Vivitek Projector H8030 User Manual

							31
Overscan: Some television programs are produced based on the assumption that older\
 
television sets may not display the outer edges of the broadcast picture\
 area. Overscan 
effectively hides these inactive, outer edges of the image. Choose one of the following:
•  Off: This setting leaves the image as-is.
•  Crop: This setting adds a mask all around edges of the source active image equal to  
  2.5%.
•  Zoom: This setting adds a factor to the scaling of the source active image so that the  
  vertical and horizontal resolutions are 105% of the size determined by the aspect ratio  
  function. Anything outside of the original image area is removed.
Input Select:  This function is same as the hotkey which on Remote controller. You can use 
Remote controller or this function to select the correct input source
To select a video source, from Main Menu use  ▲
 or
 ▼
 to highlight Input Select, then press 
Enter, use  ▲
 or
 ▼
 to highlight the desired source, then press ENTER. 
Resync:  If the projected image becomes unstable or degraded, press  ▲
 or
 ▼
 to highlight 
Resync, then press ENTER. It also changes any Fine Sync setting for this\
 timing to the 
default setting.
H8030 Home Theater Projector - User Manual  
						

							32
OSD Introduction – ADVANCE
MAINSERVICELANGUAGECONTROLSYSTEMADVANCED
Menu = Exit Menu Select   Scroll  
Color Space
Vi
deo Standar d
Gamma
Color  Temperature
Color Gamut
BrilliantColor
Adaptive Contrast
RGB  Adjust
Fine Sync Auto 
YPbPr  YCbCr RGB-PC RGB-Video
Auto  NTSC  PAL  SECAM
CR T  Film  Video  BRIGHT  Graphics
5500K  6500K  7500K 9300K
Auto  REC709  SMPTE-C EBU Native
On    Off
On    Off
   Enter
   Enter
Color Space: Select Color Space from the Advanced menu to choose the color space of 
the source signal for HDMI, RGB, and component connections.
• The default setting, Auto, functions as follows:
•  HDMI: If the Auxiliary Video Information (AVI) infoframe contains color space and/   
  or range data, the H8030 uses that information. Otherwise, for RGB sourc\
es, the    
  H8030 uses the RGB-Video color space. For component SDTV and EDTV      
  resolutions, REC601 is used. For other component video resolutions, REC709 is    
 used.
•  RGB: If Hsync or Vsync signals are present, the H8030 uses the RGB-PC color    
  space. Otherwise, REC601 is used for SDTV and EDTV sources, and REC709 f\
or all  
  other sources.
•  Component: For SDTV and EDTV resolutions, the H8030 uses the REC601 color    
  space. For all other resolutions REC709 is used.
In most cases, the Auto setting determines the correct color space to use. If it does not, \
you can force the H8030 to use a specific color space. Choose one of the following: • REC709  sets the color space matrix to that defined in ITU-R BT.709.
•  REC601  sets the color space matrix to that defined in ITU-R BT.601.
•  RGB-PC  uses RGB color space and sets black at 0,0,0 RGB and white at      
  255,255,255 RGB.
•  RGB-Video  uses RGB color space and sets black at 16,16,16 RGB and white at    
 235,235,235.
Video Standard:  Select Video Standard from the Advanced menu to specify the color 
system for composite video or S-Video input signals.
Different countries use different formats for video signals. Select the appropriate Video 
Standard for your region:
• Auto: The color systems are automatically identified and the format is set accordingly.
•  NTSC: (National Television Systems Committee): This is the standard format used  
H8030 Home Theater Projector - User Manual  
						

							33
 mainly in the United States and Japan.
•  PAL: (Phase Alternation by Line): This is the standard used in Europe, Australia and  
  many other parts of the world, typically with a 50Hz frame rate.
•  SECAM (Sequential Color With Memory): This is a standard format used mainly in  
  France and Russia.
•  NTSC: This is the standard format used mainly in the United States and Japan.
Gamma:  Select Gamma from the Advanced menu to choose a DLP de-gamma curve. 
Used correctly, the Gamma control can improve contrast while maintaining good details \
for 
blacks and whites.
If excess ambient light washes out the image and it becomes difficult or impossible to see 
details in dark areas, lower the gamma setting to compensate. This improves contrast 
while maintaining good details for blacks. Conversely, if the image is washed out and 
unnatural, with excessive detail in black areas, increase the setting.
• CRT sets the gamma to 2.5. 
•  Film sets the gamma to 2.2. 
•  Video is similar to Film gamma but differs in dark areas of the image to correspond to   
  the function that video cameras use to create images. 
•  Bright sets the gamma to 2.0.
•  Graphics should only be used for computer presentations that require inc\
reased    
  brightness at the cost of grayscale accuracy. 
Color temperature:  Color temperature defines the “color of gray;” that is, adjusts the 75% 
white point to various color points.
To choose a color temperature setting, select Color Temperature from the Advanced menu. 
Then, press  ◄
 ►
 to select 5500K, 6500K, 7500K, 9300K. The default setting, 6500K, is 
appropriate for most situations. Higher settings produce a “bluer pic\
ture; lower ones impart 
a reddish hue to the image. 
Gamut:  Select Color Gamut from the Advanced menu to select a color gamut (range) that 
may be different from the default color gamut.
Each setting defines the precise hue of each primary (red, green and blue) and secondary 
(yellow, cyan and magenta) color component used to generate the millions of co\
lors 
produced in displays. Changing either or both of these numbers changes t\
he hue of 
the color and relocates the “triangle” for possible colors. For ex\
ample, changing the x/y 
coordinates for red moves the color closer to either orange or violet, w\
hich in turn affects 
all displayed colors having a red component.
• Auto automatically chooses the appropriate color gamut:
 
◦ SMPTE C for NTSC, 480i and 480p sources.
 
◦ EBU for PAL, SECAM, 576i and 576p sources.
 
◦ REC709 for all other sources.
•  REC709 chooses the REC709 color gamut.
•  SMPTE-C to choose the SMPTE-C color gamut.
•  EBU to choose the EBU color gamut.
H8030 Home Theater Projector - User Manual  
						

							34
• NATIVE It displays the fully saturated LED color gamut and also enable HSG\
 feature  
  for custom color gamut settings.
Brilliant Color:  Enable (On) or disable (Off), which improves brightness in grays and 
secondary colors by allowing simultaneous display of multiple colors fro\
m the LED light 
sources.
Adaptive Contrast:  Adaptive Contrast enhancement expands the light and dark portions 
of an output image according to the mean luminance of the input image. 
RGB Adjust:  Also known as White Balance Adjust. This feature is to remove any trace 
of color from the white areas of the projected image and to achieve to t\
he desired white 
temperature, choose RGB Adjust from the Advanced menu and press ENTER. This 
displays the RGB Adjust sub-menu.
• Gain Use the Gain controls to correct color imbalances in the bright are\
as of the    
  image. A good way to do this is to use a test pattern consisting mostly of solid\
 white  
  areas, such as an 80 IRE “window” pattern. If the white areas cont\
ain traces of red,  
  green or blue, decrease the Gain for that color.
•  Offset Use the Offset controls in the RGB Adjust sub-menu to correct color      
  imbalances in the dark areas of the image. A good way to do this is to use a test    
  pattern consisting mostly of dark gray areas, such as a 30 IRE “windo\
w” pattern. If  
  the gray areas contain traces of red, green or blue, decrease the Offset for that color.
Note:  The Gain controls increase or decrease the full-scale input range; the O\
ffset 
controls shift the entire range, resulting in a change in brightness. Generally, higher 
Gain settings reduce the image contrast; higher Offset settings reduce the image 
brightness. 
Fine Sync:  To fine-tune the position and other image attributes.
•  V Position: Select this function to adjust the vertical position of the image within the  
  designated image area, up to 25% up or down of the image height.
•  H Position: Select this function to adjust the horizontal position of the image within   
  the designated image area, up to 25% right or left of the image width.
•  Phase (for RGB or Component sources): This control adjusts the phase of the pixel  
  sampling clock relative to the incoming signal. Adjust the phase when an RGB or    
  Component image still shows shimmer or “noise” after Tracking has been optimized.
•  Note: Adjust the Phase after adjusting Tracking (see below). If some shimmer from  
  a video or HDTV source persists, use the Noise Reduction controls to rem\
ove high- 
  frequency noise from the signal.
•  Tracking (for RGB or Component sources): Tracking determines the frequency of the   
  pixel sampling clock, indicated by the number of incoming pixels per line, so that all 
pixels generated by a particular source are sampled. Steady flickering or several soft 
vertical stripes or bands across the entire image indicates poor pixel t\
racking. Proper 
pixel tracking helps ensure that the image quality is consistent across \
the screen, that 
aspect ratio is maintained and that pixel phase can be optimized.
H8030 Home Theater Projector - User Manual  
						

							35
• Sync Level (for Component sources only): Select Sync Level to adjust the
 voltage 
  
  level of the H8030 Sync signal detection circuitry. Sync Level adjustment is
     
  occasionally necessary when a DVD player or HDTV source signal drops “below    
  black” (for example, during scenes with explosions or when subtitles are present)    
  and causes the projector to tem¬porarily lose sync. If the Sync Level\
 from the source  
  is persistently too low, the projector won’t sync with the source at all. The
 range is   
  from 50 to 256 millivolts (mV) inclusive. The default setting is 240 mV and should    
  rarely require adjustment. 
OSD Introduction – SYSTEM
MAINSER VICELANGUAGECONTROLSYSTEMADVANCED
Menu = Exit Menu Select   Scroll  
Source Enable
Menu Position
Blank Screen
Auto Power Of
f
Auto Power On
Rear Projection
Celling Mode
Logo Display
Lamp Power On 
 Off
On   Off
On   Off
On   Off
On   Off
Economy   StandardEnter
Source Enable: 
To enable or disable selection of a source, choose Source Enable from 
the System menu and press ENTER. This displays the Source Enable sub-menu
Menu Position: Select Menu Position from the System menu to change the OSD menu 
position. 
Blank Screen:  Select Blank Screen from the System menu to choose the color of the 
blank screen that appears when no source signal is present. The options are Logo, Black, 
Blue and White. The default is Black.
Auto Power Off:  Set Auto Power Off to On to have the H8030 turn itself off after 20 
minutes of inactivity (no source signal present).
Auto Power On:  The default setting is Off. If you set it to ON, the projector will 
automatically start up when it is connected to AC power. If you plug the projector’s power 
cord into an AC socket with a switch, you can use this function to start up the proje\
ctor 
using the socket’s switch instead of the remote. If you do not need this function, please\
 set 
it to Off. 
Rear Projection:  This control reverses all images and menus, and is necessary when the 
projector is used in rear-projection applications. The default is Off.  Refer to Page 15 --- 
Modes of installation
Celling Mode : This control flips the image so the projector can be used in ceiling mounted 
installations. The default setting, Auto, automatically determines the orientation using an 
internal sensor.  Refer to Page 15 --- Modes of installation
H8030 Home Theater Projector - User Manual  
						

							36
Logo Display: This feature enable and disable Vivitek brand logo during projector warming 
up stage .
Lamp Power:  This control  ECO will automatically set the lamp power to 80%. Standard\
 
will set the power to 100%.  Standard Projection is carried out using th\
e normal lamp 
power to obtain the brightest projection display.  ECO Projection is carried out in the 
energy saving mode to ensure the longest service life of the lamp.
OSD Introduction - CONTROL
Select Control from the Main Menu to set various options related to cont\
rol of the projector.
MAINSERV ICELANGUAGECONTROLSYSTEMADVANCED
Menu = ExitM enu Select   Scroll  
1 Key
2 Key
3 Key
4 Key
5 Key
Trigger-1
Auto Source   
Enter
   Enter
   Enter
   Enter
   Enter
Screen  16:9 Letterbox  4:3 4:3 Narrow  RS232
On      Off
1 Key / 2 Key / 3 Key / 4 Key / 5 Key:  These menu items assign the function of the keys 
numbered 1 through 5 on the remote .
There are seven sources corresponding to the eight connections to the pr\
ojector. When 
you assign a source to a numbered key, the projector immediately goes to that source 
when the key assigned to it is pressed.
If the chosen source is disabled via the Source Enable menu, this settin\
g has no effect.
Trigger 1:  Select Trigger 1 from the Control menu to specify when the Trigger 1 port 
outputs 12 volts. There is a three-second delay before activation to prevent operation whi\
le 
selecting an aspect ratio.
•  Screen: The port to output 12 volts whenever the lamp is on.
•  16:9: Causes the port to output 12 volts whenever the 16:9 aspect ratio is chosen.
•  Letterbox: Causes the port to output 12 volts whenever the Letterbox aspect ratio is   
  chosen.
•  4:3: Causes the port to output 12 volts whenever the 4:3 aspect ratio is chosen.
•  4:3 Narrow: Causes the port to output 12 volts whenever the 4:3 Narrow aspect ratio is   
  chosen.
•  RS232: Causes the port to output 12 volts when an RS232 screen trigger 1 “on” 
command is received and stop when trigger 1 “off” command is received. The 12 volt 
output also stops when the projector is turned off.
Auto Source:  Default setting is “Off”. By enabling this function, the projector will 
automatically determine the source of input every time it is turned on s\
o that the user will 
not have to make the selection on the OSD Menu. Setting the function off will require the 
H8030 Home Theater Projector - User Manual  
						

							37
user to specify source of image input on the OSD Menu in order for the p\
rojector to display 
the intended image.
OSD Introduction – LANGUAGE
Choose the OSD display language that you familiar. English, French or Spanish.
MAINSERVICELANGUAGECONTROLSYSTEMADVANCED
Menu = ExitM enu Select   Scroll  
English
Français
Español
OSD Introduction – SERVICE
 The functions covered in this unit relate to the display of some basic i\
nformation about the 
projector.
MAINSERVICELANGUAGECONTROLSYSTEMADVANCED
Menu = ExitM enu Select   Scroll  
Model Name
Serial Number
Software Version
Active Source
Pixel Clock
Signal Format
H/V Refresh Rate
Lamp Hours
Factory Reset
Blue Only
Te st Patterns
Altitude H8030
-------------------------
S-V
ideo
-------------------------
H:  KHz V:  Hz
-------------------------
Enter
On   Off
Low   High
• Model:  The designated model number of the projector. 
•  Serial Number:  The designated serial number of the projector. 
•  Software Version:  The version of software installed on the projector. 
•  Active Source:  Displays the current detected sources. 
•  Pixel Clock:  Displays the pixel clock of the current input signal. 
•  Signal Format:  Displays the format of the current input signal. 
•  H/V Refresh Rate:  Displays the horizontal and vertical refresh rates for the current  
H8030 Home Theater Projector - User Manual  
						

							38
   image. 
• Lamp Hours:  Display the Lamp usage time. 
•  Factory Reset:  Use this function to restore the configurations in the OSD Menu back   
    to factory default. Note that this function will not apply to items including no signal,   
  network, Projector control, startup Logo, language, High Altitute mode.
•  Blue Only:  Enabling this option will make the projector display only blue color to\
    
  facilitate the process of image inspec¬tion for the service personnel\
. For detailed    
  instructions on how to use this function, consult a qualified service personnel.
•  Test Patterns:  The H8030 has numerous internal test patterns that are useful to    
  technicians for advanced calibration, measurement and fault isolation purposes. To  
    access them, select Test Patterns from the Service menu and set it to On. 
Press  ◄ ► on the remote control unit or built-in keypad to cycle through the test\
The available test patterns are:
•  White
•  Black
•  Red
•  Green
•  Blue
•  Cyan
•  Magenta
•  Yellow
•  ANSI Checkerboard
•  Horizontal Gray Ramp
•  Focus Grid
•  Off
•  Altitude: Use this function to control the projector’s cooling fan. You can set it to Low  
  or High. The default setting is Off. 
In most cases, the default setting (Low) will maintain the correct ope\
rating 
temperature. If in certain high-altitude operating environments, you may\
 need to 
change this setting to High.
H8030 Home Theater Projector - User Manual  
						

							39
Change Lamp
The lifecycle of ordinary projection lamp typically lasts for 2000 hours\
 (Normal mode), 
4000 hours (Economy mode) before requiring replacement (different lamp configurations 
will affect lamp life). From the OSD Menu to check how long a lamp has been us\
ed. You 
should also replace the lamp when the projected image gets noticeably da\
rker. Contact 
your local dealer to purchase new certified lamps for your projector.
To replace the projector lamp
1. Turn off the projector and unplug the power cord. Let the projector cool for      
  approximately 60 minutes before removing the lamp module for replacement.
When you turn off the projector, the lamp inside the projector will still be very hot 
(approximately 200 ~ 300°C). If you at- tempt to replace the lamp without allowing the 
projector to cool, you could risk scalding yourself. This is why you should wait for no 
less than 60 minutes for the lamp to cool down in order to perform the r\
eplacement 
safely.
2.  Loosen the lamp cover. 3. Use a screw driver to loosen the screws  
  as shown in the illustration.
4. Grasp the metal rod on the lamp cover  
  and pull the lamp out. 5. 
Insert the new lamp in the direction    
  shown in the illustration into the lamp  
  assembly; tighten the two screws using  
  a screw driver and make sure the lamp  
  is firmly secured to prevent the lamp  
  from shaking or poor contact.
6. Replace the lamp cover and firmly    
  secure the two screws on the lamp    
  cover.
H8030 Home Theater Projector - User Manual  
						

							40
Maintenance and Troubleshooting
Table below provides some general guidelines for troubleshooting problems\
 you may 
encounter with the H8030. If the suggested solutions fail to resolve the\
 problem or if you 
encounter an issue not described here, please contact Vivitek Technical.
Troubleshooting Chart
LED lights solid red.  
  
  Fans are  not working prop erly or 
power-on self-tes t \fas failed (Note\b.  
  Power o  t\fe H8030 and allow\f it  
to cool down. Turn \ft\fe projector 
back on. If t\fe prob\f lem persis ts, 
plea se contact Vivitek Tec\f\fnical 
Su pp ort for assistance . 
  Note: You can  obtain more detailed informao\fn about t\fe  same cause of t\fe error condion using  TRS-232 commands  
Symptom!Possible Cause (s )!Solution!
T\fe projector does  not turn on. !
!•  T\fe H803 0 is not plugged in \for t\fe 
AC outlet is not a\fcve.  
!
  Ensure t\fat t\fe H8030\f  is 
plugged in and t\fat\f t\fe AC  
outlet is acve. !
The remote control does \anot 
work correctly .
!
• The ba\feries  have run out.  
•  \bR code set mismatch be tween 
remote  control unit and pr\aoj ector.  
!
  Replace the ba\feries\a  
   Press and hold the \aL\bGHT an d 
ENTER remote contr\aol bu\fons  
simultaneo usly unl the 
remote  control back -lighng 
“blinks” (approxima\ately ve 
seconds). Then, tr\ay again. !
The projector is  on and OSD 
menus appear, but th\aere is no  
video  image on-screen .
!
  \bncorrect source se\alecon . 
   Source component is\a not turned  
on. 
   Source component is\a connec ted 
incorrectly or not\a at all. !
  Select the correct\a  source. 
   Turn on the source . 
   Check cable connec\aon from  
source co mponent to  
projector. !
A projected imag e from a DV D 
is split or ot\ferwi\lse scra mbled.
!
\b  DVD player is conne\lcted to t\fe 
Component input an\ld set to  
progressive scan m\lode .! \b
  Turn o  progressive scan  on 
t\fe DVD player .!
Image  is blurred.!\b  T\fe le ns is not correctly f\locused. !\b  Adjust t\fe focus  wit\f t\fe 
remote  control.!
Image is too brig\ft and/or \llacks 
denion  in t\fe brig\ft areas\l of  
t\fe image.
!
\b   Contrast is  set too \fig\f.! \b  Lower t\fe contrast \l seng.!
Image appear s “was\fed out”  
and /or dark areas\l appear too 
brig\ft .! \b
  Brig\ftness is  set too \fig\f.! \b  Lower t\fe brig\ftness\l  seng.!
Colors in t\fe im age are 
swap ped; for example, r\leds  
appear blue or vice\l  versa. ! \b
  T\fe Red/ Pr, Green/Y or Blue/P\l b 
\b   outputs from t\fe so\lurce are 
connected 
\b   to t\fe wrong inputs\l on t\f e 
\b   H8030. ! \b
  Ensure t\fat t\fe sou\lrce outputs 
are connected to t\l\fe correct 
H8030 input. !
RGB-HD images appear “noisy”  
 \b
 
Tracki ng and P\fas e sengs need  
adjustment .
  \b
 
Manually ad just Tracking and 
P\fase sengs .
 
LED is flashing red.   
  \b
  H8030 intern al temperature is to\l o \fig\f 
(Note).  \b
  Power o t\fe  H8030 and allow it  
to cool down. Ensur\le t\fat  t\fe 
intake and ex\faust \lvent s are not 
blocked.  Turn  t\fe projector back  
on. If t\fe problem pe\lrsists, please  
contact Vivitek Te\lc\fnical Support  
for assistance .  
H8030 Home Theater Projector - User Manual