Vivitar Projector H9090 User Manual
Have a look at the manual Vivitar Projector H9090 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 208 Vivitar manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 36
36
using the socket’s switch instead of the remote. If you do not need this function, please\
set
it to Off.
Rear Projection: This control reverses all images and menus, and is necessary when the
projector is used in rear-projection applications. The default is Off. Refer to Page 15 ---
Modes of installation
Celling Mode : This control flips the image so the projector can be used in ceiling mounted
installations. The default setting, Auto, automatically determines the orientation using an...](http://img.usermanuals.tech/thumb/5165/100422/w64_projector_manual_9190_d-35.png "Page 36
36
using the socket’s switch instead of the remote. If you do not need this function, please\
set
it to Off.
Rear Projection: This control reverses all images and menus, and is necessary when the
projector is used in rear-projection applications. The default is Off. Refer to Page 15 ---
Modes of installation
Celling Mode : This control flips the image so the projector can be used in ceiling mounted
installations. The default setting, Auto, automatically determines the orientation using an...")
![Page 37
37
output also stops when the projector is turned off.
Auto Source: Default setting is “Off”. By enabling this function, the projector will
automatically determine the source of input every time it is turned on s\
o that the user will
not have to make the selection on the OSD Menu. Setting the function off will require the
user to specify source of image input on the OSD Menu in order for the p\
rojector to display
the intended image.
OSD Introduction – LANGUAGE
Choose the OSD display language that...](http://img.usermanuals.tech/thumb/5165/100422/w64_projector_manual_9190_d-36.png "Page 37
37
output also stops when the projector is turned off.
Auto Source: Default setting is “Off”. By enabling this function, the projector will
automatically determine the source of input every time it is turned on s\
o that the user will
not have to make the selection on the OSD Menu. Setting the function off will require the
user to specify source of image input on the OSD Menu in order for the p\
rojector to display
the intended image.
OSD Introduction – LANGUAGE
Choose the OSD display language that...")
![Page 39
39
Maintenance and Troubleshooting
Table below provides some general guidelines for troubleshooting problems\
you may
encounter with the H9090. If the suggested solutions fail to resolve the\
problem or if you
encounter an issue not described here, please contact Vivitek Technical.
Troubleshooting Chart
LED lights solid red.
Fans are not working prop erly or
power-on self-tes t \fas failed (Note\b.
Power o t\fe H9090 and allow\f it
to cool down. Turn \ft\fe projector
back on. If...](http://img.usermanuals.tech/thumb/5165/100422/w64_projector_manual_9190_d-38.png "Page 39
39
Maintenance and Troubleshooting
Table below provides some general guidelines for troubleshooting problems\
you may
encounter with the H9090. If the suggested solutions fail to resolve the\
problem or if you
encounter an issue not described here, please contact Vivitek Technical.
Troubleshooting Chart
LED lights solid red.
Fans are not working prop erly or
power-on self-tes t \fas failed (Note\b.
Power o t\fe H9090 and allow\f it
to cool down. Turn \ft\fe projector
back on. If...")
![Page 40
40
Serial Communications
RS-232Connection and Port Configuration
To interface the H9090 with a home theater automation/control system or a\
PC running
terminal emulation software:
1. Connect it to your control system or PC.
2. Start a terminal session on your PC using a terminal-emulation program, \
such as
HyperTerminal.
3. Configure the RS-232 controller or PC serial port as follows: 38400 bps, no parity , 8
data bits, 1 stop bit and no flow control.
4. Type ky or op followed by a...](http://img.usermanuals.tech/thumb/5165/100422/w64_projector_manual_9190_d-39.png "Page 40
40
Serial Communications
RS-232Connection and Port Configuration
To interface the H9090 with a home theater automation/control system or a\
PC running
terminal emulation software:
1. Connect it to your control system or PC.
2. Start a terminal session on your PC using a terminal-emulation program, \
such as
HyperTerminal.
3. Configure the RS-232 controller or PC serial port as follows: 38400 bps, no parity , 8
data bits, 1 stop bit and no flow control.
4. Type ky or op followed by a...")
![Page 42
42
Operations Commands: Operations commands allow more flexible and direct control
of the projector. The syntafor operations commands is as follows:
op [CR]
(Precede and with a space.)
The command type can be one of 5 functions:
Operation Control Commands
Function Command Action on unit
Set = Makes the unit take that value.
Get ?asks what the current value is.
Increment +Add 1 to the current value.
Decrement -Subtracts 1 from the current value.
Execute Performs and action as a reset.
• Below are...](http://img.usermanuals.tech/thumb/5165/100422/w64_projector_manual_9190_d-41.png "Page 42
42
Operations Commands: Operations commands allow more flexible and direct control
of the projector. The syntafor operations commands is as follows:
op [CR]
(Precede and with a space.)
The command type can be one of 5 functions:
Operation Control Commands
Function Command Action on unit
Set = Makes the unit take that value.
Get ?asks what the current value is.
Increment +Add 1 to the current value.
Decrement -Subtracts 1 from the current value.
Execute Performs and action as a reset.
• Below are...")
![Page 43
43
Serial Operation Commands (continued)
The last two commands show what happens when a control is grayed out. In\
this case, the
sharpness mode was set to advanced (value = 1) and then the simple sha\
rpness slider
was attempted to be adjusted and queried. The response was “NA” or not available.
Serial Command OperandValue Notes
aspect = ?0 = 16:9
1 = Letterbox
2 = 4:3
3 = Theaterscope
4 = Native
recall.mem = ?0 = Preset A
1 = Preset B
2 = Preset C
3 = Preset D
4 = Default
save.mem =0 =...](http://img.usermanuals.tech/thumb/5165/100422/w64_projector_manual_9190_d-42.png "Page 43
43
Serial Operation Commands (continued)
The last two commands show what happens when a control is grayed out. In\
this case, the
sharpness mode was set to advanced (value = 1) and then the simple sha\
rpness slider
was attempted to be adjusted and queried. The response was “NA” or not available.
Serial Command OperandValue Notes
aspect = ?0 = 16:9
1 = Letterbox
2 = 4:3
3 = Theaterscope
4 = Native
recall.mem = ?0 = Preset A
1 = Preset B
2 = Preset C
3 = Preset D
4 = Default
save.mem =0 =...")
41 Serial Command Key Names RS232 KeynameRemote ButtonDescription power.on lTurn power on. power.off Turn power off. menu MENUBring up or cancel menu display. enter ENTERKeypad enter. down Keypad down arrow. up Keypad up arrow. left Keypad left arrow. righ Keypad right arrow. bright Bring up or cancel brightness slider contrast Bring up or cancel contrast slider sharp SHARPBring up or cancel sharpness slider nr NRBring up or cancel noise reduction slider gam.sw GAMMASwitch to the next gamma src.1 1Switch the active source to source 1. src.2 2Switch the active source to source 2. src.3 3Switch the active source to source 3. src.4 4Switch the active source to source 4. src.5 5Switch the active source to source 5. osc.sw O-SCANSwitch to the next Overscan mode mem.1 ARecall user memory associated with the Preset A key mem.2 BRecall user memory associated with the Preset B key mem.3 CRecall user memory associated with the Preset C key asp.sw ASPECT RATIOSwitch to the next aspect ratio. bcolor.sw BRI-CToggles between BrilliantColor On and BrilliantColor Off ctemp.sw C-TEMPChange to next Color Temperature pattern.sw TESTActivate Test Patterns H9090 Home Theater Projector - User Manual
42
Operations Commands: Operations commands allow more flexible and direct control
of the projector. The syntafor operations commands is as follows:
op [CR]
(Precede and with a space.)
The command type can be one of 5 functions:
Operation Control Commands
Function Command Action on unit
Set = Makes the unit take that value.
Get ?asks what the current value is.
Increment +Add 1 to the current value.
Decrement -Subtracts 1 from the current value.
Execute Performs and action as a reset.
• Below are lists the valid operations commands. For all but Execute funct\
ions, the
response from the projector is the command and “= ” where is the
current value or “NA” if the value is not available. For Execute f\
unctions the response
is the same command. All responses are in UPPERCASE.
Some operations command samples:
Input Response
op bright ? [CR] OP BRIGHT = 100
op bright + [CR] OP BRIGHT = 101
op bright = 127 [CR] OP BRIGHT = 127
op bright - [CR] OP BRIGHT = 126
op sharp. simple = 50 [CR] Unknown Command
op sharp.simple ? [CR] Unknown Command
H9090 Home Theater Projector - User Manual
43 Serial Operation Commands (continued) The last two commands show what happens when a control is grayed out. In\ this case, the sharpness mode was set to advanced (value = 1) and then the simple sha\ rpness slider was attempted to be adjusted and queried. The response was “NA” or not available. Serial Command OperandValue Notes aspect = ?0 = 16:9 1 = Letterbox 2 = 4:3 3 = Theaterscope 4 = Native recall.mem = ?0 = Preset A 1 = Preset B 2 = Preset C 3 = Preset D 4 = Default save.mem =0 = Preset A 1 = Preset B 2 = Preset C 3 = Preset D bright = ? + -0 - 200 contrast = ? + -0 - 200 saturat = ? + -0 - 200 tint = ? + -0 - 200 sharp = ? + -0 - 200 nr = ? + -0 - 200 zoom = ?0 = Off 1 = Crop 2 = Zoom input.sel = ?0 = HDMI 1 1 = HDMI 2 2 = RGB 3 = YPrPb 1 4 = YPrPb 2 5 = S-Video 6 = Video auto.img (execute) color.space = ?0 = Auto 1 = REC709 2 = REC601 3 = RGB-PC 4 = RGB-Video H9090 Home Theater Projector - User Manual
44 video.stand= ?0 = Auto 1 = NTSC 2 = PAL 3 = SECAM gamma = ?0 = CRT 1 = Film 2 = Video 3 = Bright 4 = Graphics color.temp = ?0 = 5500K 1 = 6500K 2 = 7500K 3 = 9300K color.gamut = ?0 = Auto 1 = REC709 2 = SMPTE C 3 = EBU 4 = Native bcolor = ?0 = Off 1 = On dblack = ?0 = off 1 = 4x 2 = 8x 3 = max. red.offset = ? + -0-200 green.offset = ? + -0-200 blue.offset = ? + -0-200 red.gain = ? + -0-200 green.gain = ? + -0-200 blue.gain = ? + -0-200 v.pos = ? + -0-200 h.pos = ? + -0-200 h.phase = ? + -0-200 tracking = ? + -0-200 sync.level = ? + -0-200 osd.menupos = ?0 = Top left 1 = Top right 2 = Bottom left 3 = Bottom right 4 = Center H9090 Home Theater Projector - User Manual
45 blank.screen= ?0 = Black 1 = Blue 2 = White 3 = Logo auto.poweroff = ?0 = Off 1 = On auto.poweron = ?0 = Off 1 = On rear.proj = ?0 = Off 1 = On ceil.mode = ?0 = Off 1 = On 2 = Auto startup.logo = ?0 = Off 1 = On 1.key 2.key 3.key 4.key 5.key = ? 0 = HDMI 1 1 = HDMI 2 2 = RGB 3 = YPrPb 1 4 = YPrPb 2 5 = S-video 6 = Video auto.source = ?0 = Off 1 = On model ? ser.number ? soft.version ? act.source ?0 = HDMI 1 1 = HDMI 2 2 = RGB 3 = YPrPb 1 4 = YPrPb 2 5 = S-video 6 = Video h.refresh ? kHz v.refresh ? Hz pixel.clock ? MHz signal ? total.hours ? environment ? Temperatures H9090 Home Theater Projector - User Manual
46 fact.reset(execute) blue.only =0 = Off 1 = On pattern =0 = White 1 = Black 2 = Red 3 = Green 4 = Blue 5 = Cyan 6 = Magenta 7 = Yellow 8 = ANSI Checkerboard 9 = Horizontal Gray Ramp 10 = Focus Grid 11 = Off altitude = ?0 = low 1 = high hsg.r.hue = ? + -0-200 hsg.g.hue = ? + -0-200 hsg.b.hue = ? + -0-200 hsg.c.hue = ? + -0-200 hsg.m.hue = ? + -0-200 hsg.y.hue = ? + -0-200 hsg.r.sat = ? + -0-200 hsg.g.sat = ? + -0-200 hsg.b.sat = ? + -0-200 hsg.c.sat = ? + -0-200 hsg.m.sat = ? + -0-200 hsg.y.sat = ? + -0-200 hsg.r.gain = ? + -0-200 hsg.g.gain = ? + -0-200 hsg.b.gain = ? + -0-200 hsg.c.gain = ? + -0-200 hsg.m.gain = ? + -0-200 hsg.y.gain = ? + -0-200 hsg.wr.gain = ? + -0-200 hsg.wg.gain = ? + -0-200 hsg.wb.gain = ? + -0-200 status ?0 = standby 1 = warm up 2 = imaging 3 = cooling 4 = error FVER ? H9090 Home Theater Projector - User Manual
47 trig.1 trig.2= ? 0 = Screen 1 = 16:9 2 = Letterbox 3 = 4:3 4 = 4:3 Narrow 5 = RS232 6 = On 7 = Off IF you want select 6 or 7,please select 5 at first language = ?0 = English 1 = French 2 = Spanish H9090 Home Theater Projector - User Manual
48 RS-232 Error Codes If an errcode ? command returns one of the following values, you have en\ countered a likely system error requiring the attention of a qualified service technician. Try resetting the projector by powering it off, allowing it to cool and powering it on again. The specific code number identifies the source of the error detected, and is particularly useful in cases where the projector is far away. For example, the code “7” means that Fan 1 has failed. Error Code Description 0 Inlet NTC thermal sensor is over temperatuer. 1 Outlet NTC thermal sensor is over temperatuer. 2 Red LED thermal sensor is over temperatuer. 3 Green LED thermal sensor is over temperatuer. 4 Blue LED thermal sensor is over temperatuer. 6 Fans error when system power on. 7 Fan1 locked 8 Fan2 locked 9 Fan3 locked 10 Fan4 locked 11 Fan5 locked 12 Fan6 locked 15 DDP3021 communication fail when system power on 16 Lamp ignited fail 3 times when system power on 17 Power reset when led-driver error. 19 PCF8575 external GPIO communication fail, it can crash system. 21 GENNUM SPI communication fail when system power on. 22 System hardware I2C communication fail, it can crash system. 23 System software I2C communication fail. 24 Check sum of EEPROM error. 25 Check sum of EDID error. 26 EEPROM version fail 27 Gennum reset 28 Successfully re-ignited when system power on H9090 Home Theater Projector - User Manual
49
Specifications
H9090 LED Specifications
Optics
TechnologyTI DLP 1080p (1920 x 1080) 0.95” DMD
Light Source LED (Red/Green/Blue) 135% NTSC color gamut
Projector Lens Standard Lens throw ratio: 1.85 to 2.4:1
Short Lens throw ratio: 1.56 to 1.86:1 (optional)
Long Lens throw ratio: 2.4 to 4.0:1 (optional)
Lens Shift • Vertical ± 60%
• Horizontal ± 15%
Image width range 8ft to 30ft
Electrical
I/O - Video Input • DB15 pin RGB
• 2 x HDMI
• Component 1 - RCA
• Component 2 - BNC
• Composite (RCA)
• S-Video
I/O - Power Input IEC-320-C14receptacle
Projector Control • Hard wired via RS-232
• IR Remote
• Keypad control method
Zoom/Focus/Offsets Manual lens shift, Manual zoom/focus
Projection Modes Front/ Rear/ Ceiling (Front/Rear)
Power • Input Voltage: 100 ~ 240V
• Power Consumption
• 110V: BrilliantColor ON 280W, BrilliantColor OFF 240W,
Standby
50 H9090 LED Specifications (continued) Reliability Operating Temperature• 7500 ft.~10000 ft. (2286m ~ 3048m): 50 ~ 95°F (10 ~ 35°C), Humidity: 0% ~ 85% • Under 7,500 ft. (2286m): 50 ~ 104°F (10 ~ 40°C), Humidity: 0% ~ 85% Storage -4 ~ 140°F (-20 ~ 60°C), Humidity: 5% ~ 90% Standard Accessories Power CordUS 110VAC Remote and Batteries For set up and use only HDMI Cable For set up and use only User Manual CD For set up and use only Warranty Card Allen Wrench For lens shift adjustment Note: Specifications are subject to change without notice H9090 Home Theater Projector - User Manual