Vivitek D330wx User Manual

							
DLP Projector – User’s Manual 
Setting an Access Password (Security Lock) 
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. 
When enabled, the password must be entered after you power on the projector. (See 
Navigating the 
OSD
 on page 18 and  on page 19 for help on using OSD menus.) Setting the OSD Language
Important: 
Keep the password in a safe place.  Without the password, you will not be able to use the projector. 
If you lose the password, contact your reselle r for information on clearing the password. 
 
1.  Press the Menu button to open the OSD 
menu. 
2.  Press the cursor  ◄► button to move to 
the  Installation I  menu, press the cursor 
▲▼  button to select  Advanced. 
 
3.  Press the cursor  ▲▼ button to select  
Security Lock . 
4.  Press the cursor  ◄► button to enable or 
disable security lock function. 
A password dialog box automatically  
appears. 
–  13  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector—User’s Manual 
5.  You can use the cursor buttons ▲▼◄► 
either on keypad or IR remote control for 
password entry. You can use any 
combination including the same arrow five 
times, but not less than five. 
 
Press the cursor buttons in any order to set 
the password. Push the  Menu button to 
exit the  dialog box. 
 
6.  The password confirm menu appears when 
user presses the power-on key in case the 
Security Lock  is enabled.  
Enter the password in the order you set it 
at step 5. In case you forget the password, 
please contact the service center.  
Service center will validate the owner and 
help reset the password.  
 
– 14 –  
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
– 15  – 
Adjusting the Projector Level 
Take note of the following when setting up the projector: 
•  The projector table or stand should be level and sturdy. 
•   Position the projector so that it is perpendicular to the screen. 
•   Ensure the cables are in a safe location. You could trip over them.  
 
 
 
1.   To raise the level of the projector, lift the projector  [A] and press the height-adjuster 
button  [B].  
The height adjuster drops down  [C].  
2.  To lower the level of the projector, press  the height-adjuster button and push down 
on the top of the projector. 
3.   To adjust the angle of the pi cture, turn the tilt-adjuster [D] right or left until the 
desired angle has been achieved. 
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector—User’s Manual 
Adjusting the Zoom, Focus and Keystone 
1.  Use the Image-zoom   
control (on the projector 
only) to resize the pro-
jected image and screen 
size 
B. 
2.  Use the  Image-focus   
control (on the projector 
only) to sharpen the pro-
jected image 
 A. 
3.  Use the  Quick Menu  but-
ton on the projector or 
Keystone  on the remote 
control to correct image-
trapezoid (wider top or 
bottom) effect. 
Remote control and OSD panel
 
4.  The keystone control  
appears on the display. 
 
– 16 –  
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
Adjusting the Volume 
1.  Press the Volume +/-   
buttons on the remote 
control.  
The volume control  
appears on the display. 
 
 
2.  Press the  Down Cursor  
button on the keypad to 
adjust Volume +/- . 
 
 
3.  Press the  Mute button to 
turn off the volume (This 
feature is available only 
on the remote). 
 
 
–  17  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector—User’s Manual 
– 18 – 
ON-SCREEN DISPLAY (OSD) MENU SETTINGS 
OSD Menu Controls 
The projector has an OSD that lets you ma ke image adjustments and change various settings.  
Navigating the OSD 
You can use the remote control curs or buttons or the buttons on the top of the projector to navigate 
and make changes to the OSD. The following illust ration shows the corresponding buttons on the re-
mote control and on the projector. 
 
 
 
 
1.  To enter the OSD, press the  Menu button.  
2.  There are five menus. Press the cursor  ◄► button to 
move through the menus.  
3. Press the cursor  ▲▼ button 
to move up and down in a 
menu.  
4. Press  ◄► to change values 
for settings. 
5. Press  Menu to close the 
OSD or leave a submenu. 
Note: 
Depending on the video source, not all items in  the OSD are available. For example, the Horizon-
tal/Vertical Position  items in the Computer menu can only be modified when connected to a PC. 
Items that are not available cannot  be accessed and are grayed out.  
 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
Setting the OSD Language 
Set the OSD language to your preference before continuing. 
1.  Press the  Menu button. Press the cursor  ◄► button to navigate to Installation I. 
 
2.  Press the cursor  ▲▼ button until  Language is highlighted.  
 
3.  Press the cursor  ◄► button until the language you want is highlighted.  
4.  Press the  Menu button twice to close the OSD.   
– 19  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector—User’s Manual 
OSD Menu Overview 
Use the following illustration to quickly find a setting or determine the range for a setting. 
 
 
– 20 – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector – User’s Manual 
OSD Sub-Menu Overview 
 
– 21  – 
Downloaded From projector-manual.com Vivitek Manuals 
						

							
DLP Projector—User’s Manual 
Image Menu  
Press the Menu button to open the OSD menu. Press the cursor  ◄► button to move to the  Image 
Menu. Press the cursor  ▲▼ button to move up and down in the  Image menu. Press  ◄► to change 
values for settings. 
 
ITEM DESCRIPTION 
Display Mode Press the cursor  ◄► button to set the Display Mode.  
Brilliant Color Press the cursor  ◄► button to adjust the Brilliant Color value. 
Brightness Press the cursor ◄►  button to adjust the display brightness. 
Contrast Press the cursor ◄► button to adjust the display contrast. 
Sharpness Press the cursor  ◄► button to adjust the display sharpness level. 
Gamma Press the cursor  ◄► button to adjust the gamma correction of the display.  
– 22 –  
Advanced Press  (Enter) /  ► to enter the Advanced menu. See  Advanced Feature on page 23. 
 (Enter) / ► to reset all settings to default values. Press Reset 
 
Downloaded From projector-manual.com Vivitek Manuals