Vivitek Projector H9080fd User Manual

1
insTallaTion
3.5 Turning on the Power
Press the ON  button on the remote control to turn on the H9080FD.  
The power LED indicator flashes green to indicate that it is warming up.\
 
When the projector is ready for use, the LED indicator turns off, and th\
e projector lights.
3.6 Changing the OSD Language
The H9080FD can display the menus in  English, Español, Français, Deutsch, Nederlands, Italiano, 繁體中文, and 简体中文.
Enter the OSD, select Language in SETUP menu, then press the  or  buttons to...



3.8 Lens Adjustments
The H9080FD gives you a great deal of control over the picture size, pos\
ition and focus.
Focus
To focus the projected image, grasp the 
lens by the front ring and rotate it.
Focus Ring
Zoom
To make the picture smaller (zoom out) or 
larger (zoom in), rotate the zoom ring in the 
appropriate direction..
Zoom Ring
Zoom In
Zoom out
insTallaTion 



Lens Shift
To access the lens shift controls:
Loosen the two screws located at the 
rear side and underneath of the projec-
tor as shown in the figure at the right.
Slide the center portion of the top cover 
backward to expose the holes for lens 
shift.
 
 
 
 
 
 
 
 
 
Vertical Lens Shift: To shift the projected 
image vertically, insert the provided hex 
wrench into the hole at the top of the pro-
jector (directly above the lens). Then, turn 
the wrench as shown to shift the lens in the...

4

4.1 Selecting an Aspect Ratio
Press the aspect ratio () button to select the appropriate aspect ratio for the type of program\
 material being 
viewed.
4.2 Selecting An Input Source
When you turn on the  H9080FD, it switches to the last selected 
input and looks for a valid signal. 
Use these buttons on the remote control to select an input source 
directly. 
4.3 Using the On-Screen Menus
Press the MENU button on the remote control or system keypad to display \
the Main Menu. 
There are five...

5

GENEAL
Source SelectHDMI 1, HDMI 2, RGB, Comp 1, Comp 2, Video, S-Video, SCART
Menu PositionTop Left, Top Right, Bottom Left, Bottom Right, Center
PIP SelectOff, HDMI 1, HDMI 2, RGB, Comp 1, Comp 2, Video,  S-Video, SCART
PIP PositionTop Left, Top Right, Bottom Left, Bottom Right, PBP, Split
MemoryRecall MemoryUser1, User2, Default
Save SettingsUser1, User2
Blank ScreenLogo, Black, Blue, White
Logo DisplayOn, Off
Auto SourceOn, Off
Test PaternOn, Off
Blue OnlyOn, Off
IMAGE
Aspect Ratio16:9,...

6

GENERAL
The H9080FD GENERAL Menu, shown in Figure 4-2, provides access to the most commonly-used projector functions.
Figure 4-2: H9080FD GENERAL Menu
Source Select: To select a video source, press  or  to highlight Source Select, then press ENTER. This dis-
plays the Source Select submenu, shown in Figure 4-3. 
Figure 4-3: Source Select Sub-Menu
•
operaTion 

7

Menu Position: Select Menu Position from the GENERAL menu to change the OSD menu positi\
on.  
The default setting is “” (top left). 
PIP Select: To select a Picture in Picture source, press  or  to highlight PIP Select, then press ENTER.  
This displays the PIP Select sub-menu.  
The default source selection is Off. All sources that are not available \
(refer to Source Enable on page 49) are grayed out.
Figure 4-4: PIP Select Sub-Menu
PIP Position: Press  or  to select the on-screen PIP...



Top Left: This places the PIP source into a 644x362 designated image are\
a at the top left of the screen.
Top Right: This places the PIP source into a 644x362 designated image ar\
ea at the top right of the screen.
Bottom Left: This places the PIP source into a 644x362 designated image \
area at the bottom left of the screen-
safe area of the DMD.
Bottom Right: This places the PIP source into a 644x362 designated image\
 area at the bottom right of the 
screen-safe area of the DMD.
PBP...



Recall Memory: Select Memory from the General menu, and then press Enter to activate \
Recall Memory.  
Use the  or  buttons to select the modes: User-1, User-2 or Default.
Save Settings: Select Memory from the General menu, and then press  to highlight Save Settings.  
Use the  or  buttons to select the modes: User-1 or User-2.
Figure 4-7: Memory Sub-Menu
Blank Screen: Select Blank Screen from the GENERAL menu to choose the color of the bl\
ank screen that appears 
when no source signal is...

40

IMAGE
The H9080FD IMAGE Menu, shown in Figure 4-8, to perform image adjustments.
Figure 4-8: H9080FD IMAGE Menu
NoteThe PIP function must be disabled before you change the aspect ratio.
Aspect Ratio: To change the aspect ratio (size and shape) of the projected image, pr\
ess  or  to highlight 
Aspect Ratio. Use the  or  buttons to select the appropriate aspect ratio for your screen size, in\
stalled lens con-
figuration and the type of program material being viewed, then press ENT\
ER; refer to...