Vivitar Vivicam 3305 Users Manual

							Downloaded from www.Manualslib.com manuals search engine 20
 If there is no image stored in the memory a “No Picture” message pops up. To exit this message,
switch to any other camera mode.
 You can review the recorded images on the LCD Monitor or on a TV.
How to set the focus?
Before taking a picture, you may need to set the focus. The camera provides 2 different type for your
selection:
Simply switch the Focus knob to select one.
Mode                      Effective Range               Description
For a normal/long distance shot
(60CM~    )
For a macro shot(30-60CM) Icon
Portrait/Telephoto
Icon
Close-up
8  
						

							Downloaded from www.Manualslib.com manuals search engine 21
How to set the image resolution & quality ?
This camera provides 6 different image resolution & quality combination settings:
1280x960 pixels resolution with Normal (   ), Fine(       ), Super Fine(          )quality.
640x480 pixels resolution with Normal (   ), Fine(       ), Super Fine(          )quality.
To change the resolution & quality setting, perform the following:
1. Power on the camera.
2. Set the operating mode to RECORD      .
3. Press the Resolution & Quality button        . To toggle the selection.
The setting is conserved even if the camera power is off.
Resolution Indicator
In RECORD mode: Shows the captured image resolution setting.
In PLAY mode: Shows the currently displayed image resolution setting.
Image Quality Indicator
In RECORD mode: Shows the captured image quality setting.
In PLAY mode: Shows the currently displayed image quality setting.  
						

							Downloaded from www.Manualslib.com manuals search engine 22
The setting is conserved even if the camera power is off.
How to set the Flash?
The Flash Mode can only be set under RECORD mode.  There are 4 modes available: Auto, Red-Eye,
Fill-In and Off.  The default setting is OFF.  To change the setting, press the Flash Mode button a
number of times until the desired one is selected.
  1280x960
  1280x960
  1280x960
  640x480
  640x480
  640x480  20:1
  12:1
  8:1
  16:1
  8:1
  4:1
  Resolution          Quality                Compression Ratio
Mode                  Description
     Flash is enabled automatically when light level is less than LV 10.0
     Auto Mode with Pre-Flash to reduce red eye effect
     Flash is always enabled
     Flash is always disabled Auto
Red-Eye
Fill-In
Off  
						

							Downloaded from www.Manualslib.com manuals search engine 23
Advanced Operation
How to adjust the EV compensation?
To adjust the EV compensation, perform the following:
1. Set the operating mode to RECORD     .
2. Press the Menu button.  The Record menu appears.
3. Select the EV COMPENSATION item.
4. Select the desired exposure value.
* The effective range is from -1.8 to +1.8 in steps of 0.3 EV.
This setting is reset to AUTO when the camera power is off.
How to adjust the White Balance?
To adjust the White Balance, perform the following:
1. Set the operating mode to RECORD     .
2. Press the Menu button.  The Record menu appears.
3. Select the WHITE BALANCE item.
4. Select the desired white balance setting.
This setting is reset to AUTO when the camera power is off.  
						

							Downloaded from www.Manualslib.com manuals search engine 24
How to set the OSD (On-Screen Display) language?
To set the OSD language, perform the following:
1. Set the operating mode to SETUP.
2. The Setup menu appears.
3. Select the LANGUAGE item.
4. Select the desired language setting.
The setting is conserved even if the camera power is off.
How to set the Self-Timer?
The self-timer can only be set under RECORD      mode.
To use the Self-Timer function, perform the following:
1. Press the Self-Timer button      to activate the Self-timer.
2. Press the Shutter button.
3. After 10 seconds, an image is captured and the timer will turn itself off.
The Self-Timer is designed to count down for 10 seconds.  In the first 7 seconds, the indicator blinks
at a rate relatively slow and then blinks rapidly for the last 3 seconds.
How to format the CF (Compact Flash  ) card?
To format the CF card, perform the following:
1. Set the operating mode to SETUP.
2. Select the FORMAT MEDIA item.
3. Select YES to re-format the CF card (default = NO).
TM  
						

							Downloaded from www.Manualslib.com manuals search engine 25
Operating Modes and Menus
RECORD Mode
Set the operating mode to RECORD      for image capturing.
Record Menu
Press the Menu button      in RECORD      mode, the Record menu appears.
The menu contains the following items:
LCD BRIGHTNESS:
Changes the brightness setting (-5 ~ +5, Interval = 1) of the LCD display.
Press the OK button to select this item.  The cursor skips to the data field as the OK button being
pressed.  Use the arrow buttons (           ) to increase/decrease the LCD brightness.  Press the OK
button again to make the change.  The cursor returns to the RECORD menu automatically when the
change is made.
The setting is conserved even if the camera power is off.
QUICKVIEW :
Toggles On/Off the QuickView function.
Select the item by the arrow buttons (           ) and then press the OK button to confirm.  The cursor
skips to the data field as the OK button being pressed.  Use the arrow buttons (           ) to select the/
/
/  
						

							Downloaded from www.Manualslib.com manuals search engine 26
desired setting.  The cursor returns to the Record menu automatically when the change is made.
The setting is conserved even if the camera power is off.
WHITE BALANCE:
Select either one of the 5 (Auto, Daylight, Shade, Fluorescent, Tungsten) manual white balance settings.
The auto white balance is recommended for most cases.  For certain critical circumstances, if the
result did not come out as expected, you may manually change to another white balance type accord-
ing to the ambient lighting condition.
Select the item by the arrow buttons (           ) and then press the OK button to confirm.  The cursor
skips to the data field as the OK button being pressed.  Use the arrow buttons (           ) to select the
desired white balance type.  Press the OK button again to make the change.  The cursor returns to the
RECORD menu automatically when the change is made.
This setting is reset to AUTO when the camera power is off.
Reference:
The approximate color temperature of the 4 above white balance settings (except Auto White Balance)
will be Daylight = 5500K, Shade = 6000K, Flourescent = 5800K and Tungsten = 2850K.
EV COMPENSATION:
Adjusts the exposure compensation over a range of -1.8 to +1.8 EV in steps of 0.3 EV.
Select the item by the arrow buttons (           ) and then press the OK button to confirm.  The cursor
skips to the data field as the OK button being pressed.  Use the arrow buttons (           ) to increase/
decrease the EV compensate value (-1.8 ~ +1.8).  Press the OK button again to make the change.  The/
/
/
/  
						

							Downloaded from www.Manualslib.com manuals search engine 27
cursor returns to the Record menu automatically when the change is made.
This setting is reset to AUTO when the camera power is off.
Play Mode
In Play mode, users can review the recorded images on the LCD Monitor or on a TV.  Set the operating
mode to PLAY for image review.
Play Menu
Press the Menu button in PLAY mode, the Play menu appears.
The menu contains the following items:
LCD BRIGHTNESS:
Changes the brightness setting (-5 ~ +5, Interval = 1) of the LCD Monitor.
Press the OK button to select this item.  The cursor skips to the data field as the OK button being
pressed.  Use the arrow buttons (           ) to increase/decrease the LCD brightness.  Press the OK
button again to make the change.  The cursor returns to the Record menu automatically when the
change is made.
The setting is conserved even if the camera power is off.
/  
						

							Downloaded from www.Manualslib.com manuals search engine 28
SLIDE SHOW:
Displays the recorded images sequentially, with a user-defined delay between images.
Select the item by the arrow buttons (           ) and then press the OK button to confirm.  The cursor
skips to the data field as the OK button being pressed.  Use the arrow buttons (           ) to increase/
decrease the delay between 2 to10 seconds with interval 2 .  Press the OK button again to make the
change.  The slide show starts.
Press the Display/Menu/OK/ arrow buttons (           ) buttons or switch the Operating Mode knob while
a slide show is playing to interrupt the display and returns to the PLAY mode.
COPY TO CF CARD:(Optional)
Copy the recorded images to the external CF card.
Select the item by the arrow buttons (           ) and then press the OK button to confirm.  The cursor
skips to the data field as the OK button being pressed. Use the arrow buttons(          )to toggle the YES
or NO option. Then press OK button to confirm./
/
/
/
/  
						

							Downloaded from www.Manualslib.com manuals search engine 29
Setup Mode
In SETUP mode, users can customize their own preferences according to the actual requirements.
Setup Menu
Switch the Operating Mode knob to SETUP, the Setup menu appears.  The menu contains the follow-
ing items:
DATE/TIME:
Displays the date and time information.
When the camera is used for the 1st time or the batteries are replaced, you may need to have the
correct date/time set.
Press the OK button to select DATE/TIME.  The cursor skips to the data field and the first item (Month)
in this field is selected.  Use the arrow buttons (          ) to change the number or press the OK button
to proceed to the next item.  When the last item is selected/changed, press OK button to return to the
Setup menu.
LANGUAGE:
Sets the OSD menu language.
There are 7 languages available for your selection.  They are English, French, German, Spanish,
Japanese, Portuguese and Traditional Chinese.
Select the item by the arrow buttons (          ) and then press the OK button to confirm.  The cursor skips
to the data field as the OK button being pressed.  Use the arrow buttons (           ) to select the desired
/
/
/