Whirlpool Adg 185 Instruction Manual

19
Tension adjustment
of the door spring
【】Figure5
Tension adjustment of the door spring●
Connection of drain hoses●
The door springs are set at the factory to the proper tension for the outer door. If aesthetic
wooden panel are installed, you will have to adjust the door spring tension. Rotate the adjusting
screwtodrivetheadjustortostrainorrelaxthesteelcable(seefigure5).
Door spring tension is correct when
the door remains horizontal in the
fully opened position yet rises
to a close with the slight lift...

20
54
6 2
RUB BER
SCREWCOVER
7
SCREW
CONE GEAR
5B5A
【Figure7】
Dishwasher installation steps●
.
.
.
.
6
7
8
1 Install the furniture door to the outer door of the dishwasher using the brackets provided. Refer
to the template for positioning of the brackets.
2 Adjust the tension of the door springs by using an Allen key turning in a clockwise motion to
tighten the left and right door springs. Failure to do this could cause damage to your dishwasher
(Illustration 2)
3 Connect the inlet hose to the cold water...

Dishwasher must be level for proper dish rack operation and wash performance.
Place level on door and rack track inside the tub as shown to check that the
dishwasher is level.
level the dishwasher by adjusting the four leveling legs individually.
When level the dishwasher, please pay attention not to let the dishwasher tip over.
1
2
3
Illustration of feet adjustment
【】Figure 8
Check level
side to side
Level
to BackFro nt Ch eck
NOTE:
The maximum adjustment
height of the feet is 60 mm.
21
Ensure the...

22
DO NOT USE AN EXT ENS ION CORD OR A N A DAPTER PLU G W ITH THIS AP PLIA NCE.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE FROM THE POWER CORD. EARTHING CONNECTION
Connect the cold water supply hose to a threaded 3/4(inch) connector and make sure that it is fastened tightly in place. If the water pipes are new or have not been used for an extended period of time , let the 
water run to make sure that the water is clear. This precaution is needed to avoid the
risk of the water in let to be blocked...

23
F use b lown, or the
circuit breaker actedReplace fuse or reset circuit breaker. Remove any other
appliances sharing the same circuit with the dishwasher
Spilled rinse-aidAlways wipe up rinse-aid spills immediately.
Hard water minerals
The affected items are
not corrosion resistant.
The lid of the softer
is loose
Asp ayarmis
k nocking a gain st
an item in a basketr
Items of crockery
are loose in the
wash cabin et
This may be caused
b y on-site insta llatio n
or the cross-section of
the piping. A...

24
WARNING!
If overfl ow oc curs, turn off the main water s upply before calling a service.
If there is water in the base pan because of an overfill or small leak,
thewatershouldberemovedbeforerestartingthedishwasher.
Longer inlet time.Fa ucets is n ot opene d, or water int ake is res tricted, o r water
pressure is too low.
Malfunction of temperature sensor or of heating element.
Sh ort c irc uit or b r ea k of te mp e r at ur e s e nso r
Op en c ircuit or b reak of te mpe rature sensor
Longer heating...

25
Height : 820mm(adjustable+60mm)
Width : 445mm
Depth : 540mm
Voltage connected Load : see rating label
Water pressure: 0.04-1.0MPa
Hot water connection : max 60
F
Power supply: see rating label
Capacity: 9 Place settings