Westinghouse Television TX-42F810G User Manual

							IMPORTANT INFORMATION
7
English
WARNINGS AND PRECAUTIONS
• Do not orient the LCD TV towards direct sunlight to reduce glare.
• If the LCD TV will not be used for a long period of time, unplug the unit and 
remove the batteries from the remote control.
• Avoid touching the display screen by hand or any object.
• Never remove the rear cover. The LCD TV interior contains high-voltage 
parts. You may be seriously injured if you touch them.
• Always handle the LCD TV with caution when moving it.
• Do not install the LCD TV in airtight compartments, or in areas where it can 
be exposed to water or high temperature.
• Ensure that the area around the LCD TV is clean and free of moisture.
• Do not place anything on the LCD TV that can hinder heat dissipation.
• Do not place naked flame sources, such as lighted candles, on or near the 
LCD TV.
• Do not place anything on the LCD TV that can cause liquid to splash on it 
(e.g. flower vase).
• Do not place heavy objects on the LCD TV, audio/video cables, or power 
cord.
• If the LCD TV emits smoke, abnormal noise, or a strange odor, immediately 
turn it off and contact the Westinghouse Service Center by:
– Logging on to www.wde.com.
– Contacting the Westinghouse Customer Service at (800) 701-0680.
– E-mailing us at [email protected]. 
						

							
IMPORTANT INFORMATION
8
English
ANTENNA INSTALLATION SAFETY
Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the LCD TV, be sure the 
antenna or cable system is grounded to prevent voltage surges and built-up static 
charges. Article 810 of the National Elec trical Code, ANS/NFPA 70, provides 
information on proper grounding of the mast  and supporting structure, grounding of 
the lead-in wire to an antenna discharge unit, connection to grounding electrodes, 
and requirements for the grounding electrode.
Antenna Grounding According to the National 
Electrical Code, ANSI/NFPA 70
Antenna lead in wire
Antenna discharge unit  
(NEC Section 810-20)
Grounding Conductors  
(NEC Section 810-21)
Grounding clamps
Power service grounding  
electrode system  
(NEC Art 250 part H)
Grounding clamps
Electric service  
equipment
NEC: National Electrical Code
Lighting
ZZZ
For added protection for the LCD TV during a lightning storm, or 
when it is left unattended and unused for long periods of time, 
unplug it from the wall outlet an d disconnect the antenna or cable 
system.  DO NOT  disconnect the antenna or the power cord during 
a heavy storm—lightning may strike while you are holding the 
cable cord, causing serious injury. Turn off the LCD TV and wait for 
the weather to improve.
An outside antenna system should not be located in the vicinity of 
overhead power lines or other electric light or power circuits, or 
where it can fall into such power lines or circuits. When installing an 
outside antenna system, extreme care  should be taken to keep 
from touching such power lines or circuits as contact with them 
might be fatal.
Power lines 
						

							
IMPORTANT INFORMATION
9
English
CLEANING THE LCD TV
• Make sure the LCD TV is turned off and the power cord is disconnected from the power outlet.
• Never spray or pour any liquid directly onto the screen or the 
case.
To clean the screen:
1Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other 
particles.
2If it is still not clean, apply a sma ll amount of non-ammonia, non-alcohol 
based glass cleaner onto a clean, soft,  lint-free cloth, and wipe the screen.
To clean the case:
1Wipe the case with a soft, dry cloth.
2If it is still not clean, apply a sma ll amount of non-ammonia, non-alcohol 
based, mild non-abrasive  detergent onto a clean, soft , lint-free cloth, then 
wipe the surface.
Dolby-Digital Notice
Manufactured under license from Dolb y Laboratories. Dolby and the double-D 
symbol are registered tradema rks of Dolby Laboratories. 
						

							
PACKAGE CONTENTS
10
English
PACKAGE CONTENTS
32” LCD TV UnitRemote Control (with 2x AAA batteries)
FavoriteMTSZ
Z
ZC.C.
TV
Video1
HDMI1
YPbPr1
PC
Video2
HDMI2
YPbPr2 ENT
DA
B
C
Vol Input
Ch
Enter
RMT-11
LCD TV BaseQuick Connect Guide
Power CordWarranty Card
User ManualWarranty Brochure
Product BrochureM4 x L10 mm Screw for Base 
						

							
CONTROL PANEL
11
English
CONTROL PANEL
Power
Source Menu
Volume
Channel
U SBL RH
DM
ICO MPON ENTPC  
/  V G AP
C
 A
UDIOS
PD
IF
 O
U
TY
Pb P
r
L R
2
3
1
4
5
ItemDescription
1. MenuDisplay the LCD TV setup screen.
2. Volume +/-During playback, adjust the volume; in 
a menu screen, select an item.
3. Channel +/-During TV viewing, adjust the channel; 
in a menu screen, select an item.
4. SourceSelect the video input source; in a 
menu screen, execute a command.
5. PowerToggles the power on and off. 
						

							
TERMINALS
12
English
TERMINALS
USBL RH
D M
IC
O
M P
O NEN
TPC
 /  
V
G
APC
 A
UDIOS
P
D
IF
 O
UTY
Pb P
r
L R
L
R
HDMI
COMPONENT
AUDIO
PC / VGA PC AUDIO
SPDIF OUT Y
PbPr
YPbPr
LR
LR
AV1LR
USB
AV 2
L
R
HDMI
1281257
13
14
102116943
ItemFunction
1. AC inConnect the power cord from this outlet to a 
power source.
2. HDMI Connect to an external video device such as a 
DVD player, game system,  cable, or satellite box.
3. PC/VGAUsing a 15-pin VGA cable, connect to a computer 
or other device with a VGA output.
4. PC Audio inConnect to the audio out port of a computer.
5. AUDIO OUT-STEREOConnects to the AUDIO (R/L) input jacks on 
external AV equipment.
6. SPDIF (optical) audio 
outConnect this output to an external digital audio 
receiver.
7. YPbPr inputConnect an external video device with component 
output to these jacks.
8. YPbPr audio inputConnect an external audio source.
9. Composite video inputConnect to an external video device with an 
analog signal such as a VCR.
10. AV audio inputConnect this input to an external audio source.
11. TV tunerConnect the LCD TV to an antenna or cable 
service.
12. USB Service portFor service only.
13. Composite video  input AV2Connect to an external video device with an 
analog signal such as a VCR.
14. AV2 Audio inputConnect this input to an external audio source. 
						

							
REMOTE CONTROL
13
English
REMOTE CONTROL
ItemDescription
FavoriteMTSZ
Z
ZC.C.
TV
Video1
HDMI1
YPbPr1
PC
Video2
HDMI2
YPbPr2 ENT
DA
B
C
Vol Input
Ch
Enter
RMT-11
1
7
10
14
17 3
5
2
4
6
20
22 21
23
24
26 2
527 9
19 13
16 8
11
12
1
5
18
1. Mute  Mute the sound. Press it again to 
toggle the sound back on.
2. Power Toggle the TV power on and off.
3. Backlight Adjust the LCD screen backlight.
4. MTSNot supported.
5. CCToggle the closed caption display on 
and off.
6. Sleep 
zZzSet the sleep timer for the LCD TV to 
turn off automatically.
7. Channel keysKey in the channel number.
8. Favorite 
Switch to the favorite channels. See 
page 23 for details on how to save a 
new favorite channel.
9. Enter ENTExecute a channel entry.
10. Menu Display the LCD TV setup screen.
11 .  R e t u r n  Switch to a previously bookmarked 
channel.
12. Arrow keysNavigate through the on-screen 
menu.
13. Enter Execute a command.
14. GNot supported.
15. Info 
Display the input so urce or channel 
information as well as the system 
date and time.
16. InputSelect the video input source.17. Vol +/-Ajust the system volume.
18. Ch  / Change the current TV channel.
19. Aspect ratio Select the video display format.
20. YPbPr1Enable YPbPr as the input source.
21. TVEnable TV or HDTV as the input 
source.
22. HDMI1Enable HDMI1 as the input source.
23. Video1Enable Video1 or video2 as input.
24. YPbPR2Not supported.
25. PCEnable VGA as the input source.
26. HDMI2Enable HDMI2 as the input source
27. Video2Enable S-Video as the input source. 
						

							
REMOTE CONTROL OPERATION
14
English
REMOTE CONTROL OPERATION
INSTALLING THE REMOTE CONTROL BATTERIES
CAUTIONS:
• Only use AAA batteries.
• Do not mix new and old batteries. This may result in cracking or leakage, 
which may pose a fire risk or lead to personal injury.
• Insert batteries according to the (+) and (-) markings. Inserting the batteries incorrectly may result in  cracking or leakage, which may pose a 
risk of fire or lead to physical injury.
• Dispose of used batteries in accor dance with local laws and regulations.
• Keep batteries away from children and pets.
• When the remote control will not to be used for an extended period, 
remove the batteries.
1Remove the battery cover.
2Insert the batteries. Make sure the  (+) and (–) marks on the batteries match 
those inside the compartment.
3 Re-attach the battery cover.
REMOTE CONTROL TRANSMISSION RANGE
Transmission range depends upon the reception angle. The range of coverage is 20° 
horizontal/vertical at a distance of 10 feet from the LCD TV.
FavoriteMTSZ
Z
ZC.C.
A
B 
						

							
LCD TV BASE
15
English
LCD TV BASE
CAUTION:The LCD TV unit may be too heavy for one person to lift. If this is the case, 
make sure to ask for assistance in handling the LCD TV to prevent 
physical injury and/or damage to the unit.
INSTALLING THE LCD TV BASE
1Open the LCD TV carton box.
2Remove the LCD TV base.
3Remove the plastic bag.
4Remove the two top carton stabilizers from the LCD TV.
5Remove the protective plastic covering the LCD TV.
6Grasp the two sides of the LCD TV and then pull it out of the carton box.
7Remove the two bottom carton stabilizers from the LCD TV.
8Lay the LCD TV on a clear, flat, and stable surface.
9Align the base to the bottom side of  the LCD TV and use one M4 x L10 mm 
screw to secure it.
U SBA V
 
2U
SBA V
 
2
10
Carefully orient the LCD TV in an upright position.
U
SBAV 2
USBL RH
DM
ICO M P
O N
EN TPC  
/
 V G AP
C  A UDIOSPD I
F  
O UTY
Pb P
r
L RUSBLRH
DM
ICO M P
O N
EN TPC  
/
 V G AP
C  A UDIOSPD I
F  
O UTY
Pb P
r
L R 
						

							
LCD TV BASE
16
English
REMOVING THE LCD TV BASE
If you intend to repack the LCD TV unit (for shipping or storage) or you want to 
change the installation to a wall mount option, you must first remove the LCD TV 
base.
1Turn off the LCD TV and all connected devices.
2Disconnect the power cord from the LCD TV.
3Disconnect all signal cables from the I/O port terminals.
4Lay the LCD TV on a clear, flat, and stable surface.
U
SBA V
 
2
U S
B
L RH
DM
ICO
M PO N
EN
TPC  
/ 
V G AP
C
 A
UDIOS PD I
F  
O UTY
Pb Pr
LR
5
Remove the screw securing the base to the LCD TV.
6Detach the base from LCD TV.
U
SBA V 2U
SBA V 2
7 Pack the screws you removed in st ep 5 together with the LCD TV base for 
future reassembly.