Vivitek Dw882st User Manual

							— 2 — 
Views of Projector Parts  
Front-right View 
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  IR receiver Receive IR signal from remote control 
2.  Lens Projection Lens 
3.  Focus ring Focuses the projected image 16 
4.  Function keys See Top view—On-screen Display (OSD) 
buttons and LEDsK 3 
 Important: 
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp 
cool. Do not obstruct any of the ventilation openings. 1234 ！  
						

							– 3 – 
Top view—On-screen Display (OSD) buttons and LEDs 
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  ▲ (Up cursor) / 
Keystone  
Navigates and changes settings in the OSa 
Quick Menu – For Keystone 
17 2.  MENU Opens and exits OSD menus 
3.  ◄ (Left cursorF Navigates and changes settings in the OSa 
4.  ▼ (Down cursor) / 
Keystone  
Navigates and changes settings in the OSa 
Quick Menu – For Keystone 
5.  ECO Enter the lamp mode menu 
6.  SOURCE Navigates and changes settings in the OSD 
Enter the Source menu 
17 7.   (Power button) Turns the projector On or Off. 
8.  ► (Right cursor) Navigates and changes settings in the OSa 
9.  AUTO Navigates and changes settings in the OSD 
Optimizes image size, position, and resolution 
10.  Enter Enter or confirm highlighted OSD menu item 
11.  POWER LED 
Solid Green  Standby, Lamp Lit, over temperature 
54 
Flashing Green System Initialized,  System Power 
On , Cooling ,  Error code 
12.  TEMP LED Solid Red Over temperature 
13.  LAMP LED Solid Red Lamp Fail. 
Flashing Red Error code 
 1
2
3
4
5
6
7
8
9
10
131112     
						

							— 4 — 
 Rear view 
 Warning: 
As a safety precaution, disconnect all power to the projector and connecting devices before making 
connections. 
 
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  AC IN Connect the POWER cable 11 
2.  LAN Connect a LAN cable from Ethernet 
3.  AUDIO IN 1 (VGA 1) Connect an AUDIO cable from the audio device 
4.  HDMI Connect the HDMI cable from a HDMI device 
5.  AUDIO IN 2 (VGA 2) Connect an AUDIO cable from the audio device 
6.  VGA OUT Connect the RGB cable from a computer 
7.  AUDIO IN 3  
(S-VIDEO/VIDEO) Connect an AUDIO cable from the audio device 
8.  VGA 1 Connect the RGB cable from a computer or components device 
9.  VGA 2 Connect the RGB cable from a computer or components device 
10.  USB POWER 
(5V/1.5A) Connect the USB cable for power supply. 
11.  S-VIDEO Connect the S-VIDEO cable from a video device 
12.  VIDEO Connect the COMPOSITE cable from a video device  
13.  Kensington Lock Secure to permanent object with a Kensington®  Lock system 52 
14.  MINI USB Connect the USB cable from a computer  (For service only) ！ 123456789101112
131415161718  
						

							– 5 – 
15.  RS-232C Connect RS-232 serial port cable for remote control 
16.  MIC Connect the Microphone for use 
17.  AUDIO OUT Connect an AUDIO cable to audio amplifier 
18.  12V TRIGGER Connect the 12V OUT (Screen Trigger-- For screen controllers used) 
 
  
						

							— 6 — 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  Ceiling support holes Contact your dealer for information on mounting the projector on a 
ceiling 
2.  Tilt adjustor  Rotate adjuster lever to adjust angle position.  15 
 
Note: 
When installing, ensure that you use only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw 
depth of 12 mm (0.47 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount 
load capacity must exceed the weight of the installed equipment, and as an additional precaution 
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a 
period of 60 seconds. 
 30.5
[1.201]
45.5
[1.791]
154.5
[6.083]
152.22
[5.993]
132.72
[5.225]
61.72
[2.43]
2
2
2
1
1
1  
						

							– 7 – 
Remote Control Parts 
 
Important: 
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency 
fluorescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the remote control and the projector. If the path 
between the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the projector have the same functions as the corresponding buttons on 
the remote control. This user’s manual describes the functions based on the remote control. 
 
Note: 
Complies with FDA performance standards for laser products except for deviations pursuant to 
Laser Notice No. 50, dated June 24, 2007  ！  
						

							— 8 — 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR transmitter Transmits signals to projector 
2.  Status LED Lights when the remote control is used 
3.  Laser Press to operate the on-screen pointer 
4.  Up Up arrow when connected through USB to a PC 
5.  Right Right arrow when connected through USB to a PC 
6.  Down Down arrow when connected through USB to a PC 
7.  Page Down Page down when connected through USB to a PC 
8.  Up cursor  Navigates in the OSD 
17 9.  Right cursor  Navigates and changes settings in the OSD 
10.  Down cursor Navigates in the OSD 
11.  Volume +/- Adjusts volume 16 
12.  Mute Mutes the built-in speaker 
13.  Zoom+ Zoom in  
14.  Zoom- Zoom out 
15.  Freeze  Freeze/unfreezes the on-screen picture 
16.  Blank Makes the screen blank 
17.  Source Detects the input device 
18.  Auto Auto adjustment for phase, tracking, size, position 
19.  Menu Opens or exit the OSD  17 
20.  Status Opens  the  OSD  Status  menu  (the  menu  only  opens 
when an input device is detected) 33 
21.  Keystone 
top/bottom Corrects image-trapezoid (wider top/bottom) effect 16 
22.  Left cursor Navigates and changes settings in the OSD  
17 
23.  Enter Changes settings in the OSD 
24.  Page Up Page up when connected through USB to a PC 
25.  Left Left arrow when connected through USB to a PC 
26.  Enter Enter key when connected through USB to a PC 
27.  Power  Turns the projector on or off 11 
28.  Laser Use as on-screen pointer. DO NOT POINT IN EYES. 
Caution: 
Use of controls, adjustments or performance of procedures other than those specified herein may 
result in hazardous laser light exposure. 
 ！  
						

							– 9 – 
Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the projector does not respond to the remote control, 
move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using the remote control or the buttons on the top of the projector. All 
operations can be carried out with the remote control; however, the buttons on the projector are 
limited in use.   
						

							— 10 — 
SETUP AND OPERATION 
Inserting the Remote Control Batteries  
1.  Remove the battery compartment 
cover by sliding the cover in the 
direction of the arrow. 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries according to local ordinance regulations.  
 
3. Remove the batteries when not using the projector for prolonged periods. 
       ！  
						

							– 11 – 
Starting and Shutting down the Projector 
 
1.  Connect the power cord to the 
projector. Connect the other end to 
a wall outlet. 
The  POWER LED on the 
projector light. 
 
2.  Turn on the connected devices. 
3.  Ensure the POWER LED not a 
flashing. Then press the  POWER 
button to turn on the projector.  
 
The projector splash screen displays 
and connected devices are 
detected. 
 
See Setting an Access Password 
(Security Lock) on page 13 if 
security lock is enabled. 
 
4.  If more than one input device is 
connected, press the SOURCE 
button and use ▲▼ to scroll among 
devices. 
(Component is supported through 
the RGB to COMPONENT 
ADAPTER.) 
 
 
Note: 
After powered on for 3 minutes, 
the projector goes into the ED 
(Extreme Dimming) mode if the 
source cannot be detected within 
30 seconds. 
 
 VGA1 / VGA2: Analog RGB 
 Composite Video: Traditional composite video 
 S-Video: Super video (Y/C separated) 
 HDMI: High-Definition Multimedia Interface