Vivitek Dw3321 User Manual

							— 
4  —   Rear view 
I TEM   L ABEL   D ESCRIPTION   S EE PAGE :  
1.   HDMI   1   /MHL   Connect the HDMI/MHL cable from a n   HDMI/MHL device .  
Note: Set 
the Source to HDMI 1/MHL also can be charging connected  MHL compatible smart device as long as the projector Power 
On.  
2.   HDMI   2   Connect the HDMI cable from a n   HDMI device .  
3.   RJ45 (HDBaseT)  
(Available in DW3321)   Connect an   RJ45 Cat5 e /Cat6 cable  for  HDBaseT signal received .  
4.   DVI - D   Connect the DVI CABLE to a display .  
5.   RS - 232   Connects RS - 232 serial port cable for remote control .  
6.   VGA OUT   Connect an   RGB cable to a display   (Pass through by VGA1 only) .  
7.   S - VIDEO   Connect a   S - VIDEO cable from a video device .  
8.   VGA 1   Connect a n   RGB cable from a computer or a video enabled device .  
9.   BNC   Connect a BNC cable from a computer .  
10.     VGA 2   Connect  an   RGB cable from a computer or a video enabled device .  
11.     RJ45 (LAN)   Connect a LAN cable  from Ethernet .  
12.     USB   Connect a   USB cable  for USB host .  
Note:   Support 5V/1.0A for each port output as long as the projector 
Power On.  
13.     3D - SYNC OUT   Connect 3D IR glasses receiver unit .  
14.     USB DISPLAY   Connect your projector to a PC through a USB cable .  
15.     Kensington ®
  Security Slot Secures to permanent object with a Kensington ®
  Lock
system .   70    
						

							 
– 5 – 
ITEM LABEL DESCRIPTION SEE PAGE: 
16.  AUDIO IN Connect an AUDIO cable from the input device. 
17.  IR Receive IR signal from remote control. 
18.  12V OUT 
When connected to the screen through a commercially available 
cable, the screen deploys automatically on start up of the projector. 
The screen retracts when the projector is powered off (see notes 
below). 
19.  AUDIO OUT Connect an AUDIO cable for audio loop through. 
20.  AUDIO OUT L/R Connect an AUDIO cable for audio loop through. 
21.  AUDIO IN L/R Connect the audio cables from an audio device for VIDEO or S-
VIDEO audio input. 
22.  VIDEO Connect the composite cable from a video device. 
23.  MICROPHONE Connect the microphone input device. 
24.  SERVICE For service personnel only. 
25.  WIRE REMOTE 
Connect the wire remote from remote control to the projector for wire 
remote control. 
Connect WIRE REMOTE OUT to another projector (same model) 
WIRE REMOTE IN for serial control. 
26.  AC IN Connect the POWER cable. 
 
Note: 
 To use this feature, you must plug in the connector before turn on/off the projector. 
 Screen controllers are supplied and supported by screen manufacturers. 
 Do not use this jack for anything other than intended use. 
 
 Warning: 
As a safety precaution, disconnect all power to the projector and connecting devices before making 
connections. 
   
						

							— 6 — 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Tilt Adjustor Rotate adjuster lever to adjust angle position. 14 
2.  Ceiling Mount Holes Contact your dealer for information on mounting the projector on a 
ceiling. 
 
Note: 
When installing, ensure that you use only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw 
depth of 6 mm (0.23 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount 
load capacity must exceed the weight of the installed equipment, and as an additional precaution 
be capable of withstanding three times the weight of the equipment (not less than 5.15 kg) over a 
period of 60 seconds.   
						

							 
– 7 – 
Remote Control Parts 
 
 Important: 
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
2. Be sure nothing obstructs the path between the remote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
3. The buttons and keys on the projector have the same functions as the corresponding buttons on 
the remote control. This user’s manual describes the functions based on the remote control. 
 
Note: 
Complies with FDA performance standards for laser products except for deviations pursuant to 
Laser Notice No. 50, dated June 24, 2007 
 
Caution: 
Use of controls, adjustments or performance of procedures other than those specified herein 
may result in hazardous laser light exposure.   ！  
						

							— 8 — 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR Transmitter Transmits signals to projector. 
2.  Power On Turns the projector on. 12 
3.  PC Displays the VGA1/VGA2/PC source selection (toggle). 
4.  HDMI Displays the HDMI 1/2 source selection (toggle). 
5.  USB Displays the USB source selection. 
6.  ▲ (Up Cursor) /  Navigates and changes settings in the OSD. 
Quick Menu – For Vertical Keystone. 20 
7.  MENU Opens the OSD. 20 
8.  ◄ (Left Cursor) /  Navigates and changes settings in the OSD. 
Quick Menu – For Horizontal Keystone. 20 
9.  Keystone Opens the Keystone menu. 
10.  ▼ (Down Cursor) /  Navigates and changes settings in the OSD. 
Quick Menu – For Vertical Keystone. 20 
11.  Laser Press to operate the on-screen pointer. DO NOT POINT IN EYES. 
12.  Play/Pause Play or pause video/music for MHL. 
13.  Reverse Reverse in set increments for MHL. 
14.  Prev Play the previous item on the programming list for MHL. 
15.  Stop Stop video/music playing for MHL. 
16.  Source/ID 
Alternate input source. 
Combo key function for Remote Control customer 
code settings (ID + Number). 
20 
17.  Auto/0 Auto adjustment for frequency, phase, and position. 
Number for Remote ID setting used. 20 
18.  Brightness Displays the brightness setting bar. 
19.  Lamp Displays the lamp selections. 
20.  Freeze Freezes/unfreezes the on-screen picture. 
21.  Blank/6 Makes the screen blank. 
Number for Remote ID setting used. 
22.  Laser Use as on-screen pointer. DO NOT POINT IN EYES. 
23.  Power Off Turns the projector off. 12 
24.  Video/S-Video Displays the VIDEO/S-VIDEO source selection. 
25.  Network Displays the Network source selection. 
26.  HDBaseT Displays the HDBaseT source selection. 
27.  EXIT Return to last OSD page. 
28.  ENTER Enters and confirms settings in the OSD. 20 
29.  ► (Right Cursor) /  Navigates and changes settings in the OSD. 
Quick Menu – For Horizontal Keystone. 20 
30.  MHL Enable the Mobile High-Definition Link technology feature for smart 
devices. 
31.  Forward Forward in set increments for MHL. 
32.  Next Play the following item on the programming list for MHL.      
						

							 
– 9 – 
ITEM LABEL DESCRIPTION SEE PAGE: 
33.  Volume/1 Displays the Volume setting bar. 
Number for Remote ID setting used. 
34.  Contrast/2 Displays the Contrast settings bar. 
Number for Remote ID setting used. 
35.  Mute/3 Mutes the built-in speaker. 
Number for Remote ID setting used. 
36.  Zoom/4 Displays the digital zoom settings bar. 
Number for Remote ID setting used. 18 
37.  3D/5 Enable 3D feature. 
Number for Remote ID setting used. 
38.  Status/7 
Opens the OSD Status menu (the menu only opens when an input 
device is detected). 
Number for Remote ID setting used. 
39.  Wired Jack Connect wire remote to the projector. 
Note: 
Remote Combo Key Settings: 
ID+0: Reset Remote Control customer code to default settings. 
ID+1: Set Remote Control customer code to 1. 
~ 
ID+7: Set Remote Control customer code to 7. 
 
Projector also need setting ID for unique control. Projector ID settings see page 37. 
 
Note: 
When the projector is under MHL mode, The keypad on projector should be with the same defini-
tion of the key on remote control. 
 
When MHL function: 
MENU for App settings, ▲ Up, ▼ Down, ◄ Left and ► Right are used as directional arrows, also 
included ENTER and EXIT. 
 
Controlling your smart device with the remote control: 
When the projector projects the contents from your MHL compatible smart device, you can use the 
remote control to control your smart device. 
To enter the MHL mode, the following buttons are available for controlling your smart device, Arrow 
keys (▲ Up, ▼ Down, ◄ Left, ► Right), MENU, EXIT, MHL control buttons.  
						

							— 10 — 
Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the 
rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 
degrees above or below the projector level. If the projector does not respond to the remote control, move a 
little closer. 
Projector and Remote Control Buttons 
The projector can be operated using the remote control or the buttons on the top of the projector. All 
operations can be carried out with the remote control; however, the buttons on the projector are limited in 
use.   
						

							 
– 11 – 
SETUP AND OPERATION 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment 
cover by sliding the cover in the direc-
tion of the arrow. 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
 Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
2. Dispose of used batteries according to local ordinance regulations. 
3. Remove the batteries when not using the projector for prolonged periods.      
						

							— 12 — 
Starting and Shutting down the Projector 
1.  Securely connect the power cord and 
signal cable. When connected, the power 
led will flash green to solid green. 
 
2.  Turn on the lamp by pressing “” 
button on the top of the projector or 
“” on the remote control. 
The PWR LED will now flash green. 
The startup screen will display in 
approximately 30 seconds. The first time 
you use the projector, you can select 
your preferred language from quick menu 
after the startup screen display. (See 
Setting the OSD Language on page 21) 
 
      
						

							 
– 13 – 
3.  If more than one input device is 
connected, press the SOURCE button 
and use ▲▼ to scroll among devices. 
(Component is supported through the 
RGB to Component adapter.) 
 
 HDMI 1 / MHL: High-Definition Multimedia Interface 
and Mobile High-Definition Link 
compatible 
 HDMI 2: High-Definition Multimedia Interface 
compatible 
 DVI: DVI 
 VGA 1 / 2: Analog RGB 
DVD input YCbCr/ YPbPr, or HDTV input 
YPbPr via D-sub connector 
 BNC: Analog RGB 
 VIDEO: Tradition composite video 
 S-Video: Super video (Y/C separated) 
 Network Display: Network Display Source 
 USB Reader: USB reader Source 
 USB Display: USB Display from PC USB connection 
 HDBaseT: Digital Video trough the Network 
transmitter (Available in DW3321) 
Note: The HDBaseT 5Play™ feature set enables 
delivering the signal over a single 100m / 328ft CAT5e / 
6 cable. 
4.  When the “Power Off? /Press Power 
again” message appears, press the 
POWER button. The projector turns off. 
 
 Caution: 
Do not unplug the power cord until the POWER LED stops flashing – indicating the projector has 
cooled down.