Whirlpool Adg 555 Ix Instruction Manual

							19
Tension adjustment
of the door spring
【】Figure5
Tension adjustment of the door spring●
Connection of drain hoses●
The door springs are set at the factory to the proper tension for the outer door. If aesthetic
wooden panel are installed, you will have to adjust the door spring tension. Rotate the
adjusting screw to drive the adjustor to strain or relax the steel cable(see figure 5).
Door spring tension is correct when
the door remains horizontal in the
fully opened position yet rises
toaclosewiththeslightliftofa
finger.
È
rel ax
Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it
runintothesink,makingsuretoavoidbendingorcrimpingit.Usethespe ial
plastic support that comes with the appliance (figure 6). The free and of the hose
must be at a height between 400 and 1000mm and must not be immersed in water
to avoid the back flow of it. ATTENTION: The special plastic hose support must be
solidly fastened to the wall to prevent the drain hose from moving and allowing water
to spill outside the drain.c
Drain pipe connection
【Figure6】
 
						

							20
54
6 2
RUBBER
SCREWCOVE R
7
SCREW
CONE GEAR
5B5A
【】Figure 7
Dishwasher installation steps●
1 Install the furniture door to the outer door of the dishwasher using the brackets provided. Refer
to the template for positioning of the brackets.
2 Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to
tighten the left and right door springs. Failure to do this could cause damage to your dishwasher
(Illustration 2).
3 Connect the inlet hose to the cold water supply .
4 Connect the drain hose. Refer to diagram.(Figure 6)
5 Connect the power cord.
6 Affix the condensation strip under the work surface of cabinet. Please ensure the condensation
strip is flush with edge of work surface.
7 Place the dishwasher into position.
8 Level the dishwasher. The rear feet can be adjusted from the front of the dishwasher by turning
the screws on the left and right hand side of the cabinet (Illustration 5A). To adjust the front feet,
use a wrench and turn the front feet until the dishwasher is level (Illustration 5B).
9The dishwasher must be secured in place. There are two ways to do this:
A. Normal work surface-secure to the work surface by using two woodscrews ensuring the
dishwasher weight is not being hit by the surface (Illustration 6).
B. Marble or granite work top-secure the bracket to the side panel of the dishwasher and secure
the dishwasher to the furniture housing. Put the rubber cap over the screw (Illustration 7).
 
						

							Dishwasher must be level for proper dish rack operation and wash performance.
Place level on door and rack track inside the tub as shown to check that the
dishwasher is level.
level the dishwasher by adjusting the four leveling legs individually.
When level the dishwasher, please pay attention not to let the dishwasher tip over.
1
2
3
Illustration of feet adjustment
【】Figure 8
Check level
side to side
Level
to BackFro nt Ch eck
NOTE:
The maximum adjustment
height of the feet is 60 mm.
21
This appliance must be earthed. In the event
of a malfunction or breakdown, earthing will
reduce the risk of electric shock by providing a
path of least resistance for the electric current.
This appliance is equipped with a cord having an
equipment-earthing conductor and an earthing
plug. The plug must b e plu gged into an appropriate
outlet that is installed and earthed in accordance
with all local standards and requirements.Improper connection of the equ ipment-
grounding conductor ca n result in th e risk
of an electric shock. Check with a qualified
electrician or service representative if you
are in doubt whether the app lian ce is
properly grounded. Do no t modify the plug
providedwiththeappliance;Ifitisnotfit
for the outlet. Have a proper outlet installed
by a qualified electrician.„
„
Ensure the voltage and frequen cy of the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket which is earthed
properly. If the electrical socket to which the appliance must be connected is not
appropriate for the plug , replace the socket, rather than using a adaptors or the like as
they could cause overheating and burns.
Plea se look at the ra ting label to know the rating voltage and connect the dishwash er to the app ropriate power supp ly.
Use the required fuse 10 amp, time delay fuse or circuit breaker rec ommended and provide separate circuit serving
only this appliance.
WARNING!
For personal safety:
DO NOT USE AN EXTENSION CORD OR AN ADAPTER PLUG WITH THIS APPLIANCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE EARTHING
CONNECTION FROM THE POWER CORD.
 
						

							22
In order to avoid that there is more water staying in the inlet hose,
please close the hydrant after using.(For the models: no safety inlet hose.)
Positioning the Appliance
How to Drain Excess Water From Hoses
If the sink is 1000 higher from the floor, the excess water in hoses cannot be drained directly
into the sink. It will be necessary to drain excess water from hoses into a bowl or suitable
container that is held outside and lower than the sink.
Wat er O ut le t
Connect the water drain hose. The drain hose must be correctly fitted to avoid water leaks.
En sure that the water inlet hose is not kinked or s quashed.
The following things should be checked before starting the dishwasher.
Syphon Connection
The waste connection must be at a h eight of between 50 c m (minimum) and 10 0 cm (maximum)
from the bottom of the dish. The water drain hose should be fixed by a hose clip.
Start of Dishwasher
The content of this manual is very helpful to the users.
After installation, please make sure to keep this manual.
Extension Hose
If you n eed a drain hose extension, make sure to use a similar dra in hose.
It must be no longer than 4 metres; o therwise the cleanin g effect o f the dishwasher could be re duced.
1The dishwasher is level and fixed properly
2The inlet valve is open
3There is a leakage at the connections of the conducts
4The wires are tightly connected
5The power is switched on
6The inlet and drain hoses are knotted
7All packing materials and printings should be taken out from the dishwasher
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure
that it is fastened tightly in place.
If the water pipes are new or have not been used for an extended period of time, let the
water run to make sure that the water is clear. This precaution is needed to avoid the
risk of the water inlet to be blocked and damage the appliance.
The water supply to the appliance can also be connected to the household hot water
line (such as, central system, heating system),as long as it does not exceed a
temperature of 60 C. In this case, the wash cycle time will be shortened by about 15
minutes and the wash efficiency slightly reduced.
The connection must be made to the hot water line following the same procedures as
described in the section for the connection to the cold water line.
Position the appliance in the desired location. The back should rest against the wall behind it, and the sides,
along the adjacent cabinets or walls. The dishwasher is equipped with water supply and drain hoses that can
be positioned either to the right or the left sides to facilitate proper installation.
 
						

							F use b lown, or the
circuit breaker actedReplace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Spilled rinse-aidAlways wipe up rinse-aid spills immediately.
Hard water minerals
The affected items are
not corrosion resistant.
The lid of the softer
is loose
Asp ayarmis
k nocking a gain st
an item in a basketr
Items of crockery
are loose in the
wash cabin et
This may be caused
b y on-site insta llatio n
or the cross-section of
the piping. A programme was not
ru n after dishwashe r
salt was added.
Traces of s alt h ave
gotten into the wash cycle.To clean the interior, use a damp sponge with
dishwasher detergent and wear rubber gloves.
Ne ver u se any other clea ner than dishwashe r
detergent for the risk of foaming or suds.
Always run the quick wash programme .
without any crockery in the dishwasher and
without selecting the Turbo function (if present),
after adding dishwasher salt.
Check the lip .Ensure the fix is fine.
Interrupt the pro gram me, and rearr ange the item s
wh ich a re o bstructing the sp a y arm.r
Interrupt the pro gram me,
an d rea rran ge th e items o f cro ckery.
This has no influence on the dishwasher function.
if in doubt, contact a suitably qualified plumber.
Detergent with
colourant was usedMake s ure that the deterg ent is the one with out
colourant.
Improper detergent
Make sure the dishwasher is turned on and the door is
closed securely.
Check that the water supply is connected properly and
the water is turned on.
Ma ke s ure to clo se the do or properly an d latch it.
Make sure the power cord is properly plugged into the
wall socket. Power supply is not
turned on
Error code:E1;
Water pressure is low
Door of dishwasher
n ot pr operly closed.
Kink in drain hose
Filter clogged
Kitchen sink cloggedCheck drain hose.
Check coarse the filter
(se e se ction titled ) Cleaning The Filter 
Check the kitchen sink to make sure it is draining well.
If the problem is the kitchen sink not draining ,you may
need a plumber rather than a serviceman for dishwashers.
Use only the special dishwasher detergent to avoid
suds. If this occurs, open the dishwasher and let suds
evaporate. Add 1 gallon of cold water to the tub. Close
and latch the dishwasher, then Start the soak wash
cycle to drain out the water . Repeat if necessary.
Before Calling for Service
23
Te c h n i c a l
problems
General
problems
Noise
 
						

							The dishes were not
lo aded cor rectly.See notes in  Loading the Dishwasher Baskets .
Select a more intensive programme.
See Wash Cycle Table .
Use more detergent, or change your detergent.
Rearrange the items so that the sp ay can rotate freely.r
Clean and/or fit the filter combination correctly.
Clean the sp ay arm jets. See Cleaning the Spray
Arms.r
Use less detergent if you have soft water and select
a shortest cycle to wash the glassware and to get
them clean.
Use a mild abrasive cleane r to eliminate those ma rks.
Re-loading the dishes properly.
Load the dishwasher as suggested in the directions.
Increase the amount of rinse-aid/refill the rinse-aid
dispenser.
Do not empty your dishwasher immediately after
washing. Open the door slightly so that the steam can
escape. Begin unloading the dishwasher only once t
he dishes are barely warm to the touch. Empty the low
basket first. This prevents water form dropping off
dishes in the upper basket.
In short program the washing temperature is lower.
This also lowers cleaning performance. Choose
a program with a long washing time.
Water drainage is more difficult with these items.
Cutlery or dishes of th is type are not suitable for
washing in the dishwasher.The programme was
not powerful enough.
Not enough detergent
was dispensed.
Items are block ing
the path of spray arms.
T he filter combinatio n
inthebaseofwash
c abine t is not c lean or
is not correctly fitted.
This may cause
the sp ay arm jets
to get blocked.r
Combination of soft
water and too much
detergent.
Aluminum utensils
have rubbed against
dishes.
Dishes block
detergent cups.
Improper loading
Too little rinse-aid
Dishes are removed
too soon
Wrong program
h as been s elec ted
Use of cutlery with
a low-quality co ating
24
Unsatis
-factory
washing
result
Unsatis
-factory
drying
result
 
						

							25
Height : 820mm(adjustable+60mm)
Width : 445mm
Depth : 540mm
Voltage connected Load : see rating label
Water pressure: 0.04-1.0MPa
Hot water connection : max 60℃
Power supply: see rating label
Capacity: 9 Place settings