Vivitek D865w User Manual

DLP Projector—User’s Manual 
Lamp Hour Reset 
 
Please refer to Resetting the Lamp  on page 47 to reset the lamp hour counter. 
 
Network 
 
ITEM DESCRIPTION 
Network State  Displays the network connection status. 
DHCP  Press 
◄► to turn DHCP On or Off. 
Note:  If you select DHCP Off, complete the IP  Address, Subnet Mask, Gateway, and 
DNS fields. 
IP Address   Enter a valid IP address if DHCP is turned off. 
Subnet Mask  Enter a valid Subnet Mask if DHCP is turned off. 
Gateway  Enter a valid Gateway...

DLP Projector—User’s Manual 
LAN_RJ45 
 
Wired LAN Terminal functionalites 
Remote control and monitoring of a projector from a PC (or Laptop) via wired LAN is also possible. 
Compatibility with Crestron / AMX (Device Discovery) / Extron control boxes enables not only collective 
projector management on a network but also management from a control panel on a PC (or Laptop) 
browser screen. 
   Crestron is a registered tra demark of Crestron Electronics, Inc. of the United States. 
   Extron is a...

DLP Projector—User’s Manual 
LAN_RJ45 
1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 
 
2. On the PC (Laptop), select  Start → Control  Panel →  Network Connections . 
 
— 34 —  

DLP Projector—User’s Manual 
3. Right-click on Local Area Connection , and select Properties. 
 
4. In the  Properties  window, select the  General tab, and select  Internet Protocol (TCP/IP) . 
5. Click  Properties . 
 
6. Click  Use the following IP address  and fill in the IP address and Subnet mask, then click  OK. 
 
– 35  –  

DLP Projector—User’s Manual 
7. Press the Menu button on the projector. 
8. Select  Settings2→ Advanced1  → Network 
9.  After getting into  Network, input the following: 
  DHCP: Off 
  IP Address: 10.10.10.10 
  Subnet Mask: 255.255.255.0 
  Gateway: 0.0.0.0 
  DNS Server: 0.0.0.0 
10. Press 
 (Enter) / ►  to confirm settings. 
Open a web browser  
(for example, Microsoft Internet Explorer  with Adobe Flash Player 9.0 or higher). 
 
11.  In the Address bar, input  the IP address: 10.10.10.10. 
12....

DLP Projector—User’s Manual 
 
 
CATEGORY ITEM INPUT-LENGTH 
IP Address 15 
IP ID 3 Crestron Control 
Port 5 
Projector Name 10 
Location 10 Projector 
Assigned To 10 
DHCP (Enabled) (N/A) 
IP Address  15 
Subnet Mask 15 
Default Gateway 15 
Network Configuration 
DNS Server 15 
Enabled (N/A) 
New Password 10 User Password 
Confirm 10 
Enabled (N/A) 
New Password 10 Admin Password 
Confirm 10 
For more information, please visit  http://www.crestron.com. 
– 37  –  

DLP Projector—User’s Manual 
Preparing Email Alerts  
1.  Make sure that user can access the homepage of LAN RJ45 function by web browser (for ex-
ample, Microsoft Internet Explorer v6.01/v8.0).  
2.  From the Homepage of LAN/RJ45, click  Alert Settings.  
 
3.  By default, these input boxes in  Alert Settings are blank.  
 
— 38 —  

DLP Projector—User’s Manual 
4. For Sending alert mail, input the following: 
The 
　 SMTP  field is the mail server for sending out email  (SMTP protocol). This is a required field. 
The 
　 To field is the recipient’s email address (for exam ple, the projector administrator). This is a 
required field.  
The 
　 Cc field sends a carbon copy of the alert to th e specified email address. This is an optional 
field (for example, the projecto r administrator’s assistant).  
The 
　 From field is the...

DLP Projector—User’s Manual 
RS232 by Telnet Function 
Besides projector connected to RS232 interface with “Hyper-Ter minal” communication by dedicated 
RS232 command control, there is alternative RS232 command control way, so called “RS232 by 
TELNET” for LAN/RJ45 interface. 
Quick Start-Guide for “RS232 by TELNET” 
Check and get the IP-Address on OSD of the projector. 
Make sure that laptop/PC can acce ss the web-page of the projector. 
Make sure that “Windows Firewall” setting to be di sabled in case...

DLP Projector—User’s Manual 
Input the command format like the below: 
telnet  ttt.xxx.yyy.zzz  23 (“Enter” key pressed) 
( ttt.xxx.yyy.zzz : IP-Address of the projector) 
If Telnet-Connection ready, and us er can have RS232 command inpu t, then “Enter” key pressed, 
the RS232 command will be workable. 
 
How to have TELNET enabled in Windows VISTA / 7 
By default installation for Windows VISTA, “TELNE T” function is not included. But end-user can 
have it by way of “Turn Windows features On or Off” to...