Whirlpool Adg 9590 Quick Reference Guide

							GB 
-1-
Chart
PROGRAM SELECTION 
BUTTON
Push “Programs” button 
(repeatedly) until the indicator 
of the required program lights 
up (see “Table of programs” 
below).
(see at right for options description)
START/RESUME BUTTON
Push this button to start the selected program: the 
indicator lights up and goes off at the end of the program. 
When the door is opened during a washing cycle, the 
cycle is temporarily paused: the Start indicator blinks. 
To resume the cycle push Start button and close 
the door within 3 seconds.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the program ongoing draining water for 1 minute (0:01 is shown into the display).If pressed when the dishwasher is switched off, it drains any possible liquids from dishwasher (1 minute process). 
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions (without 
additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible with sensor 
programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for detailed information 
on the EN/Standard loading comparison test and other tests, contact the following address: “[email protected]”.
Table of programs
Deter-
gent
Consumption
Drying
Phase
P
Programs
Available
options
Loading instructions
Litres
kWh
Minutes
1)
1
Aqua Steam
40-70°C
Delay
Multizone
Power
Clean
Normally or heavily soiled crockery, 
including pots and pans. Thanks to 
steam action, soaking or hand 
pretreatment is no longer needed. 
In addition hygiene is ensured due 
to the high temperature steam.
X
7-14
0.99-1.80
70-160
Full
2
Pre-Wash
cold
Delay
Multizone
Crockery to be washed later.
—
4.0
0.03
14
NO
3
Glasses
40°C
Delay
Multizone
Light soiling, for example glasses 
and cups.
X
10.0
0.85
100
Light
4
Quickwash
45°C
Delay
Multizone
Lightly soiled crockery, with no 
dried-on food.
X
11.0
0.80
30
NO
5
Eco
2)
50°C
Delay
Multizone
Power
Clean
Normally soiled crockery. 
Energy-saving program.
X
11.0
0.98
185
Full
6
Overnight
55°C
Delay
Multizone
Normally soiled crockery, gentle 
and quiet thanks to the lower spray 
pressure (39 dbA).
X
13.0
1.20
290
Light
5019 396 03521
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ 
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!Options and display descriptionSALT INDICATOR
When lit (at the end of 
the cycle), the salt 
reservoir needs to be 
refilled.
RINSE AID 
INDICATOR
When lit (at the end of 
the cycle), the rinse aid 
dispenser needs to be 
refilled.
WASH TIME DISPLAY
Indicated the cycle duration and the remaining time (h:min). With “Delayed start” selected it indicates 
the time remaining until program start (h.00) - below 1h (0:min).
If “Fx Ey” messages appears on the display, see page 6 - chapter “What to do if...”.THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING 
ANY BUTTON EXCEPT CANCEL/OFF BUTTON. FOR ENERGY SAVING 
THE CONTROL PANEL DEACTIVATES AUTOMATICALLY AFTER 30 
SECONDS IF NO CYCLE HAS STARTED.MULTIZONE
Allows you to choose the washing 
zones. Press this button (repeatedly) 
to select the wash zones:
both racksonly lower rackonly upper rack
 - indicator lits
TABLET SETTING
This setting allows to 
optimize the cycle 
performances according 
the type of detergent 
used. Push the Tablet 
button for 3 seconds (until 
the indicator lights up) if 
you are using the 
combined detergents in 
tablet (rinse aid, salt and 
detergent in 1 dose). If you 
are using powder 
detergent or liquid 
detergent, the Tablet 
indicator on the control 
panel has to be off.
DELAYED START 
BUTTON
Push the button 
(repeatedly) to delay the 
start of the  program. 
Adjustable from 1 to 24 
hours. With each press of 
the button, the delayed 
start indicator increases 
by one hour and after 24 
restarts from 0. Then 
press the START button. 
The dishwasher will start 
after the set time.
POWER CLEAN
Thanks to the additional power jets 
this option provides a more intensive 
and powerful wash in the lower rack, 
in the specific area. This option is 
recommended for washing pots and 
casseroles (see page 4). Press this 
button to activate Power Clean (the 
indicator lights up).
OPERATION 
INDICATOR
A LED light projected 
on the floor indicates 
that the dishwasher is 
working.
Quick reference guide
 
						

							GB 
-2-
First time use
1- salt reservoir
2- rinse aid dispenser
3- detergent dispenser
4- racks system
5,6,7,8- available functions on the panel
9- filters
10- spray arms
Water hardness should be set only 
before the first wash or if water 
hardness has been changed1
Visual indicator 
(depending 
on the model).
Unscrew cap.
Fill the salt reservoir with water 
before the first wash only.
(depending on the model)
The salt level indicator lamp may remain lit 
at the end of several wash cycles. If the 
water hardness level falls within category 
(soft), no salt is required.
Salt indicator on the control panel
Salt indicator on the salt reservoir cap
The indicator lamp lights up when SALT 
NEEDS TO BE ADDED.
green: OK.
clear: NEEDS TO
BE ADDED
Daily check
Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)
-Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.
- The current water hardness setting will be visible on the display.
-Press the Programs
 button to increase setting. Value range goes from 1 to 7 (when the level reaches 7, the next press of 
the start button will set the level back to 1).
- Wait 30 seconds (control panel switches off) or press Start/Resume button to save setting.
Add salt (never add detergent!)
min. 0.8 kg / max. 1 kg Screw on the cap. 
Salt residual  
around the cap 
need to be 
removed. Some 
salt reservoir have 
a level indicator 
integrated in the 
cap (see below 
how to check).
At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).
1.
Ask your water supply company what the water hardness
 is...
2.
...enter this value on 
your dishwasher
Suggestions for detergent use
German
degrees °dH
French
degrees °fH
English
degrees °eH
Water hardness
level
Insert value is shown 
in the display
Gel or Powder
(rinse aid and salt)
Ta b l e t s
0 - 5
0 - 9
0 - 6.3
Soft
1
go to step 1 
(see “Daily
check”)
6 - 10
10 - 18
7 - 12.6
Medium
2
11 - 15
19 - 27
13.3 - 18.9
Average
3
16 - 21
28 - 37
19.6 - 25.9
Medium-hard
4
if water is
HARD extra salt 
needs to be added
(go to step 1,
“Daily check”)
22 - 28
38 - 50
26.6 - 35
Hard
5
29 - 35
51 - 63
35.7 - 44.1
Very hard
6
36 - 50
64 - 90
44.8 - 62.4
Extremely hard
7
Water hardness level is factory 
set for medium-hard water 
(level 4).Even if you use tablets which 
include salt functionality, you 
must still add regeneration salt 
since such detergents are not 
effective enough at softening 
hard water.
How to set water hardness in order to always assure the best cleaning results
 
						

							GB 
-3-
Daily check
3
Check the rinse aid indicator to check the level 
into the dispenser.
(depending on the model)Rinse aid indicator on the control panel
Rinse aid indicator on the dispenser
The indicator lamp lights up when RINSE AID NEEDS 
TO BE ADDED.
dark: OK.
clear: NEEDS TO BE ADDED
Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the 
appliance.If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty 
drying and a higher rinse aid setting will not improve the situation.Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with 
rinse aid incorporated tend to form excess suds.
Daily use
Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
Open the cover A 
(press the dedicated button).
Only fill the 
detergent dispenser 
prior to starting a 
wash program.Shut the cover 
by pressing dedicated ribs. Insert detergent: Tablet / powder / liquid into the big chamber
Use only one tablet per one cycle, only 
placed in detergent dispenser.
All types of tablets can be used, but for 
2 in 1 type adding of salt is mandatory. If required, 
open the 
cover B 
(press the 
dedicated 
button).Add rinse aid 
to the max. 
line ~150 mlThe rinse aid dosage can be 
adjusted to the detergent used. 
The lower the setting, the less 
rinse aid is dispensed (factory 
setting: position 4).
Press the button to open the 
cover B. Using a coin or similar 
object, turn the arrow to the 
desired setting. After adjusting 
the rinse aid setting, shut the 
cover again. Visual 
indicator
2Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator
 
						

							GB 
-4-
How to load the racks
D - OPEN
How to load LOWER RACK4
(depending on the model)
A - Adjustable flaps: in horizontal position for 
cups/long utensils.B - Cutlery basket - half: can be placed in the upper rack 
when the “Half load/Multizone” option is selected.
The Grid (G) should be removed.How to adjust upper rack height (if available).
It could be useful to lift up the upper rack to have 
more space in lower rack or bring it down to load 
long stem glasses.
- Grasp and take out the two lateral handles (C
)  
(they must be on the same level)
 a n d  l i f t  u p  o r  t a k e  
down the upper rack.
Arrange crockery so that water does not collect in cavities, ensuring that the spray arms turn freely. Only use dishwasher-proof crockery and dishes. Do not use the dishwasher for washing wooden 
items, aluminium, tin, silver cutlery or decorated crockery (unglazed). In the baskets, dishes (e.g. plates, bowls, pots) must be placed in a correct way to let water flow down!
D - CLOSED How to remove the upper rack (if available) 
It could be useful to remove the upper rack to load bulky items in the lower rack.
- Open the two retainers (D) to take off the upper rack (when the upper rack is in 
place the retainers must always be closed).
Power Clean uses the special 
water jets in the rear of cavity 
to wash more intensively the 
high dirty items.How to use Power Clean
1. Adjust the Power Clean area (H
) folding down 
the rear plate holders to load pots.2. Load pots and casseroles inclined vertically in 
Power Clean area. Pots have to be inclined 
towards the power water jets.
E - Vertical plate holders: they can be folded down to load pots.
F - Cutlery basket:
 slide halves apart to split the basket.
G - Grid: helps to keep the cutlery separate for better washing results.
Switching on the appliance. Press any button (except CANCEL/Off button) to switch on the control panel and start programming. How to load UPPER RACK
5
 
						

							GB 
-5-
Switching off the appliance. Everything OK...Wash cycleSelect program6
7
8
Maintenance and care
Maintenance and care
Overview of programs
The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1).
Choose program according to the attached table of programs (page 1).
Duration of the program depends on the external conditions in the apartment, temperature and pressure etc.
Rectifying minor faults yourself...109Filters
Check and 
clean if 
necessaryUnscrew 
microfilter (1), 
remove it (2) 
and remove 
fine sieve (3)...Rinse under 
running water...Screw on microfilter NOTE MARK!
Unscrew 
and remove 
lower arm... Spray arms 
Remove
blockages/
deposits.Insert
Clean spray 
nozzles under 
running water
(use toothpicks 
if necessary)...Insert and screw on upper and lower arms tightly.
Unscrew 
and remove 
upper arm...
The dishwasher door must be closed and the water tap open.To pause the program (e.g. if you want to insert an item):- Open the door with caution (the program pauses) and insert 
the item/s,
(beware of HOT steam!).
-Press the 
START button and close the door within 3 seconds 
(the program resumes the cycle from where it was 
interrupted).
To Cancel the program on running:- Open the door, press the 
CANCEL/
Off button and close the door.
- (Water drains for up to 1 minute then 
the appliance switches off).
To change the program in progress:- Open the door, press the 
CANCEL/Off button to cancel the 
running program and close the door.
- (Water drains for up to 1 minute then the appliance switches off).
- Open the door and press any button except 
CANCEL/Off button to 
switch on the appliance.
- Select a new program.
- Press the 
START button and close the door within 3 seconds
After the program is completed appliance turns into 
Standby mode automatically. All indicator lamps switch off. 
Exercise caution when opening the door: beware of hot steam. 
Unload the appliance starting from the lower rack in order to avoid any residual drips of water falling onto crockery 
below.
For even better drying results, leave the dishwasher door open a little 
before unloading in order to allow the steam to dissipate, helping the 
dishes to dry. The underside of the kitchen worktop must be protected 
(see instructions in ‘Assembly instructions’).
 
						

							GB 
-6-
What to do if...
If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem.
Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation.
How the faults are shown on the display: Function number “F”x - blinkingError number “E”y - blinking 0.5 sec. pause
The appliance... Possible causes... Solutions......is not working/will not start
- The appliance must be switched on.
- Check the household circuit fuse if there is no power supply.
- The dishwasher door doesn’t close.
- Check if the dishwasher’s door is closed.
- “Delayed start” option is ON.
- Check whether the “Delayed start” option (if available) has been selected. If it has, the appliance will only start once the set 
time has elapsed. If necessary, set the delayed start to “0” (RESET the appliance).
...shows “F6 E2”
- Water tap closed. - The water tap must be open.
- Kinked water inlet hose or clogged inlet filters. - The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be clogged.
...shows “F6E7” or “F6E1”
- Water pressure too low.
- The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).
- Kinked water inlet hose or clogged inlet filters.
- The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be dirty.
...shows “F6 E3”/wash program ended too 
early (dishes are dirty and wet)
- Dirty or clogged filters. - The filters must not be dirty or clogged.
- Too little water in the dishwasher’s water system. - Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack.
- Drain hose incorrectly fitted.- The drain hose must be fitted correctly (for high mounted appliances, leave min. 200-400 mm from the lower edge of the 
appliance) - see Assembly instructions.
- High level of foam inside. - Repeat without detergent or wait until foam disappears.
...shows “F8 E1”
-Dirty filters.
- Clean the filters.
- Kinked drain hose.
- The drain hose must not be kinked.
- Syphon hose connection closed.
- The closure disk of the syphon hose connection must be removed.
After taking the above course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated.
RESET:Press the CANCEL/Off button.
Close the door.
Water drains automatically for up to 1 minute.
The appliance is now ready to be restarted.
Crockery and cutlery... Possible causes... Solutions...
...are not perfectly clean/have food residues
- Too little space between dishes (incorrect arrangement of the 
concave items in the rack).
- Arrange crockery so that items do not touch each other. Concave items (e.g. bowls, cups) must be arranged facing 
downwards in the rack.
- Too little detergent; detergent too old or incorrectly stored.
- If necessary, use more detergent, observing the manufacturer’s indications as regards dosage. Always store detergent in a 
dry place and do not store it for excessively long periods of time.
- Temperature not high enough for heavily soiled crockery.
- For heavily soiled crockery, select a wash program with a higher temperature (see table of programs - page 1).
- Loading of the dishwasher using lower and upper rack at the 
same time with “Half load/Multizone” option.
- If you select the “Half load/Multizone” option (if available), remember to load only 
the upper rack or only
 the lower rack to 
increase washing power and thus obtain optimum wash results.
- Frequent use of Eco 50°C.
- In the event of frequent use of the Eco 50°C program (if available), from time to time select the Intensive 70°C program (if 
available).
- Clogged spray arms, dirty filters or not fitted correctly.
- The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see page 5, “Maintenance and care“).
- Spray arms stuck impeded by crockery or cutlery.
- The spray arms must be able to turn freely and must not be impeded by crockery or cutlery.
 
						

							GB 
-7-
What to do if...
Crockery and cutlery... Possible causes... Solutions...
...salt indicator lit
- Use tablets for soft water.
- Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up.
...have deposits: regeneration salt residue
- Water too hard. - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water 
hardness”).
- Salt reservoir cap open. - Close the salt reservoir cap properly.
- Not enough rinse aid. - If you use a combined action detergent, try adding more rinse aid.
...are not dry
- Plastic containers dry badly.
- Synthetic materials do not dry well; if wet at end of cycle, wipe dry.
- Clean dishes left in dishwasher for a long time after end 
of cycle (e.g. when using “Delayed start” option).
- In this situation, the presence of drops of water on dishes and on the sides of the dishwasher is normal. 
Try releasing the door 5 minutes before removing the dishes.
- Incorrect arrangement of the concave items in the rack.
- Arrange crockery so that water does not collect in cavities.
- Incorrect dosage the rinse aid.
- Increase the dosage of rinse aid (see page 3, “Adding rinse aid”).
-Rapid program selected.
- The Rapid program 40°C / 45°C is intended for quickly washing lightly soiled dishes. If used for a full load of 
medium/heavy soiled dishes, the dishes may not dry completely. If so, select a standard-length program. For best 
results, open the door after the end of the program and wait 15 minutes before unloading the dishwasher.
...have discoloured plastic parts- Tomato/Carrot juice. - Tomato sauce, for example, can lead to discolouring of plastic parts. Powder detergent is recommended as 
it allows slightly higher doses to be used for improved whitening. Programs with higher wash temperatures 
should be used.
...opaque glasses, etc.
- Dishes unsuitable for washing in dishwashers (porcelain),
- Only use dishwasher-proof crockery and dishes.
...removable deposits on glasses- Usage of incorrect programs for glasses. - Dishes should be put together, to avoid touching each other. Do not put glassware together in baskets. 
Use suitable program for glass.
...glasses not sparkling- Not conform of glasses to washing in dishwashers 
(porcelain).- Some kinds of glass cannot be washed in the dishwasher.
...permanent deposits on glasses
-Rainbow effect.
- This phenomenon is irreversible. We recommend in future:
- Change the control of system of dosage of softener.
- Be careful – follow recommended detergent dosage.
- For combined action tablets see detergent producer’s recommendations.
...tea cups darken and dirt does not 
disappear after washing in dishwasher- Not known.
- This phenomenon is inevitable. Theine alters colours permanently.
...rust marks
- Pre-wash program not used.
- Salty or acidic food residues can cause rust marks even on stainless steel cutlery. To avoid this, always use 
the pre-wash program if the dishes are to be washed later.
...other marks
- Rinse aid dosage too low. - In the presence of marks, increase the rinse aid dosage (see page 3, “Adding rinse aid”).
- If you use a combined action detergent, possibly add more rinse aid.
...streaks
- Rinse aid dosage too high.
- In the presence of streaks, reduce the rinse aid dosage (see page 3, “Adding rinse aid”).
- If you use a combined action detergent which includes rinse aid, do not add any additional rinse aid.
...suds- Unsuitable dosage of detergent/rinse aid.- Only use the amount of detergent/rinse aid required, since excessive amounts can lead to excess suds.
 
						

							GB 
-8-
What to do if...
If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).
Before contacting our After-Sales Service, take note of the following:
- the description of the fault,
- the appliance type and model,
- the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:
Precautions and general recommendations
1. Packing
The packaging materials are 100% recyclable and marked with the recycling symbol  .
2. Removing the packaging and inspecting the contents
After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, 
contact a qualified technician or your local retailer. 
3. Before using the dishwasher for the first time
- The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
- This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may 
leave slight drips/water marks which will disappear with the first wash.
4. Energy and water savings
- Do not rinse crockery under running water.
- Always fully load the dishwasher before running it or select the “Half load/Multizone” option (if available).
- If ecological energy sources are available such as solar panel heating, heat pumps or centralised heating 
systems, the appliance may be connected to the hot water mains up to a maximum temperature of 60°C. 
Make sure the water inlet hose is of the correct type (“70°C Max” or “90°C Max”).
5. Child safety
- Keep the packaging materials out of the reach of children. 
- Children must not be allowed to play with the dishwasher. 
- Store the detergent, rinse aid and salt out of the reach of children.
6. Safety warnings
- The appliance is not intended for use by children or physically or mentally impaired persons, unless 
adequately supervised by a responsible adult capable of guaranteeing safe use of the appliance. 
- Do not operate the appliance in the open air. 
- Do not store flammable materials in close proximity to the dishwasher. 
- The water in the dishwasher is not potable. 
- Do not use solvents inside the dishwasher: risk of explosion! 
- Be careful when the door is open: risk of tripping!
 
- The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest 
objects on the open door or sit or stand on it.
- Sharp items that might cause injury (e.g. knives), must be placed in the cutlery basket with the sharp end 
facing downwards. Long-handled utensils must be arranged horizontally in the upper rack, with the sharp 
end facing away from the front of the appliance.
- Before cleaning or carrying out maintenance, disconnect the mains plug and turn off the water tap; also in 
the event of any malfunction.
- Repairs and technical modifications must be carried out exclusively by a qualified technician.
7. Resistance to frost
If the appliance is placed in surroundings exposed to the risk of frost, it must be drained completely. Turn off 
the water tap, remove the inlet and outlet hoses, and let all the water drain away. Make sure there is at least 
1 kg of dissolved regeneration salt in the salt reservoir, to protect the appliance from temperatures of up to 
-20°C. When the program resumes, an error message may be indicated (see page 6).
“F6  E2” - the appliance must remain at an ambient temperature of min. 5°C for at least 24 hours. 
After eliminating these faults, RESET the appliance (see chapter “What to do if...”).
8. Disposal
- The appliance is manufactured using recyclable materials. If you decide to scrap the dishwasher, it must be 
disposed of in compliance with local waste disposal regulations. Make it unusable by cutting off the power 
cord. To prevent situations of potential danger to children (e.g. danger of suffocation), break the lock of the 
door so that it can no longer be closed.
- This appliance is marked according to the European directive 2002/96/CE on Waste Electrical and 
Electronic Equipment (WEEE). By ensuring that this appliance is scrapped suitably, you can help prevent 
potentially damaging consequences for the environment and health. Unsuitable disposal of an appliance of 
this type as household waste could have detrimental effects on the environment. The symbol   on the 
appliance, or on documentation enclosed with the appliance, indicates that this product must not be 
treated as household waste, but must be delivered to the nearest collection centre for the recycling of 
electrical and electronic appliances. Disposal must be carried out in accordance with local environmental 
regulations for waste disposal. For further information on the treatment, recovery and recycling of this 
appliance, contact your competent local authority, the collection service for household waste or the shop 
where you purchased the appliance.
EC Declaration of conformity
This appliance has been designed, constructed and distributed in compliance with the safety requirements of 
EC Directives:   2006/95/CE, 89/336/CE, 93/68/CE and 2002/95/CE (RoHS Directive). 
Loading Capacity: 12 place settings.
The guarantee is not applicable if faults are caused by incorrect use of the appliance.Disconnect the mains plug
We reserve the right to make technical modifications.