Vivitar Dp 1200x Projector User Manual

EN-10
○○○○○○○○○○○
User’s Manual Projector
SETUP
This section tells you how to unpack and set up your projector and connect it to other
equipment. The projector must be connected to a computer or a video source such as
a video tape deck, camcorder, digital camera or laser disk player in order to make a
projection.
You may want to connect the projector to both your computer and a video source, or
set up the projector for one or more of the following:
   Connect the mouse cable to use the remote controller...

EN-11
○○○○○○○○○○○
. English .
User’s ManualProjector
Setting Up the Projector
1.Place the projector on a sturdy, level surface within five feet of the computer or video
   source.
   Caution:
       Do not hold the projector by the lens. This can damage the lens.
2.Place the projector the correct distance from the screen. The distance between the
   projector and   the screen determines the actual image size. Use the general
   guidelines below to determine the correct distance....

EN-12
○○○○○○○○○○○
User’s Manual Projector
Connecting to a Computer
The projector will always project at XGA (1024 x 768) resolution. (XGA is the native
resolution of the projector.) However, you can connect the projector to a computer
source capable of displaying VGA (640 x 480), SVGA (800 x 600), XGA or SXGA
(1280 x 1024) resolutions. The projector will resize VGA, SVGA, and SXGA inputs for
XGA projection. The types of computers supported by this projector include IBM,
Macintosh and Apple compatible...

EN-13
○○○○○○○○○○○
. English .
User’s ManualProjector
Connecting to a Video Source
You can connect the projector to almost any common video source - VHS player, DVD
player, camcorder, laser disc player or any other compatible video image source.
The projector can accept composite, component, or S-Video signals:
Composite video is characterized by a single-pin “RCA-type” video jack, usually
colored yellow.
Component video (YCbCr) is less common and features three “RCA-type” video
jacks, typically colored...

EN-14
○○○○○○○○○○○
User’s Manual Projector
Using the Projector
This section describes projector operations:
   Turning the projector and A/V equipment on and off
   Adjusting the projected image
   Projector controls
   Checking the projector status
Turning the Audio/Visual (A/V) Equipment On and
Off
Always turn on the projector and related A/V equipment in the following order.
1.Projector
2.Computer
3.Video source
4.Audio source
Turning the Projector On and Off
1.Connect the power cord to the projector....

EN-15
○○○○○○○○○○○
. English .
User’s ManualProjector
Focusing and Positioning the Screen Image
After an image appears on the screen, check to see if it is in focus and whether it fits
properly on the screen.
   To adjust the focus of the image, rotate the focus ring, which is the right one on the
   projector’s lens.
   To adjust the size of the image, rotate the left zoom ring. Zooming out to make the
   image larger or zooming in make it smaller on the screen.
Note:
Push the adjuster button to adjust...

EN-16
○○○○○○○○○○○
User’s Manual Projector
Operational Indicator (LED)
There are two LEDs on the top of the projector, the Power LED and the Lamp LED.
They provide valuable information about the projector.
LED TYPE           COLOR               STATUS            MEANING
Power LED          Green              Solid             The projector is powered and ready.
Power LED          Red              Solid             The projector system has some problems with its fan, so...

EN-17
○○○○○○○○○○○
. English .
User’s ManualProjector
2.Selecting the desired menu or sub-menu(to scroll through the menu choices):
   On the Projector Control Panel: press the 
c cc c
c or 
d dd d
d  button.
   On the Remote Controller: press the 
c cc c
c or 
d dd d
d button.
   Note:
      To scroll up: press the c button.
      To scroll down: press the d button.
3. Adjusting the value setting:
   On the Projector Control Panel: press the 
e ee e
e or 
f ff f
f button.
   On the Remote Controller:...

EN-18
○○○○○○○○○○○
User’s Manual Projector
Menu Options
The projector is equipped with three types of on-screen display(OSD) menus.
Each OSD menu interface you will see on the screen is depending on the type of  input
signal.
Input Signal Type                                             Menu Interface
Computer
DVI
HDTV
                                      Input, Picture, Color, PIP, Audio, Misc, Option, Language, Reset
S-Video
Video
YCbCr
                                     Input, Picture, Color, Video,...

EN-19
○○○○○○○○○○○
. English .
User’s ManualProjector
Input Menu
This menu allows to specify the signal source that you wish to project. This is particularly
useful if you have several sources (video and/or computer) connected to your projector.
Changing settings procedure (using either the Projector Control Panel or the Remote
Controller):
1.Press the MENU button to display OSD
   menu.
2.Press the 
c cc c
c or 
d dd d
d  button to select
   INPUT menu.
3.To enter the sub-menu setting, press
   the MENU...