Vivitek Projector D967 User Manual

DLP Projector—User’s Manual 
Top view—On-screen Display (OSD) buttons and LEDs 
1
2
3
4 5
7
8
6
9
1
0
11
12
 
ITEM LABEL DESCRIPTION SEE PAGE
1.   (Power button) Turns the projector On or Off. 11 
2.  BLANK 
Displays a blank screen and mutes audio 
3.  ◄ (Left cursor) /  
Volume-  Navigates and changes settings in the OSD 
Quick Menu – For Volume 
4.  Enter 
Enter or confirm highlighted OSD menu item 
5.  MENU  Opens and exits OSD menus 
6.  ▲ (Up cursor) /  
Keystone+  Navigates and changes settings in...

DLP Projector—User’s Manual 
Rear view 
123456791011
13
141516
128
1718 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  AC IN Connect the POWER cable 11 
2.   (USB) Connect the USB cable from a computer  
3.  VGA OUT  Connect the RGB cable to a display 
(Loop Thru only for VGA IN-1) 
4.  LAN 
Connect a LAN cable from Ethernet 
5.  VGA IN 1  Connect the RGB cable from a computer or component device 
6.  VGA IN 2 Connect the RGB cable from a computer or component device 
7.  DP Connect a DISPLAYPORT CABL E from a...

DLP Projector—User’s Manual 
– 5 –  
Note: 
 To use this feature, you must plug in t he connector before turn on/off the projector. 
 Screen controllers are supplied and  supported by screen manufacturers. 
 Do not use this jack for any thing other than intended use. 
 
Note: 
If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the  
S-VIDEO connector. S-VIDEO provides a better quality signal. 
 
Warning: 
As a safety precaution, disconnect all power to  the projector...

DLP Projector—User’s Manual 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  Tilt adjustor  Rotate adjuster lever to adjust angle position.  15 
2.  Ceiling support holes  Contact your dealer for information on mounting the projector on a 
ceiling 
3.  Height adjustor Adjuster drops down when adjuster button is 
pushed. 
4.  Height adjustor button 
Push to release adjustor. 
15 
 
Note: 
When installing, ensure that you us e only UL Listed ceiling mounts. 
For ceiling installations, use approved...

DLP Projector—User’s Manual 
Remote Control Parts  
 
Important: 
1. Avoid using the projector with bright fluore scent lighting turned on. Certain high-frequency 
fluorescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the  remote control and the projector. If the path 
between the remote control and the  projector is obstructed, you can bounce the signal off certain 
reflective surfaces such  as projector screens. 
 
3. The buttons and keys on the...

DLP Projector—User’s Manual 
— 8 — 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  IR transmitter  Transmits signals to projector 
2.  Status LED  Lights when the remote control is used 
3.  Laser Press to operate the on-screen pointer 
4.  Up  Up arrow when connected through USB to a PC  
(Not available in this series) 
5.  Right Right arrow when connected through USB to a PC 
 (Not available in this series) 
6.  Down Down arrow when connected through USB to a PC  
(Not available in this series) 
7.  Page Down...

DLP Projector—User’s Manual 
– 9 –  
Remote Control Operating Range 
The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a little...

DLP Projector—User’s Manual 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment 
cover by sliding the cover in the 
direction of the arrow. 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods. 
 
 
— 10 —  

DLP Projector—User’s Manual 
– 11  – 
SETUP AND OPERATION 
Starting and Shutting  down the Projector 
 
1.  Connect the power cord to the 
projector. Connect the other end to 
a wall outlet. 
The 
 POWER LED on the 
projector light. 
2.  Turn on the connected devices.  
3.  Ensure the POWER LED not a 
flashing. Then press the 
  POWER  
button to turn on the projector.  
 
The projector splash screen displays 
and connected devices are 
detected. 
 
See  Setting an Access Password 
(Security Lo
 ck) on...

DLP Projector—User’s Manual 
5.  When the “Power Off? /Press 
Power again” message appears, 
press the POWER  button. The 
projector turns off. 
 
Caution: 
1. Be sure to remove the lens  cap before starting projector.  
2. Do not unplug the power cord until all of fans  are stop–indicating the projector has cooled down. 
 
 
— 12 —