Vivitek D558 User Manual

							— 12 — 
5.  You can use the cursor buttons 
▲▼◄► 
either on keypad or IR remote control 
for password entry. You can use any 
combination including the same arrow 
five times, but not less than five. 
Press the cursor buttons in any order 
to set the password. Push the MENU 
button to exit the dialog box. 
 
 
6.  The password confirm menu appears 
when user presses the power-on key 
in case the Security Lock is enabled.  
Enter the password in the order you 
set it at step 5. In case you forget the 
password, please contact the service 
center.  
The service center will validate the 
owner and help reset the password.   
 
 
 
 
  
						

							– 13 – 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
 The projector table or stand should be level and sturdy. 
 Position the projector so that it is perpendicular to the screen. 
 Ensure the cables are in a safe location. You could trip over them.  
 
To adjust the angle of the picture, turn the tilt-adjuster right or left until the desired 
angle has been achieved. 
 
 
 
   
						

							— 14 — 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom  
control (on the projector 
only) to resize the 
projected image and 
screen size . 
 
2.  Use the Image-focus  
control (on the projector 
only) to sharpen the 
projected image . 
3.  Use the KEYSTONE 
buttons the remote 
control to correct 
image-trapezoid (wider 
top or bottom) effect. 
 
4.  The keystone control 
appears on the display.  
Adjusting the Volume 
1.  Press the Volume +/- 
buttons on the remote 
control.  
The volume control 
appears on the display. 
 
 
2.  Press the MUTE button 
to turn off the volume. 
(This feature is available 
only on the remote).  
Note : Available in 
different model 
       
						

							– 15 – 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you make image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control cursor buttons to navigate and make changes to the OSD.  
 
1. To enter the OSD, press the 
MENU button.  
2. There are three menus. 
Press the cursor ◄► button 
to move through the menus.  
3. Press the cursor ▲▼ button 
to move up and down in a 
menu.  
4. Press ◄► to change values 
for settings. 
5. Press MENU to close the 
OSD or leave a submenu. 
 
Note: 
Depending on the video source, not all items in the OSD are available. For example, the 
Horizontal/Vertical Position items in the Computer menu can only be modified when connected 
to a PC. Items that are not available cannot be accessed and are grayed out.  
 2
Me nuP ow er
Volume
F r ee ze
A ut oS our c e
1
1
3
4
5
1
3
2
1
4
5
Mu t e  
						

							— 16 — 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1. Press the MENU button. Press the cursor ◄► button to navigate to Settings 1. Press the 
cursor ▲▼ button to move to the Advanced 1 menu. 
 
2. Press  (Enter) / ► to enter the Advanced 1 sub menu. Press the cursor ▲▼ button 
until Language is highlighted.  
 
3. Press the cursor button until the language you want is highlighted.  
4. Press the MENU button four times to close the OSD.   
   
						

							– 17 – 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
Main 
Menu 
 
Sub Menu   
 
Settings 
Image  Display Mode    Presentation, Bright, Game, 
Movie, TV, sRGB, Blackboard, 
User 
  Brightness    0~100 
  Contrast    0~100 
  Computer  Horizontal Position  -5~5 (depend on Autolock) 
    Vertical Position  -5~5 (depend on Autolock) 
    Frequency  0~31 
    Tracking  -5~5 
  Auto Image     
  Advanced  Brilliant Color  1~10 
    Sharpness  0~31 
    Gamma  1.8, 2.0, 2.2, 2.4, B&W, Linear 
    Color Temperature  Warm, Normal, Cold 
    Video AGC  Off, On 
    Video Saturation  0~100 
    Video Tint  0~100 
    White Balance RGain 0~200 
     GGain 0~200 
     BGain 0~200 
     ROffset -256~255 
     GOffset -256~255 
     BOffset -256~255 
  Color Manager  Red Hue, Saturation, Gain 0~100 
    Green Hue, Saturation, Gain 0~100 
    Blue Hue, Saturation, Gain 0~100 
    Cyan Hue, Saturation, Gain 0~100 
    Magenta Hue, Saturation, Gain 0~100 
    Yellow Hue, Saturation, Gain 0~100 
    White Red, Green, Blue 0~100 
  
						

							— 
18  —   Main 
Menu   Sub Menu   Settings  
S ettings 1     Source   Source   reference Input Source Select (IR/Keypad)  
Projection   Normal, Real, Ceiling, Real+Ceiling  
Aspect Ratio   Fill, 4:3, 16:9, Letter Box, Native,  
Theater  Zoom  
Keystone   - 40~40  
Digital Zoom   - 10~10  
Audio   Volume   0~10 
Mute   Off, On  
Advanced 1   Language   English, Français, Deutsch, Españ ol, 
Portuguê s,  簡体中文 ,  繁體中文 , Italiano, 
Norsk, Svenska, Nederlands, Русский, 
Polski, Suomi, Ελληνικά,  한국어 , Magyar, 
Čeština,  ةيبرعلا , T
						

							– 19 – 
Main 
Menu 
 
Sub Menu   
 
Settings 
Settings 2  Auto Source    Off, On 
  No Signal 
Power Off 
(min) 
   0~180 
  Auto Power 
On 
   Off, On 
  Lamp Mode    ECO, Normal, Dynamic Eco 
  Reset All     
  Status  Active Source   
    Video Information   
    Lamp Hours(ECO, Normal)   
    Software Version   
  Advanced 1  Menu Position  Center, Down, Up, Left, Right 
    Translucent Menu  0%, 25%, 50%, 75%, 100% 
    Low Power Mode  Off, On 
    Fan Speed  Normal, High 
    Lamp Hour Reset   
    Projector ID  0-98 
  Advanced 2  Sleep Timer (min)  0~600 
    Source Filter VGA Disable, Enable 
     HDMI/MHL Disable, Enable 
    Wall Color  Off, Light Yellow, Pink, Light 
Green, Blue, blackboard 
    Color Space  Auto, RGB, YUV 
    Quantization Range  Auto, Full, limit 
 
   
						

							— 20 — 
Image Menu  
 Attention !   
All of display mode parameters when changed will be saved to user mode.  
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image 
Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to enter 
and change values for settings. 
 
ITEM DESCRIPTION 
Display Mode Press the cursor ◄► button to enter and set the Display Mode.  
Brightness Press the cursor ◄► button to enter and adjust the display brightness. 
Contrast Press the cursor ◄► button to enter and adjust the display contrast. 
Computer Press  (Enter) / ► to enter the Computer menu. See Computer Menu on page 21. 
Auto Image Press  (Enter) / ► to automatically adjustment for phase, tracking, size and position. 
Advanced Press  (Enter) / ► to enter the Advanced menu. See Advanced Feature on page 
22. 
Color Manager Press  (Enter) / ► to enter the color manager menu. See page 24 for more 
information on Color Manager    
						

							– 21 – 
Computer Menu 
Press the MENU button to open the OSD menu. Press ◄► to move to the Image menu. Press ▲▼ 
to move to the Computer menu and then press Enter or ►. Press ▲▼ to move up and down in the 
Computer menu. 
 
ITEM DESCRIPTION 
Horizontal Position Press the cursor ◄► button to enter and adjust the display position to left or right.  
Vertical Position Press the cursor ◄► button to enter and adjust the display position to up or down.  
Frequency Press the cursor ◄► button to enter and adjust the A/D sampling clock. 
Tracking Press the cursor ◄► button to enter and adjust the A/D sampling dot.