Vivitek D930tx Projector User Manual

							
TROUBLESHOOTING 
Common problems and solutions 
These guidelines provide tips to deal with problems you may encounter while using the projector. If 
the problem remains unsolved, contact your dealer for assistance. 
Often after time spent troubleshooting, the problem is traced to something as simple as a loose con-
nection. Check the following before proceeding to the problem-specific solutions. 
• Use some other electrical device to confirm that the electrical outlet is working. 
• Ensure the projector is turned on. 
• Ensure all connections are securely attached.  
• Ensure the attached device is turned on. 
• Ensure a connected PC is not in suspending mode. 
• Ensure a connected notebook computer is configured for an external display. 
(This is usually done by pressing a Fn-key combination on the notebook). 
Tips for Troubleshooting 
In each problem-specific section, try the steps in the order suggested. This may help you to solve the 
problem more quickly. 
Try to pin point the problem and thus avoid replacing non-defective parts.  
For example, if you replace batteries and the problem remains, put the original batteries back and go 
to the next step.  
Keep a record of the steps you take when troubleshooting: The information may be useful when call-
ing for technical support or for passing on to service personnel. 
 
— 45 —  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
LED Error Messages 
ERROR CODE MESSAGES POWER LED
BLINK 
READY LED 
BLINK 
TEMP LED 
BLINK 
Over temperature OFF OFF ON 
Thermal Break 4 OFF OFF 
G794 fail 4 4 OFF 
T1 fail 4 5 OFF 
Lamp error 5 OFF OFF 
Ballast Over Temperature 5 1 OFF 
Ballast shot circuit in output detected 5 2 OFF 
End of lamp lift detected 5 3 OFF 
Ballast lamp did not ignite 5 4 OFF 
Lamp extinguished during normal operation 5 5 OFF 
Lamp extinguished during run-up phase 5 6 OFF 
Lamp Memory write error 5 7 OFF 
Lamp Memory write buffer overflow 5 8 OFF 
Lamp UART buffer overflow 5 9 OFF 
Lamp current calculation error 5 10 OFF 
Lamp Corrupted software configuration 5 11 OFF 
Lamp voltage too low 5 12 OFF 
Lamp FLASH memory CRC error 5 13 OFF 
Lamp EEPROM memory CRC error 5 14 OFF 
Lamp EEPROM configuration does not match FLASH kernel 5 15 OFF 
Fan1 error (Lamp Fan) 6 1 OFF 
Fan2 error (Ballast Fan) 6 2 OFF 
Fan3 error (Burner Fan) 6 3 OFF 
Fan4 error (Power Fan) 6 4 OFF 
Lamp door open 7 OFF OFF 
DMD error 8 OFF OFF 
Color wheel error 9 OFF OFF 
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before re-
starting the projector. If the POWER or LAMP LEDs are still blinking or the TEMP LED is lit, contact 
your service center. 
Image Problems 
Problem: No image appears on the screen 
1. Verify the settings on your notebook or desktop PC. 
2. Turn off all equipment and power up again in the correct order. 
Problem: The image is blurred  
1. Adjust the Focus on the projector. 
2. Press the Auto button on the remote control or projector. 
– 46 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
3. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range. 
4. Check that the projector lens is clean. 
Problem: The image is wider at the top or bottom (trapezoid effect)  
1. Position the projector so it is as perpendicular to the screen as possib\
le.  
2. Use the Keystone button on the remote control or projector to correct the problem. 
Problem: The image is reversed  
Check the Projection setting on the Installation I menu of the OSD. 
Problem: The image is streaked  
1. Set the Frequency and Tracking settings on the Computer menu of the OSD to the de-
fault settings. 
2. To ensure the problem is not caused by a connected PC’s video card, connect to another 
computer.  
Problem: The image is flat with no contrast  
Adjust the Contrast setting on the Image menu of the OSD. 
Problem: The color of the projected image does not match the source imag\
e. 
Adjust the Color Temperature and Gamma settings on the Image menu of the OSD. 
Lamp Problems 
Problem: There is no light from the projector  
1. Check that the power cable is securely connected. 
2. Ensure the power source is good by testing with another electrical device. 
3. Restart the projector in the correct order and check that the Power LED is green. 
4. If you have replaced the lamp recently, try resetting the lamp connections.  
5. Replace the lamp module. 
6. Put the old lamp back in the projector and have the projector serviced. 
Problem: The lamp goes off 
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the READY LED 
is on, press the power button. 
2. Replace the lamp module. 
3. Put the old lamp back in the projector and have the projector serviced. 
Remote Control Problems 
Problem: The projector does not respond to the remote control  
1. Direct the remote control towards remote sensor on the projector.  
2. Ensure the path between remote and sensor is not obstructed. 
3. Turn off any fluorescent lights in the room. 
4. Check the battery polarity. 
5. Replace the batteries. 
6. Turn off other Infrared-enabled devices in the vicinity. 
7. Have the remote control serviced. 
 
– 47 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Audio Problems 
Problem: There is no sound 
1. Adjust the volume on the remote control.  
2. Adjust the volume of the audio source. 
3. Check the audio cable connection. 
4. Test the source audio output with other speakers. 
5. Have the projector serviced. 
Problem: The sound is distorted  
1. Check the audio cable connection. 
2. Test the source audio output with other speakers. 
3. Have the projector serviced. 
Having the Projector Serviced 
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in 
the original carton. Include a description of the problem and a checklist of the steps you took when 
trying to fix the problem: The information may be useful to service personnel. For servicing, return the 
projector to the place you purchased it. 
 
– 48 –  
						

							
— 49  — 
SPECIFICATIONS 
Specifications 
Model D935VX D940VX  D930TX 
Display type TI DMD .55” XGA  TI DMD 0.7” XGA  TI DMD 0.55” XGA 
Resolution XGA 1024x768 Native  XGA 1024x768 Native  XGA 1024x768 Native 
Weight 3.5 kg (7.7 lbs)  3.6 kg (7.9 lbs) 
Projection distance 1 meters ~ 10 meters  1 meters ~ 10 meters  0.5 meters ~ 5 meters 
Projection screen size 22.5”~300” 23.4”~300”  38”~380” 
Projection lens Manual Focus/Manual Zoom  Manual Focus 
Zoom ratio 1.2 0.65 
Vertical keystone  
correction +/- 15 degrees 
Projection methods Front, Rear, Desktop/Ceiling (Rear, Front) 
Data compatibility IBM PC or compatibles (VGA, SVGA, XGA, SXGA, UXGA), Mac 
SDTV/EDTV/ HDTV 480i, 576i, 480p, 576p, 720p, 1080i, 1080p 
Video compatibility NTSC/NTSC 4.43, PAL (B/G/H/I/M/N/60), SECAM 
H-Sync 15, 30 – 80 kHz 
V-Sync 43 – 87 Hz 
Safety certification FCC-B, UL, cUL, CB, CE, CCC, EK, PCT, PSB 
Operation temperature 5° ~ 35°C 
Dimensions 335 mm (W) x 102 mm (H) x 256 mm (D) 
AC Input AC Universal 100 ~ 240, Typical @ 110VAC (100~240)/+-10% 
Power consumption 290W 350W 
Stand By 
						

							
D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
– 50 –  
Projection Distance vs.  Projection Size 
 
D935VX / D940VX / D930TX Projection Distance and Size Table 
D935VX TELE WIDE 
Distance (m)  1.34 3.58 4.47 8.94 1.54 3.09 3.86 11.58 
Diagonal (inches)  30 80 100 200 40  80 100 300 
Keystone (degree)  12.3 12.3 12.3 12.3 14.2 14.2 14.2 14.2 
Image Height (mm)  457.2  1219.2  1524  3048  609.6  1219.2  1524  4572 
Image Width (mm)  609.6  1625.6  2032  4064  812.8  1625.6  2032  6096 
A (mm)  64 170.7 213.4 426.7 85.3 170.7 213.4 640.1 
 
D940VX TELE WIDE 
Distance (m)  1.28 3.41 4.27 8.53 1.46 2.93 3.66 10.97 
Diagonal (inches)  30 80 100 200 40  80 100 300 
Keystone (degree)  12.55 12.55 12.55 12.55 14.56 14.56 14.56 14.56 
Image Height (mm)  457.2  1219.2  1524  3048  609.6  1219.2  1524  4572 
Image Width (mm)  609.6  1625.6  2032  4064  812.8  1625.6  2032  6096 
A (mm)  56.4 150.5 188.1 376.3 75.3 150.5 188.1 564.4 
 
D930TX TELE 
Distance (m)  0.53  1.05  1.32  3.95 
Diagonal (inches)  40  80  100  300 
Keystone (degree)  34.9  34.9  34.9  34.9 
Image Height (mm)  609.6  1219.2  1524  4572 
Image Width (mm)  812.8  1625.6  2032  6096 
A (mm)  62.8  125.6  157  470.9  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
D935VX / D940VX / D930TX Timing Mode Table 
The projector can display several resolutions. The following table outlines the resolutions that can be 
displayed by the projector. 
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC
(HZ) 
COMPOSITE 
/ S-VIDEO COMPONENT RGB 
(ANALOG) 
DVI/ 
HDMI 
(DIGITAL)
NTSC — 15.734 60.0 O — － － 
PAL/SECAM — 15.625 50.0 O — － － 
720 x 400 37.9 85.0 — — O O 
640 x 480 31.5 60.0 — — O O 
640 x 480 37.9 72.8 — — O O 
640 x 480 37.5 75.0 — — O O 
640 x 480 43.3 85.0 — — O O 
800 x 600 35.2 56.3 — — O O 
800 x 600 37.9 60.3 — — O O 
800 x 600 46.9 75.0 — — O O 
800 x 600 48.1 72.2 — — O O 
800 x 600 53.7 85.1 — — O O 
1024 x 768 48.4 60.0 — — O O 
1024 x 768 56.5 70.1 — — O O 
1024 x 768 60.0 75.0 — — O O 
1024 x 768 68.7 85.0 — — O O 
1280 x 800 49.7 59.8 — — O O 
1280 x 800 62.8 74.9 — — O O 
1280 x 800 71.6 84.8 — — O O 
1280 x 1024 64.0 60.0 — — O O 
1280 x 1024 80.0 75.0 — — O O 
1280 x 1024 91.1 85.0 — — O O 
1400 x 1050 65.3 60.0 — — O O 
1440 x 900 55.9 60.0 — — O O 
VESA 
1600 x1200 75.0 60 — — O O 
640 x 480 35.0 66.7 — — O O 
832 x 624 49.7 74.5 — — O O 
1024 x 768 60.2 74.9 — — O O 
Apple  
Macintosh 
1152 x 870 68.7 75.1 — — O O 
480i 15.734 60.0 — O — O SDTV 576i 15.625 50.0 — O — O 
576p 31.3 50.0 — O — O EDTV 480p 31.5 60.0 — O — O 
 
– 51 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr———UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
SIGNAL RESOLUTION H-SYNC  
(KHZ) 
V-SYNC
(HZ) 
COMPOSITE 
/ S-VIDEO COMPONENT RGB 
(ANALOG) 
DVI/ 
HDMI 
(DIGITAL)
720p 37.5 50.0 — O — O 
720p 45.0 60.0 — O — O 
1080i 33.8 60.0 — O — O 
1080i 28.1 50.0 — O — O 
1080p 67.5 60.0 — O — O 
HDTV 
1080p 56.3 50.0 — O — O 
O: Frequency supported 
—: Frequency not supported 
The resolution of the panel for the D935VX / D940VX / D930TX is 1024 x 768. Resolution other than 
native resolution may display with uneven size of text or lines. 
– 52 –  
						

							
DDDLLLPPP   PPPrrrooojjjeeeccctttooorrr   –––   UUUssseeerrr’’’sss   MMMaaannnuuuaaalll   
Projector Dimensions 
 
 
 
 
– 53 –  
						

							
REGULATORY COMPLIANCE 
FCC Warning 
This equipment has been tested and found to comply with the limits for a Class B digital device pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. 
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause harmful interference in which 
case the user will be required to correct the interference at his/her own expense. 
Changes or modifications not expressly approved by the parties responsible for compliance could 
void the user’s authority to operate the equipment. 
Canada 
This class B digital apparatus complies with Canadian ICES-003. 
Safety Certifications 
FCC-B, UL, cUL, CB, CE, CCC, EK, PCT, and PSB 
EN 55022 Warning 
This is a Class B product. In a domestic environment, it may cause radio interference, in which case 
the user may be required to take adequate measures. The typical use is in a conference room, meet-
ing room, or auditorium. 
— 54 —