Vivitek D871st User Manual

							
DLP Projector – User’s Manual 
– 33  – 
Advanced Feature 
Press the  Menu button to open the  OSD menu. Press  ◄► to move to the  Installation II menu. 
Press  ▲▼ to move to the  Advanced menu and then press  Enter or ►. Press  ▲▼ to move up and 
down in the  Advanced menu. Press  ◄► to change values for setting. 
 
ITEM DESCRIPTION 
OSD Menu Setting  Press Enter / 
► to enter the OSD setting menu. See page 34 for more information on  OSD 
Menu Setting . 
Peripheral Test  Press Enter/ 
► to enter the Peripheral Test menu. See page 34 for more information on 
Peripheral Test . 
Lamp Hour Reset  After replacing the lamp, this item should be reset. See page 35 for more information on
 Lamp 
Hour Reset . 
Low Power Mode  Press  ◄► to turn Low Power Mode on or off. 
3D Press Enter/  ► to enter the 3D menu. See page 35 for more information on  3D setting.. 
RS232 (*1)  Press 
◄► to select RS232 (remote) or Network (LAN) mode depending on projector connec-
tion method. 
Network (*2)  Press  (Enter) / 
► to enter the Network menu. See page 36 for more information on 
Network . 
Note: 
(*1) Not available in D860/D861 Series. 
(*2) Not available in D86 Series. 
 
Note: 
To enjoy the 3D function, fi rst enable the Play Movie in 3D setting found in your DVD  
device under the 3D Disc Menu. 
 
 
 
 
  
						

							DLP Projector—User’s Manual 
OSD Menu Setting  
 
ITEM DESCRIPTION 
Menu Position Press ◄► button to select different OSD location. 
Translucent Menu  Press ◄► button to select OSD background translucent level.  
Menu Display  Press ◄► button to select OSD timeout delay. 
Peripheral Test 
 
ITEM DESCRIPTION 
Remote Control Test  Press  (Enter) / ► to test the IR remote controller for diagnostic.  
Color Test  Press  (Enter) / ► to select different colors on screen. 
Button Test  Press  (Enter) / ► to test the button on keypad. 
USB Test (*)  Press  (Enter) / ► to test the USB connection with connected PC. 
Note: (*) Not available in D860/D861 Series. 
– 34 –   
						

							DLP Projector – User’s Manual 
Lamp Hour Reset 
 
Please refer to Resetting the Lamp  on page 44 to reset the lamp hour counter. 
 
 
3D 
 
ITEM DESCRIPTION 
3D Press  ◄► to select Off, DLP-Link or IR. 
3D Sync Invert  Press ◄► to turn 3D Sync Invert On or Off. 
 
 
 
 
 
 
 
 
 
– 35  –  
						

							DLP Projector—User’s Manual 
Network 
 
ITEM DESCRIPTION 
Network State Displays the network connection status. 
DHCP  Press 
◄► to turn DHCP On or Off.  
Note:  If you select DHCP Off, complete the IP  Address, Subnet Mask, Gateway, and DNS 
fields. 
IP Address   Enter a valid IP address if DHCP is turned off. 
Subnet Mask  Enter a valid Subnet Mask if DHCP is turned off. 
Gateway Enter a valid Gateway address if DHCP is turned off. 
DNS  Enter a valid DNS name if DHCP is turned off. 
Apply Press  (Enter) / ► to confirm settings. 
 
– 36 –   
						

							DLP Projector – User’s Manual 
For simplicity and ease of operation, the projector provides diverse networking and remote management 
features. 
The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off, 
Brightness and Contrast settings. Also, projector stat us information, such as: Video-Source, Sound-Mute, 
etc
. 
 
LAN_RJ45 
1.  Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 
 
2.  On the PC (Laptop), select  Start → Control  Panel →  Network Connections . 
 
– 37  –  
						

							DLP Projector—User’s Manual 
3. Right-click on Local Area Connection , and select Properties. 
 
4. In the  Properties  window, select the  General tab, and select  Internet Protocol (TCP/IP) . 
5. Click  Properties . 
 
6. Click  Use the following IP address  and fill in the IP address and Subnet mask, then click  OK. 
 
– 38 –   
						

							DLP Projector – User’s Manual 
7. Press the Menu button on the projector. 
8. Select  Installation II  →Advanced →Network. 
9.  After getting into  Network, input the following: 
  DHCP: Off 
  IP Address: 10.10.10.10 
  Subnet Mask: 255.255.255.0 
  Gateway: 0.0.0.0 
  DNS Server: 0.0.0.0 
10. Press 
 (Enter) / ►  to confirm settings. 
Open a web browser  
(for example, Microsoft Internet Explorer  with Adobe Flash Player 9.0 or higher). 
 
11.  In the Address bar, input  the IP address: 10.10.10.10. 
12. Press 
 (Enter) / ► . 
The projector is setup for remote managemen t. The LAN/RJ45 function displays as follows. 
 
–  39
  –  
						

							DLP Projector—User’s Manual 
 
CATEGORY ITEM INPUT-LENGTH 
IP Address 14 
IP ID 3 Crestron Control 
Port 5 
Projector Name 10 
Location 10 Projector 
Assigned To 10 
DHCP (Enabled) (N/A) 
IP Address 15 
Subnet Mask 15 
Default Gateway 15 
Network Configuration 
DNS Server 15 
Enabled (N/A) 
New Password 15 User Password 
Confirm 15 
Enabled (N/A) 
New Password 15 Admin Password 
Confirm 15 
 
For more information, please visit http://www.crestron.com. 
– 40 –  
						

							
DLP Projector – User’s Manual 
– 41  – 
 
Factory Reset 
Press the cursor  ▲▼ button to move up and down in the  Installation II menu. Select the  Factory 
Reset  sub menu and press 
 (Enter) /  ► to reset all the menu items to the factory default values 
(expect Language and Security Lock). 
 
Status 
Press the cursor  ▲▼ button to move up and down in the  Installation II menu. Select the   
Installation II  sub menu and press 
 (Enter) / ► to enter the  Status sub menu.
 
For D86 Series                                                             For D87 Series  
     
ITEM DESCRIPTION 
Active Source  Display the activated source. 
Video Information  Displays resolution/video information for RGB source and color standard for Video source. 
Lamp Hours Lamp hour used information is displayed.  
For D86 Series: Eco and Normal counters are separated. 
For D87 Series: Std. and Boost counters are separated. 
 
  
						

							DLP Projector—User’s Manual 
– 42 – 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified 
replacement part, which you can order from your local dealer.  
Important: 
a.  The projection lamp used in this product contains a small amount of mercury. 
b.  Do not dispose this product  with general household waste. 
c. Disposal of this product must be carried out in a ccordance with the regulations of your local  
authority. 
Warning: 
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to 
do so could result in a severe burn. 
 
Caution: 
In rare cases the lamp bulb may burn out during  normal operation and cause glass dust or shards 
to be discharged outward from the rear exhaust vent. 
Do not inhale or do not touch glass dust or shards. Doing so could result in injury.  
Always keep your face away from the exhaust vent  so that you do not suffer from the gas and bro-
ken shards of the lamp. 
When removing the lamp from a ceiling-mounted proj ector, make sure that no one is under the pro-
jector. Glass fragments could fall if the lamp has been burned out.  
！ IF A LAMP EXPLODES 
If a lamp explodes, the gas and broken shards may scatter inside the projector and they may come 
out of the exhaust vent. The gas contains toxic mercury. 
Open windows and doors for ventilation. 
If you inhale the gas or the shards  of the broken lamp enter your eyes or mouth, consult the doctor 
immediately.  
1.  Loosen the single screw on 
the lamp compartment cover.