ViewSonic Vt3200-l Manual

							Getting Started
2
Installing the LCD TV
Installing the Stand (For 42”)
Screw type1 x 5pcs
Screw type2 x 5pcs
TYPE1TYPE2
Place the display face down on a protective surface. Afterwards attach the neck piece onto the 
display and screw in the 5 screws to secure the neck. then insert the neck onto the bottom stand 
and secure the parts by inserting the screws and tightening them with the screwdriver provied.
Note: Attaching the stand requires two people.
Installing the Stand (For 32”)
Screw x 5 pcs
Place the display face down on a protective surface. Then insert the neck onto the bottom stand and 
secure the parts by inserting the screws and tightening them with the screwdriver provied.
Note: Attaching the stand requires two people. 
Disconnecting the Stand
To remove the stand, remove the screws in the circled area and the neck will come off. 
						

							Getting Started
3
Mounting ViewSonic LCD TV to the wall
The LCD TV can be used in a free standing position or wall-mounted. Before installing the product to 
the wall, please consider the following guidelines:
• Read the Important Safety Instructions, at the start of this manual. 
• Do not install in a moist or wet environment. This equipment is intended for indoor use.
• Do  not
• Use only ViewSonic approved wall-mounting brackets to support the LCD TV weight.
• Before attaching the wall mount plate to the back cover, ensure the product is working.
• ,I\RXU/&RXQHHGWR¿UVWUHPRYHWKHVWDQG
before mounting the device to the wall.
To attach the wall-mount bracket to LCD TV safely, please use the following guidelines:
• Disconnect the power and any other cables that might hinder moving the LCD TV. 
• Set the LCD TV on a table or work surface, placing the screen face down on a towel or woolen 
blanket to protect the screen surface from damage while installing plate.
• Before installing the LCD TV on the wall, ensure you have recorded the product serial number on 
page (i) of the User Guide, as you will need the serial number to request service should there be 
a service need.
• Install the wall mount plate to the LCD TV using screws NO LONGER than 20mm, as longer 
screws found in universal (non-ViewSonic) wall mount kits may damage the power supply 
causing the unit to fail. The wall-mount screw type is M6 x L20.
• Mount the wall mount bracket to the wall ensuring use of proper screws to support the 
installation. Ensure there is at least 3cm of space surrounding any air-vents of your LCD TV to 
allow adequate cooling during operation.
• Hang the LCD TV wall mount plate to the wall mount bracket, completing installation.  
Enjoy your ViewSonic LCD TV! 
						

							Getting Started
4
:DOO0RXQW.LW6SHFL
						

							Getting Started
5
FRONT View & SIDE View of the Product
1
2
3
4
5
6 7 8
Item Icon Description
1 Volume
VOL +Increase the volume.
Move to the right or adjust the setting on the OSD menu.
VOL -Decrease the volume.
Move to the left or adjust the setting on the OSD menu.
2 Channel SelectCH -Return to the previous channel.
CH  +Advance to the next channel.
3 Menu MENU
Turn the on-screen display (OSD) menu on / off.
4 Input INPUTSelect the input source.
Enter the submenu.
5 PowerTurn the power on from standby mode. Touch it again to 
return to standby mode.
6Remote Control 
ReceiverReceive IR signals from the remote control.
7 LED IndicatorBlue indicates power on. Red indicates standby mode.
8 Power SwitchTo switch the display on and off. 
						

							Getting Started
6
Rear View of the Product
Pr Pb Y VIDEO
 IN PC/VGA INTV
INPC/VGA
AUDIO
IN REMOTE
CONTROL
OUTAUDIO IN
RL
HDMI 1 HDMI 2 HDMI 3 SPDIF
OUTRS232
USBEARPHONE
OUT
8765234
1
13
12
10
9
11
Item Description
1 Power (AC input)Connect to the AC input power source.
2 Remote Control outputConnect to an IR emitter. This will enable the remote control of 
external equipment.
3 TV Input JackConnect to an antenna or cable TV.
4 VGA signal inputConnect to a PC VGA port.
5 PC/VGA Audio inputConnect to a PC line / audio port.
6 Composite Video inputConnect to the composite video output connectors on your A/V 
equipment.
7 Audio input (left/ right)Connect to the corresponding audio connectors on your A/V 
device.
8 YPbPr signal inputConnect to the YPbPr output of A/V device.
9 HDMI inputsConnect to the HDMI outputs of A/V devices.
10 SPDIF Optical outputConnect to the SPDIF input of A/V device.
11 RS232 signal inputReserved for the service technician’s use.
12 USB&RQQHFWWR86%GHYLFHVVXFKDV86%ÀDVKGULYH
13 Earphone JackConnect to earphones. By connecting the earphones, you can 
listen to the sound from the TV through the earphones.
j If you connect the earphones, the TV speakers will be muted. 
						

							Getting Started
7
Connecting the LCD TV
&DEOH6\VWHPRU9+)8+)$QWHQQD6\VWHP
PLQJDORQJZLWKVWDQGDUGGH¿QLWLRQ
analog programming.

• This TV is capable of receiving unscrambled digital programming for both cable and external VHF/
UHF antenna. 
• We strongly recommend that you connect the antenna/cable input using a 75-ohm coaxial cable 
(not supplied) to ensure the best picture quality. 
Cable or VHF/UHF
75-ohm coaxial cableRear side of the TV
VHF/UHF/CABLE input
&DEOH6\VWHPDQG9+)8+)$QWHQQD6\VWHP
Use an optional A-B RF switch (not supplied) to switch between the cable and antenna 
programming, as shown below.
Cable
AntennaRear side of the TV
VHF/UHF/CABLE input A-B RF switch

• Remember to set the TV/CATV setting in the TV menu to Air or Cable for the type you choose.
HD Cable Box/HD Satellite Box

						

							Getting Started
8
DVI Connection
HDMI 1 HDMI 2 HDMI 3 SPDIF
OUT
Pr Pb Y VIDEO
 IN PC/VGA
AUDIO
INAUDIO IN
RL
COMPONENT
VIDEO OUT
Pr YVIDEODVI-HDTV OUT
HDMI OUT
OUTIN
AUDIOL R
Pb
LINE OUT
Audio cable
DVI-to-HDMI cable Rear side of the TV
DVI-to-HDMI cableCATV / Satellite 
antenna cableDVI-to-HDMI adapterAudio cable HD cable box /  
HD satellite box

• For DVI connection, connect the HDMI jack (with DVI-to-HDMI cable or adapter), and connect the 
audio jack to the AUDIO IN jacks of PC Audio input.
HDMI Timing Reference Chart
No. Mode HDMI DVI
1 VGA60 (640x480) V V
2 SVGA60 (800x600) V V
3 XGA60 (1024x768) V V
4 SXGA60 (1280x1024) V V
5 WXGA60 (1360x768) NA NA
6 1280 x 800 NA NA
7 1440 x 900 NA NA
8 1680 x 1050 NA NA
9 1920 x 1080 V V
10 480i60 V V
11 576i50 V V
12 480P60 V V
13 576P50 V V
14 720P50 V V
15 720P60 V V
16 1080I50 V V
17 1080I60 V V
18 1080P50 V V
19 1080P60 V V
20 1080P24 NA NA
21 1080P30 NA NA 
						

							Getting Started
9
YPbPr or Component Connection
Pr Pb Y VIDEO
 IN PC/VGA
AUDIO
INAUDIO IN
RL
COMPONENT
VIDEO OUT
Pr YVIDEODVI-HDTV OUT
HDMI OUT
OUTIN
AUDIOL R
Pb
LINE OUT
Audio cableComponent  
cable Rear side of the TV
Component cableCATV / Satellite 
antenna cableAudio cableHD cable box /  
HD satellite box

• YPbPr provides better quality than the AV connection.
AV Connection
COMPONENT
VIDEO OUT
Pr YVIDEODVI-HDTV OUT
HDMI OUT
OUTIN
AUDIOL R
Pb
LINE OUT
Pr Pb Y VIDEO
 IN PC/VGA
AUDIO
INAUDIO IN
RL
AV cable
AV cableCATV / Satellite 
antenna cable HD cable box /  
HD satellite box 
						

							Getting Started
10
Programming your Cable or Satellite Box remote
Refer to the user manual from your service provider to determine the setting.
If it requires:
• 3 digits, please try “566”, “565”, “556”, or “688”. It usually works with DISHNetwork.
• 4 digits, please try “0054”. It usually works with Cox.
• 5-digits, please try “11454”, “11054”, or “10690”. It usually works with DIRECTV.
Personal Computer
Use the LCD TV as the monitor of your computer.
HDMI 1 HDMI 2 HDMI 3 SPDIF
OUT
VIDEO
 IN PC/VGA INTV
INPC/VGA
AUDIO
IN REMOTE
CONTROL
OUT
Audio cable (stereo mini plugs)
VGA 15 Pin cableRear side of the TV

• Connect the PC IN jack to the PC using a 15-pin cable and audio cable.
PC Timing Reference Chart
No.9*$7LPLQJPanel FullHD (1920 x 1080) Support
Mode Resolution H sync 
(kHz)V sync 
(Hz)Pixel clock 
(MHz)Polarity Support
1 IBM VGA 720 x 400 31.47 70.09 28.32 N/P V
2 VESA DMT 640 x 480 31.5 59.94 25.175 N/N V
3 VESA DMT 800 x 600 37.88 60.32 40 P/P V
4 VESA DMT 1024 x 768 48.36 60 65 N/N V
5VESA DMT
1280 x 768 47.77 59.8 79.5 N/P V
6 VESA DMT 1280 x 800 49.7 59.81 83.5 N/P NA
7 VESA DMT 1280 x 1024 63.98 60.02 108 P/P V
8 VESA DMT 1360 x 768 47.71 60.01 85.5 P/P NA
9 VESA DMT 1440 x 900 55.94 59.89 106.5 N/P NA
10 VESA DMT 1680 x 1050 65.29 59.95 146.25 N/P NA
11 CEA 1920 x 1080 67.5 60 148.5 P/P V

• This TV PC VGA input does not support interlaced signals. 
						

							11
Remote Control and TV Controls
Inserting Remote Control Batteries
1. Remove the battery cover by pulling then lifting the knob on the cover.
2. Insert the batteries, corresponding to the (+) and (-) markings on the battery compartment.
3. Reattach the battery cover.
 CAUTION
• 2QO\XVHWKHVSHFL