Vivitek Projector H8030 User Manual

41
Serial Communications
RS-232Connection and Port Configuration
To interface the H8030 with a home theater automation/control system or a\
 PC running 
terminal emulation software:
1. Connect it to your control system or PC. 
2.  Start a terminal session on your PC using a terminal-emulation program, \
such as    
  HyperTerminal. 
3.  Configure the RS-232 controller or PC serial port as follows: 38400 bps, no parity , 8   
  data bits, 1 stop bit and no flow control. 
4.  Type ky or op followed by a...

42
Serial Command Key Names
RS232 KeynameRemote ButtonDescription
power.on
lTurn power on.
power.off
Turn power off.
menu
MENUBring up or cancel menu display.
enter
ENTERKeypad enter.
down
Keypad down arrow.
up
Keypad up arrow.
left

Keypad left arrow.
righ

Keypad right arrow.
bright
Bring up or cancel brightness slider
contrast
Bring up or cancel contrast slider
sharp
SHARPBring up or cancel sharpness slider
nr
NRBring up or cancel noise reduction slider
gam.sw
GAMMASwitch to the next gamma
src.1...

43
Operations Commands: Operations commands allow more flexible and direct control 
of the projector. The syntafor operations commands is as follows:
op  [CR]
(Precede    and   with a space.)
The command type can be one of 5 functions:
Operation Control Commands
Function Command Action on unit
Set = Makes the unit take that value.
Get ?asks what the current value is.
Increment +Add 1 to the current value.
Decrement -Subtracts 1 from the current value.
Execute Performs and action as a reset.
•  Below are...

44
Serial Operation Commands (continued)
The last two commands show what happens when a control is grayed out. In\
 this case, the 
sharpness mode was set to advanced (value = 1) and then the simple sha\
rpness slider 
was attempted to be adjusted and queried. The response was “NA” or not available.
Serial Command OperandValue  Notes
aspect = ?0 = 16:9 
1 = Letterbox 
2 = 4:3 
3 = Theaterscope  
4 = Native 
recall.mem = ?0 = Preset A 
1 = Preset B 
2 = Preset C 
3 = Preset D 
4 = Default 
save.mem =0 =...

45
video.stand= ?0  = Auto 
1 = NTSC 
2 = PAL 
3 = SECAM 
gamma = ?0 = CRT 
1 = Film  
2 = Video  
3 = Bright 
4 = Graphics 
color.temp = ?0 = 5500K 
1 = 6500K 
2 = 7500K 
3 = 9300K 
4 = Native 
color.gamut = ?0  = Auto 
1 = REC709 
2 = SMPTE C 
3 = EBU 
4 = Native 
bcolor = ?0 = Off 
1 = Smooth 
dlp.frame = ?0  = Auto 
2 = 48 Hz 
3 = 50 Hz 
4 = 60 Hz 
red.offset = ? + -0-200
green.offset = ? + -0-200
blue.offset = ? + -0-200
red.gain = ? + -0-200
green.gain = ? + -0-200
blue.gain = ? + -0-200
v.pos = ?...

46
blank.screen= ?0 = Black 
1 = Blue 
2 = White 
3 = Logo 
auto.poweroff = ?0 = Off 
1 = On 
auto.poweron = ?0 = Off 
1 = On 
rear.proj = ?0 = Off 
1 = On 
ceil.mode = ?0 = Off 
1 = On 
2  = Auto 
startup.logo = ?0 = Off 
1 = On 
1.key 
2.key 
3.key 
4.key 
5.key  = ?
0 = HDMI 1 
1 = HDMI 2 
2 = RGB 
3 = YPrPb 1 
4 = S-video 
5 = Video 
auto.source = ?0 = Off 
1 = On 
M1. key = ?0 = Preset A Label ‘A’ on the RC 
key
M2. key = ?0 = Preset B Label ‘B’ on the RC 
key
M3. key = ?0 = Preset C Label ‘C’ on...

47
v.refresh  ? Hz
pixel.clock   ? MHz
signal   ?
total.hours   ?
environment   ? Temperatures
fact.reset (execute)
lamp reset (execute)
pattern =0 = White 
1 = Black 
2 = Red 
3 = Green 
4 = Blue 
5 = Cyan 
6 = Magenta 
7 = Yellow 
8 = ANSI Checkerboard  
9 = Horizontal Gray Ramp  
10 = Focus Grid 
11 = Off 
altitude = ?0 = low 
1 = high 
status ?0 = standby 
1 = warm up 
2 = imaging 
3 = cooling  
4 = error 
FVER   ?
trig.1 
trig.2 = ?
0 = Screen 
1 = 16:9 
2 = Letterbox 
3 = 4:3 
4 = 4:3 Narrow 
5 =...

48
RS-232 Error Codes
If an errcode ? command returns one of the following values, you have en\
countered a 
likely system error requiring the attention of a qualified service technician. Try resetting the 
projector by powering it off, allowing it to cool and powering it on again.
The specific code number identifies the source of the error detected, and is particularly 
useful in cases where the projector is far away. For example, the code “7” means that Fan 
1 has failed.
Error Code Description
0 Inlet...

49
Specifications
H8030 Specifications
Optics
TechnologyTI DLP 1080p (1920 x 1080) 0.95” DMD
Light Source UHP Lamp  230W
Projector Lens Standard Lens throw ratio: 1.85 to 2.4:1
Short Lens throw ratio: 1.56 to 1.86:1 (optional)
Long Lens throw ratio: 2.4 to 4.0:1 (optional)
Lens Shift • Vertical ± 60%
•  Horizontal ± 15%
Image width range 8ft to 30ft
Electrical
I/O - Video Input • DB15 pin RGB
•  2 x HDMI
•  Component 1 - RCA
•  Composite (RCA)
•  S-Video
I/O - Power Input IEC-320-C14receptacle
Projector...

50
H8030 Specifications (continued)
Reliability
Operating Temperature• 7500 ft.~10000 ft. (2286m ~ 3048m): 50 ~ 95°F (10 ~  
  35°C), Humidity: 0% ~ 85%
•  Under 7,500 ft. (2286m): 50 ~ 104°F (10 ~ 40°C),   
  Humidity: 0% ~ 85%
Storage -4 ~ 140°F (-20 ~ 60°C), Humidity: 5% ~ 90%
Standard Accessories
Power CordUS 110VAC
Remote and Batteries For set up and use only
HDMI Cable For set up and use only
User Manual CD For set up and use only
Warranty Card
Allen Wrench For lens shift adjustment
Note:...