Whirlpool Adp 2300 Sl Quick Reference Guide

							GB 
-1-
Chart
PROGRAM SELECTION 
BUTTON
Push “Programs” button 
(repeatedly) until the indicator 
of the required program lights 
up (see “Table of programs” 
below).
START/RESUME BUTTON
Push this button to start the selected program: the 
indicator lights up and goes off at the end of the 
program. When the door is opened during a 
washing cycle, the cycle is temporarely paused: the 
Start indicator blinking. To restart the cycle close 
the door and push Start button again.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the program ongoing draining water for 1 minute.If pressed when the dishwasher is switched off it drains any possible liquids from dishwasher (1 minute process).If the indicator flashes repeatedly, see page 6 - 
chapter ”What to do if ...”.
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions 
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible 
with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for 
detailed information on the EN/Standard loading comparison test and other tests, contact the following address: 
“[email protected]”.
Table of programs
Deter-
gent
Consumption
P
Programs
Loading instructions
Litres
kWh
Minutes
1)
1
Pre-Wash
cold
Crockery to be washed later.
—
5.0
0.02
10
2
Quickwash
40°C
Lightly soiled crockery, with no dried-
on food.
X
13.0
0.70
30
3
Eco
2)
50°C
Normally soiled crockery.
X
15.0
1.05
150
4
Intensive
70°C
Recommended program for heavily 
soiled crockery, especially suitable for 
pans and saucepans.
X
15.0
1.50
140
5
Half Load
50°C
Ideal for washing a half load of lightly or 
normally soiled crockery.
X
13.0
1.00
130
5019 396 01823/B ADP 2300
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ 
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING 
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES 
AUTOMATICALLY AFTER 30 SECONDS IF ANY CYCLE IS STARTED.
Quick reference guide
 
						

							GB 
-2-
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
1.
Ask your water supply company what the water hardness
 is...
2.
...enter this value on 
your dishwasher
Suggestions for detergent use
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water hardness
level
3 first PROGRAM LEDs 
lit on the panel 
(see table of programs)
P1 P2 P3
Gel or Powder
(rinse aid and 
salt)
Ta b l e t s
0 - 5
0 - 9
0 - 6.3
Soft
1
go to step 1 
(see “Daily
check”)
6 - 10
10 - 18
7 - 12.6
Medium
2
11 - 15
19 - 27
13.3 - 18.9
Average
3
16 - 21
28 - 37
19.6 - 25.9
Medium-hard
4
if water is
HARD extra salt
needs to be
added
(go to step 1,
“Daily check”)
22 - 28
38 - 50
26.6 - 35
Hard
5
29 - 35
51 - 63
35.7 - 44.1
Very hard
6
36 - 60
64 - 107
44.8 - 74.9
Extremely hard
7
Water hardness should be set only 
before the first wash or if water 
hardness has been changed1
Visual indicator 
(depending 
on the model).
Unscrew cap.
Fill the salt reservoir with water 
before the first wash only.
(depending on the model)
The salt level indicator lamp may remain lit 
at the end of several wash cycles. If the 
water hardness level falls within category 
(soft), no salt is required.
Salt indicator on the control panel
Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT 
NEEDS TO BE ADDED.
orange: 
OK.
clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
- Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.
- Programs LEDs will indicate the water hardness setting.
-Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1.
- Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.
Add salt (never add detergent!)
min. 1.5 kg / max. 2 kg 
Water hardness level is 
factory set for medium-hard 
water (level 4).Even if you use tablets which 
include salt functionality, you 
must still add regeneration 
salt since such detergents are 
not effective enough at 
softening hard water.
Screw on the cap. 
Salt residual  
around the cap 
need to be 
removed. Some 
salt reservoir have 
a level indicator 
integrated in the 
cap (see below 
how to check).
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
How to set water hardness in order to always assure the best cleaning results
 
						

							GB 
-3-
Daily check
3
Check the rinse aid indicator to check the level 
into the dispenser.
(depending on the model)Rinse aid indicator on the control panel
Rinse aid indicator on the dispenser
The indicator lamp lights up when RINSE AID NEEDS 
TO BE ADDED.
dark: OK.
clear: NEEDS TO BE ADDED
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the 
appliance.If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty 
drying and a higher rinse aid setting will not improve the situation.Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with 
rinse aid incorporated tend to form excess suds.
Daily use
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A 
(press the dedicated button).
Only fill the 
detergent dispenser 
prior to starting a 
wash program.Shut the cover 
by pressing dedicated ribs. Insert detergent: Tablet / powder / liquid into the big chamber
Use only one tablet per one cycle, only 
placed in detergent dispenser.
All types of tablets can be used, but for 
2 in 1 type adding of salt is mandatory. If required, 
open the 
cover B 
(press the 
dedicated 
button).Add rinse aid 
to the max. 
line ~150 mlThe rinse aid dosage can be 
adjusted to the detergent used. 
The lower the setting, the less 
rinse aid is dispensed (factory 
setting: position 4).
Press the button to open the 
cover B. Using a coin or similar 
object, turn the arrow to the 
desired setting. After adjusting 
the rinse aid setting, shut the 
cover again. Visual 
indicator
2Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator
 
						

							GB 
-4-
How to load the racks
E - OPEN
(depending on the model)
F - Foldable plate holders: They can be folded down to load pots
or
G - Fixed plate holders
H - Cutlery basket (or I model)
J - Grid: Helps to keep the cutlery separate for better washing results.
H
How to load LOWER RACK4
A - Glass-holder for long stem glasses: it can be 
adjusted in 2 different positions according glasses shape.
B - Adjustable flaps: in horizontal position for cups/
long utensils, in raised position for plates.(in some models only)
C - Cutlery basket: it can be placed in the upper rack 
when the “Half load/Multizone” option is selected.How to adjust upper rack height 
(if available).
It could be useful to lift up the upper rack to have 
more space in lower rack or bring it down to load 
long stem glasses.
- Grasp and take out the two lateral handles (D)  
(they must be on the same level)
 a n d  l i f t  u p  o r  t a k e  
down the upper rack.
Arrange crockery so that water does not collect in cavities, ensuring that the spray arms turn freely. Only use dishwasher-proof crockery and dishes. Do not use the dishwasher for washing wooden 
items, aluminium, tin, silver cutlery or decorated crockery (unglazed). In the baskets, dishes (e.g. plates, bowls, pots) must be placed in a correct way to let water flow down!
E - CLOSED How to remove the upper rack (if available) 
It could be useful to remove the upper rack to load bulky items in the lower rack.
- Open the two retainers (E) to take off the upper rack (when the upper rack is in place 
the retainers must always be closed).
How to load UPPER RACK5
Switching on the appliance. Press any button except CANCEL/Off button to exit Standby and enter program selection mode.
 
						

							GB 
-5-
Switch off the appliance Everything o.k. ...Wash cycleSelect program6
7
8
Exercise caution when opening the door: beware of hot steam.
Press the CANCEL/Off button once to turn the appliance into Standby mode.
All the indicator lamps switch off. Unload the appliance, starting from the lower rack in order to avoid any residual drips of water falling onto crockery below.
Maintenance and care
Maintenance and care
Overview of programs
The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1).
Choose program according to the attached table of programs (page 1).
Duration of the program depends on the external conditions in the apartment, temperature and pressure etc.
The dishwasher door must be closed and the water tap open.To pause the program (e.g. if you want to insert an item):- Open the door with caution (the program pauses) and insert the 
item/s,
(beware of HOT steam!).
- Close the door and press the 
START button again to restart the 
cycle (the program resumes the cycle from where it was 
interrupted).
To Cancel the program on running:-Press the 
CANCEL/Off button.
- (Water drains for up to 1 minute then 
the appliance switches off).
To change the program in progress:- Press the 
CANCEL/Off button to cancel the program on running.
- (Water drains for up to 1 minute then the appliance switches off).
- Press any button except 
CANCEL/Off button to switch on the 
appliance.
- Select a new program.
- Press the 
START button.
Rectifying minor faults yourself ...109Filters
Check and 
clean if 
necessaryUnscrew filter 
cylinder, remove it 
and fine sieve...Rinse under running 
water ...Screw on filter cylinder NOTE MARK!
Unscrew 
and remove 
upper arm ... Spray arms 
Remove
blockages/
deposits.Insert
Clean spray 
nozzles under 
running water
(use toothpicks 
if necessary) ...Insert and screw on lower and upper arms tightly.
Unscrew 
and remove 
lower arm ...
 
						

							GB 
-6-
What to do if...
If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem.
Most faults can be remedied by taking the courses of action, quickly restoring normal appliance operation.
The appliance... Possible causes... Solutions...
...is not working/will not start
- The appliance must be switched on.
- Check the household circuit fuse if there is no power supply.
- The dishwasher door doesn’t close.
- Check if the dishwasher’s door is closed.
- “Delayed start” option is ON.
- Check whether the “Delayed start” option (if available) has been selected. If it has, the appliance will only 
start once the set time has elapsed. If necessary, set the delayed start to “0” (RESET the appliance).
...the CANCEL/Off indicator lamp blinks 6 
times- Water tap closed. - The water tap must be open.
- Kinked water inlet hose or clogged inlet filters.- The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be 
dirty or clogged.
- Water pressure too low. - The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).
...the CANCEL/Off indicator lamp blinks 6 
times/wash program ended too early 
(dishes are dirty and wet)
- Dirty or clogged filters.
- The filters must not be dirty or clogged.
- Too little water in the dishwasher’s water system.
- Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack.
- Drain hose incorrectly fitted.
- The drain hose must be fitted correctly (for high mounted appliances, leave min. 200-400 mm from the 
lower edge of the appliance) - see Assembly instructions.
- High level of foam inside.
- Repeat without detergent or wait until foam disappears.
...the CANCEL/Off indicator lamp blinks 8 
times- Dirty filters. - Clean the filters.
- Kinked drain hose. - The drain hose must not be kinked.
- Syphon hose connection closed. - The closure disk of the syphon hose connection must be removed.
After taking the above course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated.
RESET:Press the CANCEL/Off button.
Close the door.
Water drains automatically for up to 1 minute.
The appliance is now ready to be restarted.
Crockery and cutlery... Possible causes... Solutions...
...are not perfectly clean/have food residues
- Too little space between dishes (incorrect arrangement 
of the concave items in the rack).
- Arrange crockery so that items do not touch each other. Concave items (e.g. bowls, cups) must be 
arranged facing downwards in the rack.
- Too little detergent; detergent too old or incorrectly stored.
- If necessary, use more detergent, observing the manufacturer’s indications as regards dosage. Always store 
detergent in a dry place and do not store it for excessively long periods of time.
- Temperature not high enough for heavily soiled crockery.
- For heavily soiled crockery, select a wash program with a higher temperature (see table of programs - 
page 1).
- Loading of the dishwasher using lower and upper rack 
at the same time with “Half load/Multizone” option.
- If you select the “Half load/Multizone” option (if available), remember to load only the upper rack or only 
the lower rack to increase washing power and thus obtain optimum wash results.
- Frequent use of Eco 50°C.
- In the event of frequent use of the Eco 50°C program (if available), from time to time select the Intensive 
70°C program (if available).
- Clogged spray arms, dirty filters or not fitted correctly.
- The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see page 5, 
“Maintenance and care“).
- Spray arms stuck impeded by crockery or cutlery.
- The spray arms must be able to turn freely and must not be impeded by crockery or cutlery.
 
						

							GB 
-7-
What to do if...
Crockery and cutlery... Possible causes... Solutions...
...salt indicator lit
- Use tablets for soft water.
- Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up.
...have deposits: regeneration salt residue- Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water 
hardness”).
- Salt reservoir cap open. - Close the salt reservoir cap properly.
- Not enough rinse aid. - If you use a combined action detergent, try adding more rinse aid.
...are not dry
- Plastic containers dry badly.
- Synthetic materials do not dry well; if wet at end of cycle, wipe dry.
- Clean dishes left in dishwasher for a long time after end 
of cycle (e.g. when using “Delayed start” option).
- In this situation, the presence of drops of water on dishes and on the sides of the dishwasher is normal. 
Try releasing the door 5 minutes before removing the dishes.
- Incorrect arrangement of the concave items in the rack.
- Arrange crockery so that water does not collect in cavities.
- Incorrect dosage the rinse aid.
- Increase the dosage of rinse aid (see page 3, “Adding rinse aid”).
-Rapid program selected.
- The rapid program is intended for quickly washing lightly soiled dishes. If used for a full load of medium/heavy 
soiled dishes, the dishes may not dry completely. If so, select a standard-length program. For best results, 
open the door after the end of the program and wait 15 minutes before unloading the dishwasher.
...have discoloured plastic parts- Tomato/Carrot juice. - Tomato sauce, for example, can lead to discolouring of plastic parts. Powder detergent is recommended as 
it allows slightly higher doses to be used for improved whitening. Programs with higher wash temperatures 
should be used.
...opaque glasses, etc.
- Dishes unsuitable for washing in dishwashers (porcelain),
- Only use dishwasher-proof crockery and dishes.
...removable deposits on glasses- Usage of incorrect programs for glasses. - Dishes should be put together, to avoid touching each other. Do not put glassware together in baskets. 
Use suitable program for glass.
...glasses not sparkling- Not conform of glasses to washing in dishwashers 
(porcelain).- Some kinds of glass cannot be washed in the dishwasher.
...permanent deposits on glasses
-Rainbow effect.
- This phenomenon is irreversible. We recommend in future:
- Change the control of system of dosage of softener.
- Be careful – follow recommended detergent dosage.
- For combined action tablets see detergent producer’s recommendations.
...tea cups darken and dirt does not 
disappear after washing in dishwasher- Not known.
- This phenomenon is inevitable. Theine alters colours permanently.
...rust marks
- Pre-wash program not used.
- Salty or acidic food residues can cause rust marks even on stainless steel cutlery. To avoid this, always use 
the pre-wash program if the dishes are to be washed later.
...other marks- Rinse aid dosage too low. - In the presence of marks, increase the rinse aid dosage (see page 3, “Adding rinse aid”).
- If you use a combined action detergent, possibly add more rinse aid.
...streaks
- Rinse aid dosage too high.
- In the presence of streaks, reduce the rinse aid dosage (see page 3, “Adding rinse aid”).
- If you use a combined action detergent which includes rinse aid, do not add any additional rinse aid.
...suds- Unsuitable dosage of detergent/rinse aid.- Only use the amount of detergent/rinse aid required, since excessive amounts can lead to excess suds.
 
						

							GB 
-8-
What to do if...
If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).
Before contacting our After-Sales Service, take note of the following:
- the description of the fault,
- the appliance type and model,
- the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:
Precautions and general recommendations
1. Packing
The packaging materials are 100% recyclable and marked with the recycling symbol  .
2. Removing the packaging and inspecting the contents
After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, 
contact a qualified technician or your local retailer. 
3. Before using the dishwasher for the first time
- The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
- This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may 
leave slight drips/water marks which will disappear with the first wash.
4. Energy and water savings
- Do not rinse crockery under running water.
- Always fully load the dishwasher before running it or select the “Half load/Multizone” option (if available).
- If ecological energy sources are available such as solar panel heating, heat pumps or centralised heating 
systems, the appliance may be connected to the hot water mains up to a maximum temperature of 60°C. 
Make sure the water inlet hose is of the correct type (“70°C Max” or “90°C Max”).
5. Child safety
- Keep the packaging materials out of the reach of children. 
- Children must not be allowed to play with the dishwasher. 
- Store the detergent, rinse aid and salt out of the reach of children.
6. Safety warnings
- The appliance is not intended for use by children or physically or mentally impaired persons, unless 
adequately supervised by a responsible adult capable of guaranteeing safe use of the appliance. 
- Do not operate the appliance in the open air. 
- Do not store flammable materials in close proximity to the dishwasher. 
- The water in the dishwasher is not potable. 
- Do not use solvents inside the dishwasher: risk of explosion! 
- Be careful when the door is open: risk of tripping! 
- The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest 
objects on the open door or sit or stand on it.
- Sharp items that might cause injury (e.g. knives), must be placed in the cutlery basket with the sharp end 
facing downwards. Long-handled utensils must be arranged horizontally in the upper rack, with the sharp 
end facing away from the front of the appliance.
- Before cleaning or carrying out maintenance, disconnect the mains plug and turn off the water tap; also in 
the event of any malfunction.
- Repairs and technical modifications must be carried out exclusively by a qualified technician.
7. Resistance to frost
If the appliance is placed in surroundings exposed to the risk of frost, it must be drained completely. Turn off 
the water tap, remove the inlet and outlet hoses, and let all the water drain away. Make sure there is at least 
1 kg of dissolved regeneration salt in the salt reservoir, to protect the appliance from temperatures of up to 
-20°C. When the program resumes, an error message may be indicated (see page 6).
CANCEL/Off indicator blinks 6 times - the appliance must remain at an ambient temperature of min. 5°C for 
at least 24 hours. 
After eliminating these faults, RESET the appliance (see chapter “What to do if...”).
8. Disposal
- The appliance is manufactured using recyclable materials. If you decide to scrap the dishwasher, it must be 
disposed of in compliance with local waste disposal regulations. Make it unusable by cutting off the power 
cord. To prevent situations of potential danger to children (e.g. danger of suffocation), break the lock of the 
door so that it can no longer be closed.
- This appliance is marked according to the European directive 2002/96/CE on Waste Electrical and 
Electronic Equipment (WEEE). By ensuring that this appliance is scrapped suitably, you can help prevent 
potentially damaging consequences for the environment and health. Unsuitable disposal of an appliance of 
this type as household waste could have detrimental effects on the environment. The symbol   on the 
appliance, or on documentation enclosed with the appliance, indicates that this product must not be 
treated as household waste, but must be delivered to the nearest collection centre for the recycling of 
electrical and electronic appliances. Disposal must be carried out in accordance with local environmental 
regulations for waste disposal. For further information on the treatment, recovery and recycling of this 
appliance, contact your competent local authority, the collection service for household waste or the shop 
where you purchased the appliance.
EC Declaration of conformity
This appliance has been designed, constructed and distributed in compliance with the safety requirements of 
EC Directives:   2006/95/CE, 89/336/CE, 93/68/CE and 2002/95/CE (RoHS Directive). 
Loading Capacity: 12 place settings.
The guarantee is not applicable if faults are caused by incorrect use of the appliance.Disconnect the mains plug
We reserve the right to make technical modifications.