Vivitek Projector H5095 Series User Manual

— 52 — 
Source Filter 
Press the ENTER button to enter the Source Filter sub menu. 
 
ITEM DESCRIPTION 
DVI Press the ◄► buttons to enter and enable or disable the DVI sourceK 
HDMI Press the ◄► buttons to enter and enable or disable the HDMI source. 
DisplayPort Press the ◄► buttons to enter and enable or disable the DisplayPort source. 
VGA1 Press the ◄► buttons to enter and enable or disable the VGA1 source. 
VGA2 Press the ◄► buttons to enter and enable or disable the VGA2 source. 
Component Video...

– 53 – 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be replaced with a certified 
replacement part, which you can order from your local dealer.  
 Important: 
a. The projection lamp used in this product contains a small amount of mercury. 
b. Do not dispose this product with general household waste. 
c. Disposal of this product must be carried out in accordance with the regulations of your local  
authority. 
 Warning:...

— 54 — 
4.  Unlock the lamp cover. 
 
5.  Pull up and remove the 
cover. 
6.  Use a screwdriver to 
remove the screws from 
the lamp module. 
 
7.  Pull out the lamp module. 
   
       

– 55 – 
8.  Reverse steps 1 to 7 to 
install the new lamp 
module.  
While installing, align the 
lamp module with the 
connector and ensure it is 
level to avoid damage. 
Note:  
The lamp module must sit 
securely in place and the 
lamp connector must be 
connected properly before 
tightening the screws.  
 
    

— 56 — 
Resetting the Lamp 
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 
1.  Press the MENU button to open 
the OSD menu. 
 
2.  Press the cursor ◄► button to 
move to the Settings 2 menu. 
Press the cursor button to move 
down to Advanced 1 and press 
enter. 
3.  Press the cursor ▼▲ button to 
move down to Lamp Hour Reset. 
 
4.  Press the cursor ► or Enter 
button.  
A message screen appears. 
 
5.  Press ▼▲◄► buttons to reset 
the lamp hour. 
6....

– 57 – 
Cleaning the filter (filter: optional parts) 
The air filter prevents dust from accumulating on the surface of the optical elements inside the 
projector. If the filter is dirty or clogged, your projector may overheat or degrading the projected image 
quality. 
1.  Turn off the projector, and 
unplug the AC power cord 
from the AC outlet. 
 
2.  Cleaning the filter with a 
vacuum cleaner. 
 
 Caution: 
Recommend avoiding dusty or smoky environments when you operate the projector, it may cause...

— 58 — 
Replacing the Filter 
1.  Turn off the projector, and 
unplug the AC power cord 
from the AC outlet.  
Clean up the dust on the 
projector and around the 
air vents.  
Pull out the filter cover and 
remove from the projector 
 
2.  Lift the filter from the filter 
cover. 
 
 
3.  Replace a new filter 
module or replace filter into 
cover. 
 
4.  Replace the filter cover 
back to the projector by 
pushing gently in the  
direction shown. 
 
 Warning: 
Do not wash the filter with the water or other...

– 59 – 
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
 Warning: 
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so 
could result in a severe burn. 
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings 
on the projector.  
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated 
room for...

— 60 — 
Using the Physical Lock 
Using the Kensington Lock 
If you are concerned about security, attach the projector to a permanent object with the Kensington 
slot and a security cable.  
 
Note: 
Contact your vendor for details on purchasing a suitable Kensington security cable.  
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any 
comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-
4242, http://www.Kensington.com. 
Using...

– 61 – 
TROUBLESHOOTING 
Common problems and solutions 
These guidelines provide tips to deal with problems you may encounter while using the projector. If 
the problem remains unsolved, contact your dealer for assistance. 
Often after time spent troubleshooting, the problem is traced to something as simple as a loose 
connection. Check the following before proceeding to the problem-specific solutions. 
 Use some other electrical device to confirm that the electrical outlet is working. 
 Ensure the...