Vivitek D330wx User Manual

DLP Projector – User’s Manual 
– 3  – 
Top view—On-screen Display (OSD) buttons and LEDs 
 
ITEM LABEL DESCRIPTION SEE 
PAGE: 
1.   (Power) 
Turns the projector On or Off 
2.  ▲
 (Up cursor)  Navigates and changes settings in the OSD 18 
Green   Power On  
Off   Power Off (AC Off) 3.  Power LED 
Flashing Error code 
On  System over temperature 4.  Over Temp LED Off Normal State 
Orange  Lamp is ready to be powered-on. 
5.  Ready LED 
Flashing Lamp not ready (Warm-up/shutting down/cooling)  
(see 
LED...

DLP Projector—User’s Manual 
Rear view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
111.  AC IN Connect the POWER CABLE 
Connect the USB CABLE from a computer  (Service 
Only) 2.  USB (Service Only) 
3.  AUDIO Connect the AUDIO CAB LE from the input device  
4.  S-VIDEO Connect the S-VIDEO CABLE from a video device 
– 4 – 
5.  VIDEO  Connect the VIDEO CABLE from a video device  
10
6.  VGA Connect the RGB cable (supplied) from a computer 
Connect the HDMITM digital video CABLE from a video 
device 7.  HDMITM...

DLP Projector – User’s Manual 
– 5  – 
Bottom view 
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Lamp cover  Remove when changing the lamp.  X36X 
2.  Height adjustor button  Push to release adjustor. 
3.  Height adjustor  Adjuster drops down  when adjuster button is pushed. 
X15 
4.  Lens cap hook   To fasten the lens cap cover. 
5.  Tilt adjustor   Rotate adjuster lever to adjust angle position.  X15 
6.  Ceiling support holes  Contact your dealer for information on mounting the projector on a ceiling....

DLP Projector—User’s Manual 
Remote Control Parts 
 
Important: 
1. Avoid using the projector with bright fluoresc ent lighting turned on. Certain high-frequency fluo-
rescent lights can disrupt remote control operation. 
 
2. Be sure nothing obstructs the path between the re mote control and the projector. If the path be-
tween the remote control and the projector is obstructed, you can bounce the signal off certain 
reflective surfaces such as projector screens. 
 
3. The buttons and keys on the...

DLP Projector – User’s Manual 
– 7 –  
 
ITEM LABEL DESCRIPTION SEE PAGE: 
1.  Up cursor Navigates and changes settings in the OSD   
2.  Enter Changes settings in the OSD 
18
3.  Power Turns the projector On or Off 11
4.  Right cursor Navigates and changes settings in the OSD 18
5.  Volume + Increase volume 
6.  Volume - Decrease volume 
17
7.  Mute Mutes the built-in speaker 
8.  Freeze Freeze/unfreezes the on-screen picture 
9.  Source Detects the input device 
10.  Auto Auto adjustment for...

DLP Projector—User’s Manual 
Remote Control Operating Range 
The remote control uses infrared transmission to control the projector. It is not necessary to point the 
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or 
the rear of the projector, the re mote will function well within a radi us of about 7 meters (23 feet) and 
15 degrees above or below the projector level. If the pr ojector does not respond to the remote control, 
move a little closer....

DLP Projector – User’s Manual 
– 9 –  
SETUP AND OPERATION 
Inserting the Remote  Control Batteries  
1.  Remove the battery compartment cover 
by sliding the cover in the direction of 
the arrow. (A) Pull out the cover. (B) 
 
2.  Insert the battery with the positive side 
facing up. 
 
3.  Replace the cover. 
 
 
Caution: 
1. Only use a 3V lithium battery (CR2025). 
 
2. Dispose of used batteries accordi ng to local ordinance regulations.  
 
3. Remove the battery when not using  the projector for...

DLP Projector—User’s Manual 
– 10 – 
Connecting Input Devices 
A PC or notebook computer and video devices can be connected to the projector at the same time. Video 
devices include DVD, VCD, and VHS players, as we ll as movie camcorders and digital still cameras. 
Check the user manual of the connecting device to  confirm it has the appropriate output connector.  
 
ITEM LABEL DESCRIPTION 
A 
USB  (Service Only)  Connect the USB CABLE from a computer. (Service Only) 
B 
AUDIO Connect the AUDIO CABLE...

DLP Projector – User’s Manual 
Starting and Shutting down the Projector 
 
1.  Connect the power cord to the projector. 
Connect the other end to a wall outlet. 
The 
 Power  and Ready  LEDs on the 
projector light. 
2.  Turn on the connected devices. 
 
3.  Ensure the  Ready LED displays a solid 
orange and not a flashing orange. Then 
press the 
  Power  button to turn on 
the projector.  
 
The projector splash screen displays and 
connected devices are detected. 
 
See 
Setting an Access Password...

DLP Projector—User’s Manual 
5.  When the “Power Off? /Press Power 
again” message appears, press the 
Power button. The projector turns off. 
 
Caution: 
1. Be sure to remove the lens  cap before starting projector.  
2. Do not unplug the power cord until the  POWER LED stops flashing–indica ting the projector has 
cooled down. 
 
 
 
– 12 – 
Downloaded From projector-manual.com Vivitek Manuals