Westinghouse LD-425 Series Tv Users Manual

							LED TV BASE
16
English
REMOVING THE LED TV BASE
If you intend to repack the LED TV unit (for shipping or storage) or you want to 
change the installation to a wall mount option, you must first remove the LED TV 
base.
1Turn off the LED TV and all connected devices.
2Disconnect the power cord from the LED TV.
3Disconnect all signal cables from the I/O port terminals.
4Remove the M5 x 16 screw securing the base to the desk.
5Lay the LED TV on a clear, flat, and stable surface.
6Remove the screws securing the base to the LED TV.
7Detach the base from LED TV.
8Pack the screws you removed in step 4 and 6 together with the LED TV base 
for future reassembly. 
						

							ANTENNA CONNECTION
17
English
ANTENNA CONNECTION
OUTDOOR ANTENNA CONNECTION
CABLE TV (CTV/DTV) CONNECTION
The unit has a TV tuner (75 ohm coaxial cable connector) located on the rear I/O 
panel for easy cable hookup. When connecting the 75 ohm coaxial cable to the unit, 
screw the 75 ohm cable to the TV tuner. Some cable TV companies offer premium 
pay channels. Since the signals of these channels are scrambled, a cable TV 
converter/descrambler is usually provided to the subscriber by the cable TV 
company. This converter/descrambler is necessary for normal viewing of the 
scrambled channels. (Set your TV to channel 3 or 4. Typically one of these channels 
is used. If a channel is unknown, consult your cable TV company.) For more specific 
instructions on installing cable TV, consult your cable TV company. One possible 
method of utilizing the converter/descrambler provided by your cable TV company is 
explained below.
NOTE:
The F-type connector should be finger-tightened only. 
When connecting the RF cable to the LED TV, do not 
tighten F-type connector with any tool. If tools are 
used, it may cause damage to the LED TV (e.g. 
breaking of internal circuit).
Cable TV lead in
VHF, UHF or VHF/UHF 
combination antenna
75 ohm coaxial cable (round)
300 ohm twin-lead (flat)300-75 ohm ADAPTER 
(Not supplied)
Separate VHF/UHF Antenna
VHF Antenna UHF Antenna
300 ohm twin-lead 
300 ohm twin-lead 
75 ohm coaxial cable COMBINER 
(Not supplied)Home Antenna 
terminal (75 ohm)RF IN
IN OUT 
						

							EXTERNAL DEVICE CONNECTIONS
18
English
• A position on the RF switch (not supplied) – You can view all unscrambled 
channels by using the TVs channel keys.
• B position on the RF switch (not supplied) – You can view the scrambled 
channels via the converter/descrambler by using the converters channel 
keys.
EXTERNAL DEVICE CONNECTIONS
You can enjoy picture and sound by connecting various audio-video devices to the 
terminals located on the rear and side I/O panels of the LED TV.
• TV cable input – You can use a commercially available audio/video cable.
• Component (YPbPr) input – Picture can be displayed only when a 480i, 
480P, 720P or 1080i signal is received.
• HDMI input – Picture can be displayed only when a 640 x 480, 480P, 720P 
or 1080i signal is received. When you connect to the HDMI terminal with a 
DVI-HDMI conversion cable, there is a possibility that the picture may not 
display correctly.
• Audio output – You can output audio signals from the LED TV set through 
the analog audio out and SPDIF terminals.
IMPORTANT:
• Turn off the LED TV first before connecting an external device to prevent 
any possible damage or physical injury.
• For more information about external device connections, see the operation 
manual of the external device you wish to connect to the LED TV.
• Make sure that the correct cables are connected to each terminal. 
Improper cable connections may cause damage to the LED TV.
RF switch (not supplied)
Cable TV line A
B IN
OUT
Tw o - s e t 
signal 
splitter 
(Not 
supplied)
Cable TV 
converter/descrambler 
(Not supplied) 
						

							EXTERNAL DEVICE CONNECTIONS
19
English
The following diagram shows the external device connections.
VGAY
L
R
AUDIO INTUNERDC IN
SPDIF HDMI 1 HDMI 2 USB
L
R
Antenna cable / 
Cable TV line
Antenna /
Cable system
PC
AUDIO OUT
AUDIO OUT
3.5 mm stereo mini jack cable
RGB cable
Audio cable
SPDIF 
cable
HDMI-HDMI 
cableDVI-HDMI 
cable
DVD player
with an HDMI 
terminal
AC to DC adapter Power outlet
Home video 
game system
CamcorderVCR
DVD player
Digital TV tuner
Composite AV cable
DVD player
with a DVI 
terminal Audio amplifier
Audio amplifier 
						

							POWER CONNECTION
20
English
POWER CONNECTION
CONNECTING AC POWER
Connect the power cord of the AC to DC adapter to the LED TV then to a proper AC 
outlet.
INITIAL SETUP
Press  on the control panel or on the remote control to turn on the LED TV. Select 
the desired language and your time zone to use the Setup Wizard. The Setup 
Wizard will guide you on how to scan and store channels.
IMPORTANT:The LED TV is designed to be powered via an AC to DC adapter. Use 
ONLY the AC to DC adapter included in the package. Turn off all 
connected devices before plugging the adapter into the power outlet.
MENU INPUTVOL
CH
FavoriteMTSZZ
ZC.C.
A
B 
						

							BASIC OPERATIONS
21
English
BASIC OPERATIONS
TURNING THE POWER ON AND OFF
Turning on the power
Press  on the control panel or on the remote control to turn on the LED TV.
Turning off the power 
Press  on the control panel or on the remote control to turn off the LED TV. The 
LED behavior will depend on the enabled Power settings.
ADJUSTING THE VOLUME
Vo l u m e
Press Vo l + to increase the volume; press Vo l -  
to decrease the volume.
Mute
Press  to turn off the sound. The mute icon 
appears on the screen. Press again to turn on 
the sound.
LED indicatorOperation
Turns from none to red.Turn the power on.
Turns from red to none.Turn the power off.
NOTES:
• If you are not going to use the TV for a long time, be sure to disconnect the 
power cord from the wall outlet and remove the batteries from the remote 
control.
• In standby mode, a small amount of electricity is still consumed even when 
the power is turned off.
MENU INPUTVOL
CH
FavoriteMTSZZ
ZC.C.
A
B
FavoriteMTSZZ
ZC.C.
TV Video1 HDMI1 YPbPr1VolInput
Ch
Mute
Vo l u m e 
						

							BASIC OPERATIONS
22
English
CHANGING CHANNELS
Follow the instructions below to change channels.
Using the Ch  /  Buttons
Browse channels
To browse through the available channels, press Ch  /  on 
the remote control or on the control panel.
Using the Channel Keys
Selecting channel
To change to a certain channel, key in the channel number using 
the channel keys and press ENT.
 
Selecting digital channel
To select a digital channel, key in the digital channel number using 
the channel keys and the • key, then press ENT.
Using the Favorite Keys
Selecting favorite channels 
To select a favorite channel, press the Favorite button (A, B, C, or 
D) corresponding to the preferred channel.
Saving a channel as a favorite
1Switch to the channel you want to add as a favorite.
2Press and hold the Favorite button which you want to add 
the current channel to for 3 seconds.
3The Channel Saved message appears to confirm the new 
favorite channel item.
SELECTING THE INPUT SOURCE
There are two ways to select the video input source.
Using the Individual Input Keys
TV, PC, Video, YPbPr, HDMI Keys
Press any of the following remote control keys to change the input 
source: TV, PC, Video1, Video 2, YPbPr1, YPbPr2, HDMI1, or 
HDMI2.
TV Video1 HDMI1 YPbPr1VolInput
Ch
Favorite
ENTDA
B
C
FavoriteMTSZZ
ZC.C.
ENTDA
B
C
TV Video1 HDMI1 YPbPr1
PC Video2 HDMI2 YPbPr2 
						

							BASIC OPERATIONS
23
English
Using the Input Key
Select source using Input Key
1Press Input.
2A list of supported video sources is displayed.
3Press  /  to select the preferred source.
4Press  to switch to the selected input source.
ADJUSTING THE DISPLAY FORMAT
The input source can sometimes affect the way images are displayed on-screen. 
You can adjust the display format to view the image properly.
Format Options
Press  repeatedly to toggle the display format. As you toggle 
each option on, the actual display will change accordingly. The 
available options are:
•Standard: Picture is displayed in its original size.
•Fill: Picture is displayed to cover the entire screen.
•Overscan: Picture is scaled down to fit the display area.
•1:1 Mode: Matches the incoming resolution exactly to the 
pixels without any scaling.
ADJUSTING THE LED BACKLIGHT
Different viewing conditions can affect the quality of the display. You can adjust the 
LED backlight to suit the current viewing condition.
Backlight options
Press  repeatedly to toggle the Backlight mode. The available 
options are: Bright Room, Medium Room, and Dark Room.
TV Video1 HDMI1 YPbPr1VolInput
Ch
TV Video1 HDMI1 YPbPr1
PC Video2 HDMI2 YPbPr2VolInput
Ch
FavoriteMTSZZ
ZC.C.
A 
						

							SETUP MENUS
24
English
SETUP MENUS
SETUP MENU OPERATION
Use the setup menus to configure the various operational settings of the LED TV.
Displaying the setup menu screen
Press  on the remote control or MENU on the control panel to display the setup 
menu screen.
Navigating the setup menu screen
Use the buttons on the remote control or on the control panel to navigate through 
the menu screens.
ActionRemote ControlControl Panel
Displays or closes the menu bar.MENU
• Select and display a primary 
menu.
• Adjust sub-menu options.  /   then Volume +/- then 
INPUT
• Select and display a sub-menu.
• Select a sub-menu or a sub-
menu option. /   then Channel +/- then 
INPUT
• Returns to the primary menu tab 
from a sub-menu screen.
• Returns to the previous screen.MENU
Applies the selected menu setting.INPUT
SPDIF
--Y
L
R-L
R VGA AUDIO INTUNERDC IN
HDMI 1 HDMI 2 USB
MENU INPUTVOL
CHEnter 
						

							SETUP MENUS
25
English
PICTURE
Use the Picture sub-menus to configure the display quality.
Press  on the remote control or MENU on the control panel to display the setup 
menu screen then select Picture to display the Picture sub-menu. The following 
options are available: Brightness, Contrast, Saturation, Video Presets, Sharpness, 
Color temperature, Hue, and Reset.
Brightness
Use Brightness to adjust the luminance level.
Adjusting Brightness
1  Use the  /  keys to select Brightness and press  .
2  Press the  /  keys on the remote control to adjust the brightness level.
3  Press  to save and exit the screen.
Contrast
Use Contrast to adjust the brightness to darkness ratio.
Adjusting Contrast
1  Use the  /  keys to select Contrast and press  .
2  Press the  /  keys on the remote control to adjust the contrast level.
3  Press  to save and exit the screen.
Brightness
Contrast