Home > Vivitek > Projector > Vivitek D791st User Manual

Vivitek D791st User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Vivitek D791st User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 263 Vivitek manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							
    DLP Projector – User’s Manual 
     
     
    5.  You can use the cursor buttons  ▲▼◄► 
    either on keypad or IR remote control for 
    password entry. You can use any 
    combination including the same arrow five 
    times, but not less than five. 
     
    Press the cursor buttons in any order to set 
    the password. Push the  MENU button to 
    exit the  dialog box. 
     
    6.  The password confirm menu appears when 
    user presses the power-on key in case the 
    Security Lock  is enabled.  
    Enter the password in the order you set it 
    at step 5. In case you forget the password, 
    please contact the service center.  
    The service center will validate the owner 
    and help reset the password.  
     
     
     
     
     
    –  13  – 
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    							
    DLP Projector – User’s Manual 
     
     
    Adjusting the Projector Level 
    Take note of the following when setting up the projector: 
    •  The projector table or stand should be level and sturdy. 
    • Position the projector so that it is perpendicular to the screen. 
    • Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection  
    angle. 
    • Ensure the cables are in a safe location. You could trip over them.  
     
    1.  To raise the level of the projector, twist 
    the adjusters clockwise. 
     
    2.  To lower the level of the projector, lift 
    the projector and twist the adjusters 
    counter clockwise. 
     
     
    – 14 –  
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    							
    DLP Projector – User’s Manual 
     
     
    Adjusting the Keystone 
    1.  
    Volume
    +
    -
    Use the  KEYSTONE  
    buttons the remote control 
    to correct image-trapezoid 
    (wider top or bottom)  
    effect. 
     
    2.  The keystone control  
    appears on the display. 
    –  15  – 
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    							
    DLP Projector – User’s Manual 
     
     
    Adjusting the Volume 
    1.  
    Volume
    +
    -
    Press the  Volume +/-   
    buttons on the remote 
    control.  
    The volume control  
    appears on the display. 
     
     
    2.  Press the  MUTE button to 
    turn off the volume 
     
     
    – 16 –  
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    							
    DLP Projector – User’s Manual 
     
     
     
    ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
    OSD Menu Controls 
    The projector has an OSD that lets you ma ke image adjustments and change various settings.  
    Navigating the OSD 
    You can use the remote control curs or buttons or the buttons on the top of the projector to navigate 
    and make changes to the OSD. The following illu stration shows the corresponding buttons on the 
    projector. 
     
    1.  To enter the OSD, press the  MENU button.  
    2.  There are five menus. Press 
    the cursor  ◄► button to 
    move through the menus.  
    3. Press the cursor  ▲▼ button 
    to move up and down in a 
    menu.  
    4. Press  ◄► to change values 
    for settings. 
    5. Press  MENU to close the 
    OSD or leave a submenu. 
    Note: 
    Depending on the video source, not all items in  the OSD are available. For example, the Horizon-
    tal/Vertical Position  items in the Computer menu can only be modified when connected to a PC. 
    Items that are not available cannot  be accessed and are grayed out.  
    – 17  – 
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    							
    DLP Projector – User’s Manual 
     
     
    Setting the OSD Language 
    Set the OSD language to your pr eference before continuing. 
    1.  Press the  MENU button. Press the cursor  ◄► button to navigate to Installation I. 
     
    2.  Press the cursor  ▲▼ button until  Language is highlighted.  
     
    3.  Press the cursor  ◄► button until the language you want is highlighted.  
    4.  Press the  MENU button twice to close the OSD.   
    – 18 – 
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    							
    DLP Projector – User’s Manual 
     
     
    –  19  – 
    OSD Menu Overview 
    Use the following illustration to quickly find a se tting or determine the range for a setting. 
     
     
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    							
    DLP Projector – User’s Manual 
     
     
    OSD Sub-Menu Overview 
     
    – 20 –  
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    							
    DLP Projector – User’s Manual 
     
     
    Image Menu  
    Press the MENU  button to open the  OSD menu. Press the cursor  ◄► button to move to the  Image 
    Menu. Press the cursor  ▲▼ button to move up and down in the  Image menu. Press  ◄► to change 
    values for settings. 
     
    ITEM DESCRIPTION 
    Display Mode Press the cursor  ◄► button to set the Display Mode.  
    Brilliant Color Press the cursor  ◄► button to adjust the Brilliant Color value. 
    Brightness Press the cursor ◄►  button to adjust the display brightness. 
    Contrast Press the cursor ◄► button to adjust the display contrast. 
    Sharpness Press the cursor  ◄► button to adjust the display sharpness level. 
    Gamma Press the cursor  ◄► button to adjust the gamma correction of the display.  
    – 21  – 
    Advanced Press  (Enter) /  ► to enter the Advanced menu. See  Advanced Feature on page 22. 
    Reset Press  (Enter) / ► to reset all settings to default values. 
     
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    							
    DLP Projector – User’s Manual 
     
     
    Advanced Feature 
    Press the Menu button to open the  OSD menu. Press  ◄► to move to the  Image menu. Press  ▼▲ 
    to move to the  Advanced menu and then press  Enter or ►. Press  ▼▲ to move up and down in the 
    Advanced  menu. 
     
    ITEM DESCRIPTION 
    Press the cursor ◄► button to adjust the color space.  Color Space  
    Press the cursor ◄► button to adjust the color temperature.  Color Temperature  
     for more information on   (Enter) / ► to enter the color manager menu. See page 23Press Color Manager  Color Manager.  
     
    – 22 –  
    Downloaded From projector-manual.com Vivitek Manuals 
    						
    All Vivitek manuals Comments (0)

    Related Manuals for Vivitek D791st User Manual