Vivitek D732mx User Manual

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r  
 
  –
–
–  
 
  U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Config Menu  
Press the  Menu button to open the  Main menu. Press the cursor  W X  button to move to the  Config 
menu. Press the cursor  ST button to move up and down in the  Config menu. Press  W X  to change 
values for settings, and then press  Enter or X
 to confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT 
Blank Screen  Press the cursor 
W X  button to select a background color for the blank 
screen.  
(Range: Black – Red – Green – Blue – White)   Blue 
Auto Source Press the cursor 
W X  button to enable or disable automatic source detec-
tion.  
(Range: On – Off)  On 
Auto Power 
Off Press the cursor 
W X  button to enable or disable automatic shut-down of 
lamp after 10 minutes of inactivity.  
(Range: On – Off)  Off 
Volume 
Press the cursor 
W X  button to adjust the audio volume level.  
(Range: 0 - 8)  4 
Menu  
Position Press the cursor 
W X  button to position the OSD on screen.  
(Range: Left – Right – Center – Down – Up)  Center 
Menu Display Press the cursor 
W X  button to determine the timeout delay of the OSD.  
(Range: 10 – 20 sec.)  15 
Translucent 
Menu Press the cursor 
W X  button to set menu screen translucency.  
(Range: 0% – 100%)  0% 
Reset 
Resets all Config items to default values   
 
Note: 
The Config menu functions are available to all video sources. 
– 25  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Utility Menu  
Press the  Menu button to open the  Main menu. Press the cursor  W X  button to move to the Utility 
menu. Press the cursor  ST button to move up and down in the  Utility menu. Press  W X  to change 
values for settings, and then press  Enter or X
 to confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT 
Video Type  Press the cursor 
W X  button to select the video standard  
(Range: Auto – NTSC – PAL – SECAM)  Auto 
Video AGC Press the cursor 
W X  button to enable or disable automatic 
gain control for the video source.  
(Range: On – Off)  On 
Press the cursor 
W X  button to choose from four projection 
methods: 
  Desktop mount, front of screen 
 Desktop mount, rear of screen 
 Ceiling mount, front of screen 
Projection 
 Ceiling mount, rear of screen  Desktop front 
 
Frequency 
Press the cursor 
W X  button to adjust the A/D sampling 
clock.  
(Range: 0° - 180°)  Auto detected 
Tracking 
Press the cursor 
W X  button to adjust the A/D sampling 
number.  
(Range: 1 - 100)  Auto detected 
– 26 –
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r  
 
  –
–
–  
 
  U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
–  27  – 
ITEM DESCRIPTION DEFAULT 
Digital Zoom  Digital operation for zoom and pan adjustment.  
Press 
Enter  or X
. The Zoom menu appears. 
 
Press  S
 to zoom in; press 
T
 to zoom out. Press 
Enter or 
X  to open the Pan menu. (You must zoom in before you 
can open the Pan menu.)  
 
Use the cursor buttons to pan the zoomed image. Press the 
Menu button to exit.  — 
Reset 
Resets Video Type, Video AGC, Projection, and Digital 
Zoom to default values  — 
Utility Menu Functions Available for Connected Source 
Function RGB DVI Component Video Composite Video S-video 
Video Type 
   O O 
Video AGC     O O 
Projection  O O O O O 
Frequency  O  O   
Tracking  O     
Digital Zoom  O  O O O 
Reset  O O O O O 
O = available to video source 
Downloaded From projector-manual.com Vivitek Manuals 
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Tool Menu  
Press the  Menu button to open the  Main menu. Press the cursor  W X  button to move to the Tool  
menu. Press the cursor  ST button to move up and down in the  Tool menu. Press  Enter or X
 to 
confirm the new setting. 
 
ITEM DESCRIPTION DEFAULT 
Language  Press the cursor W X  to select the desired language  English 
Remote control test Follow on-screen prompts to carry out the remote control test. You are re-
turned to the Tool menu at the end or by pressing the Menu button. 
USB test Follow on-screen prompts to carry out th
e USB test. You are returned to the 
Tool menu at the end or by pressing the Menu button. 
Button test  Follow on-screen prompts to carry out the button test. You are returned to 
the Tool menu at the end or by pressing the Menu button. 
Color test Follow on-screen prompts to carry out th
e color test. You are returned to the 
Tool menu at the end or by pressing the Menu button. 
Sound test  Follow on-screen prompts to carry out the sound test. You are returned to the 
Tool menu at the end or by pressing the Menu button. 
 
– 28 –
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r  
 
  –
–
–  
 
  U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Status Menu  
Press the  Menu button to open the  Main menu. Press the cursor  W X  button to move to the  Status 
menu. Press the cursor  ST button to move up and down in the  Status menu. 
 
ITEM DESCRIPTION DEFAULT 
Video  
Information  Displays the resolution and refresh rate for RGB/DVI mode. 
Displays the color standard for video mode. 
Active Source 
Displays the active source. 
Software 
Version Displays information about the software version. 
Lamp Hours Shows the number of hours the lamp has been in use for Eco and Normal 
modes. 
Note: 260w/280w are only for Normal and Eco modes.  These 
items are 
display on-
ly. 
Lamp Mode 
Press the cursor 
W X  button to choose the lamp mode.  
(Range: Eco, Normal, Boost)  
Note: 260w/280w are only for Normal and Eco modes. 
Eco mode uses less power and extends lamp life, but decreases lamp 
brightness.   Normal 
Lamp Hour  
Reset 
After replacing the lamp, this item shoul
d be reset. Refer to “Replacing the Pro-
jection Lamp” on page  30.  — 
–
 29  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							 – 30 – 
MAINTENANCE AND SECURITY 
Replacing the Projection Lamp 
The projection lamp should be replaced when it burns out. It should only be r eplaced with a certified 
replacement part, which you can order from your local dealer.  
 
Caution: 
When removing the lamp from a ceiling-mounted proj ector, make sure that no one is under the pro-
jector. Glass fragments could fall if the lamp has been burned out. 
 
Important: 
1. The lamp contains a certain am ount of mercury and should be dis posed of according to local or-
dinance regulations. 
2. Avoid touching the glass surface of the new  lamp: Doing so may shorten its operation life. 
 
Warning: 
Be sure to turn off and unplug the projector at l east an hour before replacing the lamp. Failure to do 
so could result in a severe burn. 
 
1.  Loosen the two captive 
screws on the lamp 
compartment cover (A). 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r  
 
  –
–
–  
 
  U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
2.  Open the lamp com-
partment cover ( B). 
 
3.  Remove the two screws 
from the lamp module 
(C). 
4.  Lift the module handle 
up ( D). 
 
–  31  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
5.  Pull firmly on the mod-
ule handle to remove the 
lamp module ( D) 
 
 
6.  Reverse steps 1 to 5 to 
install the new lamp 
module.  
 
– 32 –  
Downloaded From projector-manual.com Vivitek Manuals 
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r  
 
  –
–
–  
 
  U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Resetting the Lamp 
After replacing the lamp, you should reset the lamp  hour counter to zero. Refer to the following: 
1.  Press the Menu button to open the 
Main menu. 
2.  Press the cursor  W X  button
 to move 
to the  Status  menu. 
3.  Press the cursor  ST button
 to move 
down to  Lamp Hour Reset . 
 
4.  Press the cursor X or Enter  button.  
A message screen appears. 
5.  Press the cursor buttons in this order: 
T ; S ; W; X.
 
The  Status  menu appears again 
showing the  Lamp Hours  reset to 
zero.  
Cleaning the Projector 
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.  
Warning: 
1.  Be sure to turn off and unplug the projector at least an hour before cleaning. Failure to do so 
could result in a severe burn. 
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings 
on the projector.  
3. If a little water gets into the projector interior  while cleaning, leave unplugged in a well-ventilated 
room for several hours before using. 
4. If a lot of water gets into the projector inte rior when cleaning, have the projector serviced. 
– 33  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							D
D
D L
L
L P
P
P  
 
  P
P
P r
r
r o
o
o j
j
j e
e
e c
c
c t
t
t o
o
o r
r
r —
—
— U
U
U s
s
s e
e
e r
r
r ’
’
’ s
s
s  
 
  M
M
M a
a
a n
n
n u
u
u a
a
a l
l
l  
 
 
Cleaning the Lens 
You can purchase optic  lens cleaner from most camera stores . Refer to the following to clean the pro-
jector lens. 
1.  Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.) 
2.  Lightly wipe the lens in a circular motion. 
Caution: 
1.  Do not use abrasive cleaners or solvents. 
2. To prevent discoloration  or fading, avoid getting cleaner on the projector case. 
Cleaning the Case 
Refer to the following to clean the projector case. 
1.  Wipe off dust with a clean dampened cloth. 
2.  Moisten the cloth with warm water and mild dete rgent (such as used to wash dishes), and then wipe 
the case. 
3.  Rinse all detergent from the cloth and wipe the projector again. 
Caution: 
To prevent discoloration or fading of the case, do not use abrasive  alcohol-based cleaners. 
Using the Kensington® Lock 
If you are concerned about security, attach the projector to a permanent object with the Kensington 
slot and a security cable.  
 
 
 
Note: 
Contact your vendor for details on purchasing a suitable Kensi ngton security cable.  
The security lock corresponds to Kensington’s Micr oSaver Security System. If you have any com-
ment, contact: Kensington, 2853 Campus Drive, San Mateo, CA94403, U.S.A. Tel: 800-535-4242, 
http://www.Kensington.com. 
 
– 34 – 
Downloaded From projector-manual.com Vivitek Manuals