Vivitek D5180hd Projector User Manual

DLP Projector—User’s Manual 
Installing the New Lens 
1.  Align the notches and correctly posi-
tion the electrical contact pad as 
shown in the picture. 
Note: 
Pin of IRIS should be in the direction 
as shown in the picture. 
2.  Rotate the lens clockwise until you 
feel it click into place. 
 
— 12 —  

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Starting and Shutting  down the Projector 
1.  Remove the lens cap. 
2.  Securely connect the power cord 
and signal cable. When connected, 
the power led will turn red. 
 
3.  Turn on the lamp by pressing 
“
” button on the rear of the 
projector or “
” on the remote 
control. 
The PWR LED will now flash 
red  
The startup screen will display in 
approximately 30 seconds. The first 
time you use the projector, you can 
select your preferred language from...

DLP Projector—User’s Manual 
4.  If more than one input device is con-
nected, press the SOURCE button 
to scroll among devices. 
(Component is supported through 
the RGB to COMPONENT 
ADAPTER.) 
 •  DVI: DVI 
•  
HDMI: HDMI 
•  
VGA1/ VGA2: Analog RGB 
•  
DP: DISPLAYPORT input 
•  
Component Video: DVD input YCbCr / YPbPr, 
or HDTV input YPbPr via HD15 connector
 
•  
S-Video: Super video (Y/C separated) 
•  
Composite Video: Traditional composite video
5.  When the “Power Off? /Press 
Power  again”...

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
•   The projector table or stand should be level and sturdy. 
•   Position the projector so that it is perpendicular to the screen. 
•   Remove the Back Foot Holder on the rear adjuster foot before adjusting the projection  
angle. 
•   Ensure the cables are in a safe location. You could trip over them.  
 
1.  To raise the level of the projector, 
twist the adjusters...

DLP Projector—User’s Manual 
Adjusting Projected Image Position Using Shift 
 
The Shift feature provides a lens shift function that can be used to adjust the position of the projected 
image either horizontally or vertica lly within the range detailed below. 
Shift is a unique system that provid es lens shift while maintaining a much higher ANSI contrast ratio 
than traditional lens shift systems. 
Adjusting the vertical image position 
The vertical image height can be  adjusted between 120% and -40% of...

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Adjusting the horizontal image position 
With the lens in the center posit ion the horizontal image position can be adjusted to the left or right by 
up to a maximum of 10% of the half image width.  Note that the maximum horizontal image height ad-
justment can be limited by the vertical image position. For example it  is not possible to achieve the 
maximum horizontal image position if  the vertical image position is at maximum. Please consult the 
Shift...

DLP Projector—User’s Manual 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom  
control (on the projector 
only) to resize the pro-
jected image and 
screen size. 
 
2.  Use the Image-focus  
control (on the projector 
only) to sharpen the 
projected image. 
 
3.  Use the KEYSTONE  
buttons (on the projec-
tor or the remote 
control) to correct im-
age-trapezoid (wider 
top or bottom)  
effect. 
 
Remote control and OSD panel 
4.  The keystone control  
appears on the display. 
 
—  18 —  

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Adjusting the Volume 
1.  Press the  Volume +/- . 
buttons on the remote 
control.  
The volume control  
appears on the display. 
2.  Press the  or   but-
tons on the keypad to 
adjust Volume +/- . 
 
 
3.  Press the MUTE button 
to turn off the volume 
(This feature is avail-
able only on the 
remote). 
 
 
–  19  –  

DLP Projector—User’s Manual 
— 20 — 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you ma ke image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control curs or buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illu stration shows the corresponding buttons on the 
projector. 
13
16
5
2
7
2
4
1
1
3
4
5
6
7
 
 
1.  To enter the OSD, press the  MENU but-
ton.  
2....

 P
P
P r
r
r e
e
e f
f
f a
a
a c
c
c e
e
e  
 
 
Setting the OSD Language 
Set the OSD language to your pr eference before continuing. 
1. Press the MENU button. Press the cursor  ▲▼ button to navigate to  Basic Setup. 
 
2.  Press the cursor ▲▼ button until  Language is highlighted.  
 
3.  Press the cursor  ▲▼ button until the language you want is highlighted.  
4. Press the  MENU button twice to close the OSD.   
– 21  –