ViewSonic VG2021m Manual

							ViewSonicVG2021m 8
Using the LCD Display
Setting the Timing Mode
Setting the timing mode is important for maximizing the quality of the screen image and 
minimizing eye strain. The timing mode consists of the resolution (example 1400 x 1050) and 
refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the 
OSD (On-screen Display) controls to adjust the screen image.
For the best picture quality set your LCD display timing mode to:
VESA 1400 x 1050 @ 60Hz.
To set the Timing Mode:
1. Set the resolution: Right-click on the Windows desktop > Properties > Settings > set the 
resolution.
2. Set the refresh rate: See your graphic cards user guide for instructions.
WARNING: Do not set the graphics card in your computer to exceed the maximum refresh 
rate of 75Hz; doing so may result in permanent damage to your LCD display
.
OSD and Power Lock Settings
•OSD Lock: Press and hold [1] and the up arrow S for 10 seconds. If any buttons are 
pressed the message OSD Locked will display for 5 seconds.
•OSD Unlock: Press and hold [1] and the up arrow S again for 10 seconds.
•Power Button Lock: Press and hold [1] and the down arrow T for 10 seconds. If the 
power button is pressed the message Power Button Locked will display for 5 seconds. With 
or without this setting, after a power failure, your LCD display’s power will automatically 
turn ON when power is restored.
•Power Button Unlock: Press and hold [1] and the down arrow T again for 10 seconds.
 
						

							ViewSonicVG2021m 9
Adjusting the Screen Image
Use the buttons on the front control panel to display and adjust the OSD controls which display 
on the screen. The OSD controls are explained at the top of the next page and are defined in 
“Main Menu Controls” on page 11.
Main Menu
with OSD controls
Front Control Panel
shown below in detail
Scrolls through menu options and adjusts the displayed control.
Also a shortcut to display the Contrast adjustment control screen. Power light
Blue = ON
Orange = Power Saving Standby Power On/Off
Displays the Main Menu or exits the control screen and saves 
adjustments. Audio Mute button turns the sound off
Displays the control screen for the highlighted control.
Also toggles between two controls on some screens.
Also a shortcut to toggle analog and digital connection.
 
						

							ViewSonicVG2021m 10 Do the following to adjust the display setting:
1.To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15 
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2.To select a control to adjust, pressSorTto scroll up or down in the Main Menu.
3.After the desired control is selected, press button [2]. A control screen like the one shown 
below appears.
4.To adjust the setting, press the up S or down T buttons.
5.To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
• Adjust the computers graphics card so that it outputs a 1400 x 1050 @ 60Hz video signal to 
the LCD display. (Look for instructions on “changing the refresh rate” in the graphics cards 
user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the 
screen image is completely visible
. (The black border around the edge of the screen should 
barely touch the illuminated “active area” of the LCD display.)
The command line at the bottom of the
control screen tells what to do next from
this screen. You can toggle between control
screens, adjust the selected option, or exit
the screen.
 
						

							ViewSonicVG2021m 11
Main Menu Controls
Adjust the menu items shown below by using the up S and down T buttons.
Control Explanation
Auto Image Adjust sizes and centers the screen image automatically.
Contrast adjusts the difference between the image background (black level) 
and the foreground (white level).
Brightness adjusts background black level of the screen image.
Audio Adjust
Vo l u m e increases the volume, decreases the volume, and mutes the audio.
Mute temporarily silences audio output.
Color Adjust provides several color adjustment modes, including preset color 
temperatures and a User Color mode which allows independent adjustment of 
red (R), green (G), and blue (B). The factory setting for this product is 6500K 
(6500 Kelvin).
sRGB-This is quickly becoming the industry standard for color management, 
with support being included in many of the latest applications. Enabling this 
setting allows the LCD display to more accurately display colors the way they 
were originally intended. Enabling the sRGB setting will cause the Contrast and 
Brightness adjustments to be disabled.
9300K-Adds blue to the screen image for cooler white (used in most office 
settings with fluorescent lighting).
6500K-Adds red to the screen image for warmer white and richer red.
5400K-Adds green to the screen image for a darker color.
5000K-Adds blue and green to the screen image for a darker color.
 
						

							ViewSonicVG2021m 12
Control Explanation
User Color Individual adjustments for red (R), green (G), and blue (B).
1.To select color (R, G or B) press button [2].
2.To adjust selected color, pressSandT.
Important: If you select RECALL from the Main Menu when the product is 
set to a Preset Timing Mode, colors return to the 6500K factory preset.
Information displays the timing mode (video signal input) coming from the 
graphics card in the computer, the LCD model number, the serial number, and 
the ViewSonic
® website URL. See your graphics card’s user guide for 
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1400 x 1050 @ 60Hz (recommended) means that the resolution 
is 1400 x 1050 and the refresh rate is 60 Hertz.
Manual Image Adjust Sub-menu
H. Size (Horizontal Size) adjusts the width of the screen image.
H./V. Position (Horizontal/Vertical Position) moves the screen image left or 
right and up or down.
 
						

							ViewSonicVG2021m 13
Control Explanation
Fine Tune sharpens the focus by aligning text and/or graphics with pixel 
boundaries.
NOTE: Try Auto Image Adjust first.
Sharpness adjusts the clarity and focus of the screen image.
Setup Menu displays the menu shown below:
Language Select allows the user to choose the language used in the menus and 
control screens.
Resolution Notice allows the user to enable or disable this notice.
If you enable the Resolution Notice shown above and your computer is set at a 
resolution other than 1400 x 1050, the following screen appears.
 
						

							ViewSonicVG2021m 14
Control Explanation
OSD Position allows the user to move the OSD menus and control screens.
OSD Timeout sets the length of time the OSD screen is displayed. For example, 
with a “30 second” setting, if a control is not pushed within 30 seconds, the 
display screen disappears.
OSD Background allows the user to turn the OSD background On or Off.
Memory Recall returns the adjustments back to factory settings if the display is 
operating in a factory Preset Timing Mode listed in the Specifications of this 
manual.
 
						

							ViewSonicVG2021m 15
Other Information
Specifications
1 Macintosh computers older than G3 require a ViewSonic® Macintosh adapter. To order an adapter, contact 
ViewSonic.LCDTy p e
Color Filter
Glass Surface20” (full 20 viewable diagonal area),
TFT (Thin Film Transistor), Active Matrix SXGA+ LCD,
0.2916 mm pixel pitch
RGB vertical stripe
Anti-Glare
Input SignalVideo
SyncRGB analog (0.7/1.0 Vp-p, 75 ohms)
Separate Sync,
f
h:30-82 kHz, fv:56-76 Hz
CompatibilityPC
Macintosh
1
Up to 1400 x 1050 Non-interlaced
Power Macintosh up to 1400 x 1050
ResolutionRecommended
and supported1400 x 1050 @ 60 Hz
1280 x 1024 @ 60, 70, 72 Hz
1024 x 768 @ 60, 70, 72, 75 Hz
800 x 600 @ 56, 60, 72, 75 Hz
640 x 480 @ 60, 75 Hz
720 x 400 @ 70 Hz
PowerVoltage 100-240 VAC, 50-60 Hz (auto switch)
Display areaFull Scan 408.24 mm (H) x 306.18 mm (V)
16.1 (H) x 12.1 (V)
Operating
conditionsTemperature
Humidity
Altitude41° F to + 95° F (5° C to + 35° C)
20% to 80% (non-condensing)
To 10,000 feet
Storage
conditionsTemperature
Humidity
Altitude-4° F to + 131° F (-20° C to + 55° C)
20% to 85% (non-condensing)
To 40,000 feet
DimensionsPhysical 459 mm (W) x 465 mm (H) x 205 mm (D)
18.1 (W) x 18.3 (H) x 8.1 (D)
WeightPhysical 13.7 lb (6.2 kg)
RegulationsBSMI, CCC, PSB, C-Tick, CE, GS, MIC, VCCI,
Ergo, Gost-R/Hygienic, SASO, TCO03,
UL/cUL, FCC-B, ICES-B, NOM, TUV-S, E
NERGY STA R®
Power saving
modesOn
OffNormal              (blue LED)

						

							ViewSonicVG2021m 16
Troubleshooting
No power
• Make sure power button (or switch) is ON.
• Make sure A/C power cord is securely connected to the LCD display.
• Plug another electrical device (like a radio) into the power outlet to verify that the outlet is 
supplying proper voltage.
Power is ON but no screen image
• Make sure the video cable supplied with the LCD display is tightly secured to the video 
output port on the back of the computer. If the other end of the video cable is not attached 
permanently to the LCD display, tightly secure it to the LCD display.
• Adjust brightness and contrast.
• If you are using an Macintosh older than G3, you need a Macintosh adapter.
Wrong or abnormal colors
• If any colors (red, green, or blue) are missing, check the video cable to make sure it is 
securely connected. Loose or broken pins in the cable connector could cause an improper 
connection.
• Connect the LCD display to another computer.
• If you have an older graphics card, contact ViewSonic
® for a non-DDC adapter.
Control buttons do not work
• Press only one button at a time.
 
						

							ViewSonicVG2021m 17
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
Country/RegionWebsite T = Telephone
F = FAXEmail
United States www.viewsonic.com/supportT= 800 688 6688
F= 909 468 [email protected]
Canada www.viewsonic.com/support T= 866 463 4775 [email protected]
United Kingdom www.viewsoniceurope.com/uk T= 0207 949 0307
Europe, Middle 
East, Baltic 
countries, and North 
Africawww.viewsoniceurope.com (Contact your reseller)
Australia and New 
Zealandwww.viewsonic.com.au/support/AUS= 1800 880 818
NZ= 0800 008 [email protected]
Singapore/Malaysia/
Thailandwww.viewsonic.com.sg/support/ T= 65 64616044 [email protected]
South Africa and 
other countrieswww.viewsonic.comT= 886 2 2246 3456
F= 886 2 2249 [email protected]
India www.in.viewsonic.com T= 1800 11 9999 [email protected] 
Hong Kong www.hk.viewsonic.com/support/ T= 852 3102 2900 [email protected]
Macau www.hk.viewsonic.com/support/ T= 853 700 303 [email protected]
Korean www.viewsonic.com T= 080 333 2131 [email protected]