckery.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
Detergent with
colourant was usedMake s ure that the deterg ent is the one with out
colourant.
Improper detergent
Make sure the dishwasher is turned on and the door is
closed securely.
Check that the water supply is connected properly and
the water is turned on.
Ma ke s ure to clo se the do or properly an d latch it.
Make sure the power cord is properly plugged into the
wall socket. Power supply is not
turned on
Error code:E1;
Water pressure is low
Door of dishwasher
n ot pr operly closed.
Kink in drain hose
Filter clogged
Kitchen sink cloggedCh eck drain hos e.
Check coarse the filter
(se e se ction titled ) Cleaning The Filter 
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Use only the special dishwasher detergent to avoid
suds. If this occurs, open the dishwasher and let suds
evaporate. Add 1 gallon of cold water to the tub. Close
and latch the dishwasher, then Start the soak wash
cycle to drain out the water . Repeat if necessary.
Before Calling for Service
19
Te c h n i c a l
problems
General
problems
Noise
 
						

							The dishes were not
lo aded cor rectly.See notes in  Loading the Dishwasher Baskets .
Select a more intensive programme.
See Wash Cycle Table .
Use more detergent, or change your detergent.
Rearrange the items so that the sp ay can rotate freely.r
Clean and/or fit the filter combination correctly.
Clean the sp ay arm jets. See Cleaning the Spray
Arms.r
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Use a mild abrasive cleaner to eliminate those marks.
Re-loading the dishes properly.
Load the dishwasher as suggested in the directions.
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Water drainage is more difficult with these items.
Cutlery or dishes of th is type are not suitable for
washing in the dishwasher.The programme was
not powerful enough.
Not enough detergent
was dispensed.
Items are block ing
the path of spray arms.
T he filter combinatio n
inthebaseofwash
c abine t is not c lean or
is not correctly fitted.
This may cause
the sp ay arm jets
to get blocked.r
Combination of soft
water and too much
detergent.
Aluminum utensils
have rubbed against
dishes.
Dishes block
detergent cups.
Improper loading
Too little rinse-aid
Dishes are removed
too soon
Wrong program
h as been s elec ted
Use of cutlery with
a low-quality co ating
Error Codes
Tap is not opened, or water intake is restricted,or water pressure
is too low.
Malfun ction of te mpe ratu re sensor or of hea ting elem ent.
To o m u c h i n l e t w a t e r .
Sh ort c ircuit or break of te mperature se nsor
Open circuit or break of temperature sensor
Longer inlet time.
Longer heating time,
but not reaching required temperature
Overfilled.
Failure of temperature sensor
Failure of temperature sensor
When some malfunctions come on, the appliance will display error codes to warn you:
WARNING!
If overflow occurs, turn off the main water supply before calling a service.
If there is water in the base pan because of an overfill or small leak,
the water should be removed before restarting the dishwasher.
20
Unsatis
-factory
washing
result
Unsatis
-factory
drying
result
 
						

							Height : 850mm
Width : 445mm
Depth : 580mm
Water pressure: 0.04-1.0MPa
Hot water connection : max 60℃
Power supply: see rating label
Capacity: 9 place settings
21
Technical Information