Vivitek D7180hd User Manual

DLP Projector – User’s Manual 
 
 
Views of Projector Parts  
Front-right View 
123456 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Lamp cover  Removes cover to replace lamp 
2.  Kensington lock  Secure to permanent obj
ect with a Kensington® 
Lock system 42 
3.  Security bar  For security and authorized usage 42 
4.  Lens Projection  Lens 
5.  Aspheric mirror Reflects images 
WARNING LED  Red 
Over Temperature 
LAMP LED  Flashing Error code 6.  
POWER LED  Flashing Error code 
46 
Important: 
Ventilation...

DLP Projector – User’s Manual 
 
 
 Rear view 
1234 5
678910 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  VGA OUT  Connect the RGB cable to a display 
(Loop Thru only for VGA IN) 
2.  VGA IN 
Connect the RGB cable from a computer and components. 
3.  DVI  Connect the DVI cable from a device. 
4.  HDMI Connect the HDMI cable from a HDMI device 
5.  USB  Connect the USB cable from a computer  
6.  RJ – 45  Connect a LAN cable from Ethernet 
7.  AC IN Connect the POWER cable 9 
8.  AUDIO OUT Connect an audio...

DLP Projector – User’s Manual 
 
 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Security bar  Helps protect the projector from unauthorized use 42 
2.  Tilt adjustors Rotate adjusters lever to adjust angle position 
3.  Ceiling support holes  Contact your dealer for information on mounting the projector on a ceiling 
 
Note: 
When installing, ensure that you us e only UL Listed ceiling mounts. 
For ceiling installations, use approved mounting har dware and M4 screws with a maximum screw 
depth of...

DLP Projector – User’s Manual 
 
 
Remote Control Parts 
 
 
Important: 
1.  Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the re mote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on...

DLP Projector – User’s Manual 
 
 
—  6 — 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  IR transmitter  Transmits signals to projector 
2.  Status LED  Lights when the remote control is used 
3.  Laser Press to operate the on-screen pointer 
4.  Up Up arrow when connected through USB to a PC 
5.  Right  Right arrow when connected through USB to a PC 
6.  Down  Down arrow when connected through USB to a PC 
7.  Page Down  Page down when connected through USB to a PC 
8.  Up cursor  
9.  Right cursor  
10.  Down...

DLP Projector – User’s Manual 
 
 
–  7 –  
Remote Control Operating Range 
The remote control uses infrared transmission to cont rol the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a...

DLP Projector – User’s Manual 
 
 
—  8 — 
SETUP AND OPERATION 
Inserting the Remote  Control Batteries  
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow. 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use AAA batteries (Alkaline batteries are recommended). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the batteries when not usi ng the projector for...

DLP Projector – User’s Manual 
 
 
Starting and Shutting  down the Projector 
1.  Connect the power cord to the projector. 
Connect the other end to a wall outlet. 
The POWER  LED will be on. 
2.  Turn on the connected devices.  
3.  Ensure the  POWER LED displays a 
solid amber and not a flashing amber. 
Then press the 
  POWER  button on 
the remote control to turn on the projec-
tor.  
The projector splash screen displays and 
connected devices are detected. 
4.  If more than one input device is con-...

DLP Projector – User’s Manual 
 
 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
•   The projector table or stand should be level and sturdy. 
•   Position the projector so that it is perpendicular to the screen. 
•   Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection  
angle. 
•   Ensure the cables are in a safe location. You could trip over them.  
 
1.  To lower the level of the projector, twist 
the adjusters clockwise....

DLP Projector – User’s Manual 
 
 
Adjusting the Keystone 
1.  Use the  KEYSTONE  
buttons on the remote 
control to correct image-
trapezoid (wider top or 
bottom) effect. 
 
2.  The keystone control  
appears on the display. 
Adjusting the Volume 
1.  Press the  Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
 
2.  Press the  MUTE button to 
turn off the volume 
 
–  11  –