Vivitek Projector H1188 Series User Manual

							— 12 — 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
 The projector table or stand should be level and sturdy. 
 Position the projector so that it is perpendicular to the screen. 
 Ensure the cables are in a safe location. You could trip over them.  
 
To adjust the angle of the picture, turn the tilt-adjuster right or left until the desired 
angle has been achieved. 
 
 
 
   
						

							– 13 – 
Adjusting the vertical image position 
 The Lens Shift function 
can be used to adjust 
the  position of the 
vertically. 
 
 The display position can 
be shifted upward up to 
9% and down to 5% 
elevation of the display. 
 
 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom  
control (on the projector 
only) to resize the 
projected image and 
screen size . 
 
2.  Use the Image-focus  
control (on the projector 
only) to sharpen the 
projected image . 
3.  Use the KEYSTONE 
buttons (on the 
projector or the remote 
control) to correct 
image-trapezoid (wider 
top or bottom) effect. 
 
4.  The keystone control 
appears on the display.   Lens shift adjustable range     
9%
Shift to top  
9%V
1V
5%V5%
Shift range
Lens shift center position
Shift range      
						

							— 14 — 
Adjusting the Volume 
1.  Press the Volume +/- 
buttons on the remote 
control.  
The volume control 
appears on the display. 
 
2.  Press the MUTE button 
to turn off the volume. 
(This feature is available 
only on the remote).     
						

							– 15 – 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons to navigate and make changes to the OSD.  
 
1. To enter the OSD, press the 
MENU button.  
2. There are six menus. Press 
the cursor ◄► button to 
move through the menus.  
3. Press the cursor ▲▼ button 
to move up and down in a 
menu.  
4. Press ◄► to change values 
for settings. 
5. Press MENU to close the 
OSD or leave a submenu. 
 
Note: 
Depending on the video source, not all items in the OSD are available. For example, the 
Horizontal/Vertical Position items in the Computer menu can only be modified when connected 
to a PC. Items that are not available cannot be accessed and are grayed out.  
 1
2
3
4
5
6
2
2
241165
32  
						

							— 16 — 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic. 
 
2. Press the cursor ▲▼ button until Language is highlighted.  
3. Press the cursor ◄► button until the language you want is selected.  
4. Press the MENU button to close the OSD.   
  
						

							– 17 – 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
Main Menu  Sub Menu   Settings 
Picture >>Basic  Display Mode    Presentation, Movie, Vivid , Bright, 
Game, User1 
   Brightness    0 ~ 100 
   Contrast    -50 ~ 50 
   Color    -50 ~ 50 
   Tint    -50 ~ 50 
   Sharpness    0 ~ 21 
   Reset Pictures 
Setting 
   Reset current display mode value 
Picture >>Advanced  Color temperature    D65, D75, D83 
   Gamma    1.8 / 2.0 / 2.2 / 2.4 / B&W / Linear  
   HSG adjustment  Primary Color R / G / B / C / M / Y 
      Hue -50 ~ 50 
      Saturation 0 ~ 199 
      Gain 0 ~ 199 
   VividSettings  VividMotion Off/ Low / Medium / High 
      VividPeaking 0 ~ 3 
      Flash tone 0 ~ 5 
Display  Aspect Ratio    Auto / 16:9 / 4:3 / Letter Box / Real 
   Keystone    -40 ~ 40 
   Over scan    0 ~ 10 
   PC detail 
adjustment 
 Auto enter 
      Frequency By timing  
      Phase 0 ~ 100 
      Horizontal Position -15 ~ 15 
      Vertical Position -50 ~ 50 
   White Balance  Red Gain -50 ~ 50 
      Green Gain -50 ~ 50 
      Blue Gain -50 ~ 50 
      Red Bias -50 ~ 50 
      Green Bias -50 ~ 50 
      Blue Bias -50 ~ 50 
   User color temp  White Gain Red 5 ~ 195 
      White Gain Green 5 ~ 195 
      White Gain Blue 5 ~ 195 
   3D Setting  3D Mode Auto / Side by Side / Top/Bottom / 
Frame Sequential / 2D to 3D 
      3D Sync DLP-Link / IR-Link / Off 
      3D Sync Invert Off / On  
						

							— 18 — 
Main Menu  Sub Menu   Settings 
Setup >> Basic 
 
Language 
 
  
English, Français, Deutsch, Españ ol, 
Portuguê s, 簡体中文, 繁體中文, Italiano, 
Norsk, Svenska, Nederlands, Русский, 
Polski, Suomi, Dansk, 한국어, 日本語 
   Projection    Front Table / Front Ceiling / Rear Table 
/ Rear Ceiling 
   Auto power off    Disable / 5 / 10 / 15 / 20 / 25 / 30min 
   Sleep timer    Disable / 30min / 1hr / 2hr /3hr / 4hr / 
8hr / 12hr 
   Background color    Black / Blue / Purple 
   Menu Setting  Menu Position Center / Right up / Right down / Left up 
/ Left down 
      Menu display time 5 / 10 / 15 / 20 / 25 / 30 sec 
   Source  PC Disable, Enable 
      HDMI1 Disable, Enable 
      HDMI2 Disable, Enable 
      Component Disable, Enable 
      Video Disable, Enable 
      Quick Auto Search On / Off 
Setup >> Advanced  Audio  Volume 0~10 
      Mute Off, On 
   Lamp  Lamp Mode Normal / ECO / Dynamic Eco 
      Reset Lamp Timer  
    Lamp Hour  
   High Altitude Mode    Off / On 
   Test Pattern    Off /on 
   Close Caption    Off / On 
   12V OUT A    On / Off 
   Reset All   Yes / No 
Status  Source    
  Resolution    
  Lamp Hours  
(ECO, Normal) 
   
  Firmware Version    
  
						

							– 19 – 
PICTURE>>Basic Menu 
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the 
PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the 
PICTURE>>Basic menu. Press ◄► to change values for settings. 
 
ITEM DESCRIPTION 
Display Mode Press the cursor ◄► buttons to set the Display Mode. 
Brightness Press the cursor ◄► buttons to adjust the display brightness. 
Contrast Press the cursor ◄► buttons to adjust the display contrast. 
Color 
Press the cursor ◄► buttons to adjust the video saturation. 
Notes: This function is only available when Component, Video input source is 
selected. 
Tint 
Press the cursor ◄► buttons to adjust the video tint/hue. 
Notes: This function is only available when Component, Video with NTSC system 
input source is selected. 
Sharpness 
Press the cursor ◄► buttons to adjust the display sharpness. 
Notes: This function is only available when Component, Video input source is 
selected. 
Reset Picture 
Settings Press the ENTER button to reset all settings to default values.  
						

							— 20 — 
PICTURE>>Advanced Menu 
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the  
PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the  
PICTURE>>Advanced menu. Press ◄► to change values for settings. 
 
ITEM DESCRIPTION 
Color Temperature Press the cursor ◄► button to set the Color Temperature. 
Gamma Press the cursor ◄► button to adjust the gamma correction of the display. 
HSG Adjustment Press the ENTER button to enter the HSG Adjustment sub menu.  
See HSG Adjustment on page 21. 
VividSettings Press the ENTER button to enter the VividSettings sub menu. See VividSettings on 
page 22.  
						

							– 21 – 
HSG Adjustment 
Press the ENTER button to enter the HSG Adjustment sub menu.  
 
ITEM DESCRIPTION 
Primary Color Press the ◄► buttons to set the Primary Color. 
Notes: There are six sets (R/ G/ B/ C/ M/ Y) of colors to be customized. 
Hue Press the ◄► buttons to adjust the Hue. 
Saturation Press the ◄► buttons to adjust the Saturation. 
Gain Press the ◄► buttons to adjust the dain.