Westinghouse Ew39t4lz Users Manual

							9 Introduction
Installing Batteries
1. Open the battery compartment cover on the back of the remote control.
2. Insert two 1.5V AAA size batteries observing the polarity markings inside the battery 
    compartment. Don’t mix different types or used batteries with new ones.
3. Close the cover.
- The remote control should be operated within 23 feet(7m) and 300 to the left and right of the 
       IR Receiver on the front of the TV.
     - Used batteries should be disposed properly.
 
						

							10
First Time Installation
First Time Installation
The following pictures will appear on the screen when the TV is turned on for the first time.
1. Select the OSD menu language by
    buttton, and press OK/ENTER button to 
    enter the next menu.
2. Select the Time Zone by           buttton, then 
    select Next item by            button and press 
    OK/ENTER button to enter the next menu.
3. Select the power on mode by            buttton, 
    and press OK/ENTER button to enter the 
    next menu.
4. Select the Antenna or coaxial cable input
    connect mode by            buttton, and press 
    OK/ENTER button to enter the next menu.Note:
Home mode --- Power saving mode.
Retail mode --- Normal mode.
Note:
* Cable Box or Satellite Box--- If you want
  using the signals from the cable box or 
  satellite box, please select this item and
  press OK/ENTER button to setting.
* Game, Blu-Ray, DVD or other player --- 
  If you want using the signals from the 
  Game, Blu-Ray, DVD or other player, 
  please select this item and press OK/
  ENTER button to setting.
 
						

							11
First Time Installation
6. Select Next item by            button and press 
    OK/ENTER button to enter the next menu.
7. Select Next item by            button and press 
    OK/ENTER button to enter the next menu.
8. Enter the code by the number buttons on
    the remote control to start the auto channel
    search.
5. Select the Antenna [ATSC] or Cable mode by            buttton, and press OK/ENTER button 
    to enter the next menu.
9. The auto searching may take a few minutes 
    to complete. *6. The auto searching may take a few 
     minutes to complete.
Model: XXXXXXX
Serial No: XXXXXXXXXXX
Channel Scan Type: ATSC
 
						

							 button to select the function item, press           button to adjust/setup,
12
Power on/off
1. Connect to the power supply with the power cord, and turn on the switch.
2. -To turn on the TV
     Press POWERbutton on the TV or remote control.
   -To turn off the TV
     Press POWER button on the TV or remote control.
Input Source select
PressINPUT     button on the    TV set or remote control to display input 
source menu, and use CH+/-button on the TV set or 
$0
%!button
on remote control to select the input source, press OK button on the
remote control to enter.
Note: Before you select the input source, make sure the 
connections are prepared.
Basic OSD Menu operation
Use /
$
/

%

$

% 
% button to select the main menu, and press OK button to enter the submenu.Use /

$

% button to select.
In the submenu, use  /
$
%
or press   button to enter the submenu.
* (Press MENU button to return to the upper menu.)
* (Press EXIT button to exit the menu display.)
Main menu
Picture
Sound
Channel
Parental
Setup
Others
Submenu
(Picture menu
for example)
Guide - This guide shows the keys (buttons) on the remote 
control for selecting the items to setup in the OSD menu.
PressMENUbutton to display the OSD menu as below:
Basic Operation
Basic Operation
Press OK button
 
						

							OSD Menu
13
1. Picture menu
Description
Picture mode: Select between Dynamic,  Standard, 
Movie and User.
You may select the picture mode directly by pressing 
the PICTURE button on the remote control. Picture Settings:Press       button to enter the Picture Settings menu.
Screen Size:Select the displaying mode of the picture between Wide, Cinema, Zoom, Normal,
Just Scan, Standard, Fill, and Over scan.
PC Settings: If the video input signal comes from your PC, you may adjust the Vertical Position, 
Horizontal Position, Clock, Phase or even perform an Auto adjustment. Contrast:Control the difference between the bright and 
dark regions of the screen picture. Brightness: Adjust brightness of the picture.
Color: Adjust color of the picture.
Tint:Control the fresh tones to make them appear natural.
Sharpness:Set the amount of fine detail in the picture.
Color Temp.: Select between Normal, Cool and Warm.
Note: when select the "Standard", the 
machine is in energy-saving status.
OSD Menu
Auto Adjust: Press OK button to setup the parameter of 
the screen automatically.
Clock: Adjust the pixel clock frequency, until the image 
size is maximized for the screen.
H/V Position: Adjust the transverse/vertical position of 
the screen.
Phase: Adjust the phase of the ADC sampling clock 
relative to the sync signal, until a stable image is obtained.
Reset: Press OK button to reset the settings.
 
						

							OSD Menu
14
Dynamic Contrast: Activate or deactivate the Dynamic.
Contrast funciton.
Film Mode: Activate or deactivate the Film Mode.
Noise Reduction: If the broadcast signal received is 
weak, you can select the DNR option to reduce the video 
noise level between Off, Low, Medium and High.
MPEG Noise Reduction: Select the MPEG Noise 
Reduction option to reduce the picture noise level 
between Off, Low, Medium and High. Advanced Picture Settings:Press       button to enter the Advanced Picture Settings.
OSD Menu
 
						

							OSD Menu
15
2. Sound menu
Description
Sound Mode: Select your desired picture mode as
follow: Dynamic, Standard, Soft and User.
You may select the sound mode directly by pressing
the SOUND button on the remote control.
Bass:Low frequency intensity.
Treble:High frequency intensity.
Balance:Left and right stereo audio channels balance.
Surround Mode: Activate or deactivate the Surround function.
OSD Menu
Sound Settings:Press       button to enter the Sound Settings menu.
AVL: Activate or deactivate the Auto Volume Limited function.
Analog Sound: Select the Analog Sound mode between Stereo, Mono and SAP.
Digital Sound: Select the Digital Sound laguage.
Digital Audio Output: Select the Digital Audio Output mode between PCM, RAW and off.
Equalizer Settings: Press       button to enter the Equalizer Settings menu.
Use     /     button to select the item, and use     /     button Use     /    button to select the mode between User, Off,
Rock, Pop and Jazz.
You could press      button to enter the bottom item to
adjust the equalizer bu yourself when you select
the User mode.
to adjust. You could come back to the Mode selecting
item by pressing       button.
 
						

							OSD Menu
16
Description
3. Channel menu
Channel List: Display the channel list.
Favorite List: Display the favorite channel list.
Channel Settings: Press > button to display the Channel Settings menu.
Signal Type: Allow you to select antenna between Air, Cable and QAM.
Auto Channel Search: Press OK button to start auto channel search.Press                   button to select the item, and press OK 
button to change the setting.
OSD Menu
If you select “Cable” as input signal in Signal Type item, 
you can press     button to search the analog channels 
automatically. The receivable channels will be stored 
automatically. When searching channels, press MENU
 to stop.µ µ

%

%
If you select “Air” as input signal in Signal Type item, you
can press     button to search the channels automatically.
The receivable channels will be stored automatically.
When searching channels, press MENU to stop.
NOTE: It will take a while to auto scan in NTSC or ATSC
mode, please wait patiently.
 
						

							OSD Menu
17
OSD Menu
If you select “QAM” as input signal in Signal Type item, you can press     button to search the 
channels automatically. The receivable channels will be stored automatically. 
When searching channels, press MENU to stop.µ
%
1. Select Next item by            button and press 
    OK/ENTER button to enter the next menu.
2. Select Next item by            button and press 
    OK/ENTER button to enter the next menu.
3. Enter the code by the number buttons on the
    remote control to start the auto channel
    search.
NOTE: It will take a while to auto scan in NTSC or ATSC mode, please wait patiently.
Model: XXXXXXX
Serial No: XXXXXXXXXXX
Channel Scan Type: QAM
 
						

							OSD Menu
18
4. Parental Control menu
OSD Menu
Description
V-CHIP:Press     button to enter the V-CHIP menu.
You must enter the password to gain access to the Parental Control menu. The default password
 is 0000. You may modify the following options:
TV Rating:Use             buttons to select the desired rating and press      button to block  Movie Rating: The Movie rating (MPAA) is used for 
original movies rated by the Motion Picture Association
of America (MPAA) as broadcasted on cable TV and 
not edited for television.
Use             button to select  G, PG, PG-13, R, NC-17 
or X.
$0
% 
$0
%
%
G: General Audiences. Movie is appropriate for all ages.
PG: Parental Guideance Suggested. May contain material not 
suited for younger viewers.
PG-13:Contains content that may not be appropriate for viewers 
under the age of 13.
R: Restricted. Contains adult content, no one under 17 admitted 
without parent.
NC-17: No one 17 and under admintted.
X: Adults only.
US V-CHIP: Press      button to enter the US V-CHIP menu.
or unblock rating.