Vivitek Projector DX3320 User Manual

							— 22 — 
Adjusting the Volume 
7.  Press the Volume buttons on the remote 
control. 
The volume control appears on the 
display. 
 
8.  Press the ◄ / ► buttons on the keypad 
to adjust Volume +/-. 
 
 
9.  Press the MUTE button to turn off the 
volume (This feature is available only on 
the remote). 
 
    
						

							– 23 – 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and 
make changes to the OSD. The following illustration shows the corresponding buttons on the projector. 
 
1. To enter the OSD, press the MENU button. 
2. There are three menus. Press the cursor ◄ / 
► buttons to move through the menus.  
3. Press the cursor  / ▼ buttons to move up 
and down in a menu.  
4. Press the cursor ◄ / ► buttons to change 
values for settings. 
5. Press the MENU button to close the OSD or 
leave a submenu. Press the EXIT button to 
return to the previous menu. 
 
Note: 
Depending on the video source, not all items in the OSD are available. For example, the 
Horizontal/Vertical Position items in the Computer menu can only be modified when connected 
to a PC. Items that are not available cannot be accessed and are grayed out.    
						

							— 24 — 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1. Press the MENU button. Press the cursor ◄► button to navigate to Settings 1. Press the 
cursor ▲▼ button to move to the Advanced 1 menu. 
 
2. Press  (Enter) / ► to enter the Advanced 1 sub menu. Press the cursor ▲▼ button 
until Language is highlighted.  
 
3. Press the cursor button until the language you want is highlighted.  
4. Press the MENU button four times to close the OSD.     
						

							– 25 – 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
Main 
Menu 
 
Sub Menu   
 
Settings 
Image  Display Mode    Presentation, Bright, Game, 
Movie, Vivid, TV, sRGB,  
DICOM SIM, User 
  Brightness    0~100 
  Contrast    0~100 
  Computer  Horizontal Position  -5~5 (depend on Autolock) 
    Vertical Position  -5~5 (depend on Autolock) 
    Frequency  0~31 
    Tracking  -5~5 
    Auto Sync  On, Off  
  Auto Image     
  Advanced  Brilliant Color  0~10 
    Sharpness  0~31 
    Gamma  1.8, 2.0, 2.2, 2.4, B&W, Linear 
    Color Temperature  Warm, Normal, Cold 
    Video AGC  Off, On 
    Video Saturation  0~100 
    Video Tint  0~100 
    White Balance R Gain 0~200 
     G Gain 0~200 
     B Gain 0~200 
     R Offset -100~100 
     G Offset -100~100 
     B Offset -100~100 
  Color Manager  Red Hue, Saturation, Gain 0~100 
    Green Hue, Saturation, Gain 0~100 
    Blue Hue, Saturation, Gain 0~100 
    Cyan Hue, Saturation, Gain 0~100 
    Magenta Hue, Saturation, Gain 0~100 
    Yellow Hue, Saturation, Gain 0~100 
    White Red, Green, Blue 0~100 
  
						

							— 
26  —   Main 
Menu   Sub Menu   Settings  
S ettings 1     Source   Source   reference Input Source Select (IR/Keypad)  
Projection   Normal, Rear, 
Ceiling, Rear+Ceiling  Aspect Ratio   Fill, 4:3, 16:9, Letter Box, Native, 2.35:1  
Keystone   H:  - 25 ~ +25  V:  - 30 ~ +30  
Digital Zoom   - 10~10  
Audio   Volume   0 ~10  
Mute   Off, On  
Out   Off, Mini, RCA  
Advanced 1   Language   English, Français, Deutsch, Españ ol, 
Portuguê s,  簡体中文 ,  繁體中文 , Italiano, 
Norsk, Svenska, Nederlands, Русский, 
Polski, Suomi, Ελληνικά,  한국어 , Magyar, 
Čeština,  ةيبرعلا , T
						

							– 27 – 
Main 
Menu 
 
Sub Menu   
 
Settings 
Settings 2  Auto Source    Off, On 
  No Signal 
Power Off 
   0~180 
  Auto Power 
On 
   Off, On 
  Lamp Mode    ECO , Normal, Dynamic ECO 
  Reset All     
  Status  Active Source   
    Video Information   
    Lamp Hours(ECO, Normal, 
Dynamic ECO) 
  
    Software Version   
    Remote ID   
    Serial Number   
    Air Filter Hour   
  Advanced 1  Menu Position  Center, Down, Up, Left, Right 
    Translucent Menu  0%, 25%, 50%, 75%, 100% 
    Low Power Mode  Off, On, On By Lan 
    Fan Speed  Normal, High 
    Lamp Hour Reset   
    Projector ID  0-98 
    Remote ID  Default, 1, 2, 3, 4, 5, 6, 7 
    Network Network State Connect, Disconnect 
     DHCP On, Off 
     IP Address  0~255, 0~255, 0~255. 0~255 
     Subnet Mask 0~255, 0~255, 0~255. 0~255 
     Gateway 0~255, 0~255, 0~255. 0~255 
     DNS 0~255, 0~255, 0~255. 0~255 
     Apply Ok / Cancel 
  Advanced 2  Sleep Timer  0~600 
    Source Filter HDMI1/MHL Disable, Enable 
     HDMI2 Disable, Enable 
     DVI Disable, Enable 
     VGA1 Disable, Enable 
     VGA2 Disable, Enable 
     BNC Disable, Enable 
     S-Video Disable, Enable 
     Composite Video Disable, Enable 
     HDBaseT Disable, Enable 
    Air Filter Timer Reset  OK / Cancel  
						

							— 28 — 
Image Menu  
 Attention !   
All of display mode parameters when changed will be saved to user mode.  
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu. 
Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to enter and change 
values for settings. 
 
ITEM DESCRIPTION 
Display Mode Press the cursor ◄► button to enter and set the Display Mode.  
Brightness Press the cursor ◄► button to enter and adjust the display brightnessK 
Contrast Press the cursor ◄► button to enter and adjust the display contrastK 
Computer Press  (Enter) / ► to enter the Computer menu. See Computer Menu on page 29. 
Auto Image Press  (Enter) / ► to automatically adjustment for phase, tracking, size and 
positionK 
Advanced Press  (Enter) / ► to enter the Advanced menu. See Advanced Feature on page 
30. 
Color Manager Press  (Enter) / ► to enter the color manager menu. See page 32 for more 
information on Color Manager       
						

							– 29 – 
Computer Menu 
Press the MENU button to open the OSD menu. Press ◄► to move to the Image menu. Press ▲▼ to 
move to the Computer menu and then press Enter or ►. Press ▲▼ to move up and down in the 
Computer menu. 
 
ITEM DESCRIPTION 
Horizontal Position Press the cursor ◄► button to enter and adjust the display position to left or right.  
Vertical Position Press the cursor ◄► button to enter and adjust the display position to up or down.  
Frequency Press the cursor ◄► button to enter and adjust the A/D sampling clock. 
Tracking Press the cursor ◄► button to enter and adjust the A/D sampling dot. 
Auto Sync Press the cursor ◄► button to enter and adjust the Auto Sync Position to On or Off. 
  
						

							— 30 — 
Advanced Feature 
Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to 
move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and down in the 
Advanced menu. 
 
ITEM DESCRIPTION 
Brilliant Color Press the cursor ◄► button to enter and adjust the Brilliant Color valueK 
Sharpness Press the cursor ◄► button to enter and adjust the display sharpnessK 
Gamm~ Press the cursor ◄► button to enter and adjust the gamma correction of the displayK 
Color Temperature Press the cursor ◄► button to enter and adjust the color temperature. 
Video AGC Press the cursor ◄► button to enter and enable or disable the Automatic Gain Control 
for video sourceK 
Video Saturation Press the cursor ◄► button to enter and adjust the video saturation. 
Video Tint Press the cursor ◄► button to enter and adjust the video tint/hue. 
White Balance Press the ENTER / ► button to enter the White Balance sub menu. See White 
Balance on page 31  
						

							– 31 – 
White Balance 
Press the ENTER button to enter the White Balance sub menu.  
 
ITEM DESCRIPTION 
R Gain Press the ◄► buttons to adjust the Red GainK 
G Gain Press the ◄► buttons to adjust the Green GainK 
B Gain Press the ◄► buttons to adjust the Blue Gain.  
R Offset Press the ◄► buttons to adjust the Red OffsetK 
G Offset Press the ◄► buttons to adjust the Green OffsetK 
B Offset Press the ◄► buttons to adjust the Blue Offset.