Vivitek D910hd User Manual

							DLP Projector—User’s Manual 
Views of Projector Parts  
Front-right View 
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  IR receiver Receive IR signal from remote control 
2.  Lens Projection  Lens 
3.  Focus ring Focuses the projected image 
4.  Zoom ring Enlarges the projected image 
16 
5.  Function keys  See Top view—On-screen Display (OSD) buttons 
and LEDs. 3 
Important: 
Ventilation openings on the projector 
allow for good air circulation, which keeps the projector lamp 
cool. Do not obstruct any of the ventilation openings. 
— 2 —  
						

							DLP Projector—User’s Manual 
Top view—On-screen Display (OSD) buttons and LEDs 
1
6
2
3
4
5
12 7
8
9
1
0
11 
ITEM LABEL DESCRIPTION SEE PAGE
1.  MENU 
Opens and exits OSD menus 
2.   Navigates in the OSD 
Quick Menu – For Keystone 
17 
3.  SOURCE 
Enter the Source menu 
4.   Navigates and changes settings in the OSD 17 
5.   Enter or confirm highlighted OSD menu item 
6.  AUTO 
Optimizes image size, position, and resolution 
7.   Navigates and changes settings in the OSD 
8.   Navigates in the OSD 
Quick Menu – For Keystone 
17 
9.   
Turns the projector On or Off 
10.  LAMP LED 
Flashing Error code 
Blue  Lamp Ready, Over Temperature  
11.  POWER LED 
Flashing Start, Cooling, Error code 
12.  TEMP LED  Red Over Temperature 
51 
 
– 3 –   
						

							DLP Projector—User’s Manual 
 Rear view 
1210
3
45678 9
11
12
13
14
15
16
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  AC IN  Connect the POWER cable 11 
2.  VGA IN  Connect the RGB cable from a computer 
3.  VGA IN  Connect the RGB cable from a computer 
4.   (USB) Connect the USB cable from a computer  
5.  VGA OUT 
Connect the RGB cable to a display 
6.  RS-232C Connect RS-232 serial port cable for remote control 
7.  DP  Connect a DISPLAYPORT CABL E from a DISPLAYPORT device 
8.  HDMI Connect the HDMI cable from a HDMI device 
9.  RJ45 Connect a LAN cable from Ethernet 
10.  Kensington Lock Secure to permanent object with a Kensington® Lock 
system 49 
11.  VIDEO IN  Connect the COMPOSITE cable from a video device 
12.  AUDIO IN (L and R)  Connect the AUDIO cable from a audio device 
13.  S-VIDEO   Connect the S-VIDEO cable from a video device 
14.  AUDIO IN Connect an AUDIO cable from the audio device 
15.  AUDIO OUT  Connect an AUDIO cable to audio amplifier 
16.  DC 12V TRIGGER When connected to the screen through 
a commercially available cable, 
the screen deploys automatically on st art up of the projector. The screen 
retracts when the projector is powered off (see notes below). 
Note: 
  To use this feature, you must plug in t he connector before turn on/off the projector. 
 Screen controllers are supplied and  supported by screen manufacturers. 
 Do not use this jack for any thing other than intended use. 
— 4 —  
						

							DLP Projector—User’s Manual 
– 5 –  
 
Note: 
If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the  
S-VIDEO connector. S-VIDEO provides a better quality signal. 
 
Warning: 
As a safety precaution, disconnect all power to  the projector and connecting devices before making 
connections. 
  
						

							DLP Projector—User’s Manual 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  Ceiling support holes Contact your dealer for information on mounting the projector on a 
ceiling 
2.  Tilt adjustor  
Rotate adjuster lever to adjust angle position.  15 
 
Note: 
When installing, ensure that you us e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting har dware and M4 screws with a maximum screw 
depth of 12 mm (0.47 inch).  
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount 
load capacity must exceed the  weight of the installed equipment, and as an additional precaution 
be capable of withstanding three times the weight  of the equipment (not less than 5.15 kg) over a 
period of 60 seconds. 
 
— 6 —  
						

							DLP Projector—User’s Manual 
Remote Control Parts  
 
Important: 
1. Avoid using the projector with bright fluore scent lighting turned on. Certain high-frequency 
fluorescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the  remote control and the projector. If the path 
between the remote control and the  projector is obstructed, you can bounce the signal off certain 
reflective surfaces such  as projector screens. 
 
3. The buttons and keys on the projector have the  same functions as the corresponding buttons on 
the remote control. This user’s manual descri bes the functions based on the remote control. 
– 7 –   
						

							DLP Projector—User’s Manual 
— 8 — 
ITEM LABEL DESCRIPTION SEE PAGE 
1.  IR transmitter  Transmits signals to projector 
2.  Status LED  Lights when the remote control is used 
3.  Laser Press to operate the on-screen pointer 
4.  Up Up arrow when connected through USB to a PC 
5.  Right  Right arrow when connected through USB to a PC 
6.  Down Down arrow when connected through USB to a PC 
7.  Page Down  Page down when connected through USB to a PC 
8.  Up cursor  Navigates in the OSD 
9.  Right cursor   Navigates and changes settings in the OSD 
10.  Down cursor Navigates in the OSD 
17 
11.  Volume +/-  Adjusts volume 16 
12.  Mute Mutes the built-in speaker 
13.  Zoom+ Zoom in  
14.  Zoom- Zoom  out 
15.  Freeze  Freeze/unfreezes the on-screen picture 
16.  Blank  Makes the screen blank 
17.  Source Detects the input device 
18.  Auto  Auto adjustment for phase, tracking, size, position 
19.  Menu Opens or exit the OSD  17 
20.  Status  Opens the OSD Status menu (the menu only opens 
when an input device is detected) 30 
21.  Keystone 
top/bottom Corrects image-trapezoid (wider top/bottom) effect 16 
22.  Left cursor 
Navigates and changes settings in the OSD   
23.  Enter Changes settings in the OSD 
24.  Page Up Page up when connected through USB to a PC 
25.  Left  Left arrow when connected through USB to a PC 
26.  Enter Enter key when connected through USB to a PC 
17 
27.  Power  Turns the projector on or off 11 
28.  Laser Use as on-screen pointer.  DO NOT POINT IN EYES. 
！Caution: 
Use of controls, adjustments or  performance of procedures other than those specified herein may 
result in hazardous laser light exposure. 
  
						

							DLP Projector—User’s Manual 
– 9 –  
Remote Control Operating Range 
The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a little closer.   
Projector and Remote Control Buttons 
The projector can be operated using t he remote control or the buttons on the top of the projector. All 
operations can be carried out with the remote control; however, the butt ons on the projector are 
limited in use.  
  
						

							DLP Projector—User’s Manual 
Inserting the Remote Control Batteries 
1.  Remove the battery compartment 
cover by sliding the cover in the 
direction of the arrow. 
 
2.  Insert the battery with the positive 
side facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for prolonged periods. 
 
 
— 10 —  
						

							DLP Projector—User’s Manual 
– 11  – 
SETUP AND OPERATION 
Starting and Shutting  down the Projector 
 
1.  Connect the power cord to the 
projector. Connect the other end to 
a wall outlet. 
The 
 POWER LED on the 
projector light. 
2.  Turn on the connected devices.  
3.  Ensure the POWER LED not a 
flashing. Then press the 
  POWER  
button to turn on the projector.  
 
The projector splash screen displays 
and connected devices are 
detected. 
 
See  Setting an Access Password 
(Security Lo
 ck) on page 13 if 
security lock is enabled.

 
4.  If more than one input device is 
connected, press the  SOURCE 
button and use ▲▼  to scroll among 
devices. 
(Component is supported through 
the RGB to COMPONENT 
ADAPTER.) 
 
 
   HDMI  : High-Definition Multimedia Interface 
   DisplayPort : Display Port 
   VGA 1 : Analog RGB 1 
   VGA 2 : Analog RGB 2 
   S-Video: Super video (Y/C separated) 
   Composite Video : Traditional composite video