ViewSonic VE510B Manual

							ViewSonicVE510b/VE510s 7
Using the LCD Display
Setting the Timing Mode
Setting the timing mode is important for maximizing the quality of the screen image and
minimizing eye strain. The timing mode consists of the resolution (example 1024 x 768) and
refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the
OSD (On Screen Display) controls to adjust the screen image.
For the best picture quality set your LCD display timing mode to:
VESA 1024 x 768 @ 60Hz.
To set the Timing Mode:
1. Set the resolution: Right-click on the Windows desktop > Properties > Settings > set the 
resolution.
2. Set the refresh rate: See your graphic cards user guide for instructions.
WA R N I N G :  Do not set the graphics card in your computer to exceed the maximum refresh
rate of 75Hz; doing so may result in permanent damage to your LCD display
.
OSD and Power Lock Settings
•OSD Lock: Press and hold [1] and the up arrow S for 10 seconds. If any buttons are
pressed the message OSD Locked will display for 5 seconds.
•OSD Unlock: Press and hold [1] and the up arrow S again for 10 seconds.
•Power Button Lock: Press and hold [1] and the down arrow T for 10 seconds. If the
power button is pressed the message Power Button Locked will display for 5 seconds. With
or without this setting, after a power failure, your LCD display’s power will automatically
turn ON when power is restored.
•Power Button Unlock: Press and hold [1] and the down arrow T again for 10 seconds.
 
						

							ViewSonicVE510b/VE510s 8
Adjusting the Screen Image
Use the buttons on the front control panel to display and adjust the OSD controls which display
on the screen. The OSD controls are explained at the top of the next page and are defined in
“Main Menu Controls” on page 9.
Main Menu
with OSD controls
Front Control Panel
shown below in detail
Scrolls through 
menu options and 
adjusts the 
displayed control.
Also a shortcut to 
display the 
Contrast 
adjustment control 
screen.
Displays the control screen
for the highlighted control.
Also toggles between two
controls on some screens.
Also a shortcut to Auto
Image Adjust.Power light
Green = ON
Orange = Power Saving
Standby Power 
On/Off
Displays the
Main Menu or
exits the
control screen
and saves
adjustments.
 
						

							ViewSonicVE510b/VE510s 9 Do the following to adjust the display setting:
1.To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15 
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2.To select a control to adjust, pressSorTto scroll up or down in the Main Menu.
3.After the desired control is selected, press button [2]. A control screen like the one shown 
below appears.
4.To adjust the setting, press the upSor downTbuttons.
5.To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
• Adjust the computers graphics card so that it outputs a 1024 x 768 @ 60Hz video signal to
the LCD display. (Look for instructions on “changing the refresh rate” in the graphics cards
user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the
screen image is completely visible
. (The black border around the edge of the screen should
barely touch the illuminated “active area” of the LCD display.)
The line at the bottom of the screen shows
the current functions of buttons 1 and 2:
Exit or select the Brightness control.
 
						

							ViewSonicVE510b/VE510s 10
Main Menu Controls
Adjust the menu items shown below by using the upSand downTbuttons.
Control Explanation
Auto Image Adjust automatically sizes, centers, and fine tunes the video signal
to eliminate waviness and distortion. Press the [2] button to execute Auto Image
Adjust.
NOTE: Auto Image Adjust works with most common video cards. If this
function does not work on your LCD display, then lower the video refresh rate
to 60 Hz and set the resolution to its pre-set value.
Contrast adjusts the difference between the image background (black level)
and the foreground (white level).
Brightness adjusts background black level of the screen image.
Color Adjust provides several color adjustment modes, including preset color
temperatures and a User Color mode which allows independent adjustment of
red (R), green (G), and blue (B). The factory setting for this product is 6500K
(6500 Kelvin).
sRGB - This is quickly becoming the industry standard for color management,
with support being included in many of the latest applications. Enabling this
setting allows the LCD display to more accurately display colors the way they
were originally intended. Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.
9300K - Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K - Adds red to the screen image for warmer white and richer red.
5400K - Adds green to the screen image for a darker color.
 
						

							ViewSonicVE510b/VE510s 11 Control Explanation
User Color - Individual adjustments for red (R), green (G), and blue (B).
1.To select color (R, G or B) press button [2].
2.To adjust selected color, pressSorT.
3.When all color adjustments are complete, press button [1] twice.
Information displays the timing mode (video signal input) coming from the
graphics card in the computer, the LCD model number, the serial number, and
the ViewSonic
® website URL. See your graphics card’s user guide for
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1024 x 768 @ 60Hz (recommended) means that the resolution is
1024 x 768 and the refresh rate is 60 Hertz.
Manual Image Adjust
H./V. Position (Horizontal/Vertical Position) moves the screen image left or
right and up or down. Press button [2] to toggle between Horizontal and
Vertical. The Horizontal setting moves the screen image to the left or to the
right. The Vertical setting moves the screen image up and down.
H. Size (Horizontal Size) adjusts the width of the screen image.
Fine Tune sharpens the focus by aligning text and/or graphics with pixel
boundaries.
NOTE: Try the Auto Adjust function before using the Fine Tune control.
Sharpness adjusts the clarity and focus of the screen image.
 
						

							ViewSonicVE510b/VE510s 12 Control Explanation
Setup menu displays the menu shown below:
Language Select allows the user to choose the language used in the menus and 
control screens.
Resolution Notice advises the optimal resolution to use.
OSD Position allows the user to move the on-screen display menus and control
screens.
OSD Timeout sets the length of time the on-screen display screen is displayed.
For example, with a “15 second” setting, if a control is not pushed within 15
seconds, the display screen disappears.
OSD Background allows the user to turn the On-Screen Display background
On or Off.
Memory Recall returns the adjustments back to factory settings if the display is 
operating in a factory Preset Timing Mode listed in the Specifications of this 
manual.
 
						

							ViewSonicVE510b/VE510s 13
Other Information
Specifications
1 Macintosh computers older than G3 require a ViewSonic® Macintosh adapter. To order an adapter, contact
ViewSonic.LCDTy p e
Color Filter
Glass Surface15” (full 15 viewable diagonal area),
TFT (Thin Film Transistor), Active Matrix XGA LCD,
0.297 mm pixel pitch
RGB vertical stripe
Anti-Glare
Panel tilt+20°, -5°
Input SignalVideo
SyncRGB analog (0.7/1.0 Vp-p, 75 ohms)
Separate Sync
f
h:30-62 kHz, fv:50-75 Hz
CompatibilityPC
Macintosh
1
Up to 1024 x 768 Non-interlaced
Power Macintosh up to 1024 x 768
ResolutionRecommended
and supported1024 x 768 @ 60, 70, 72, 75 Hz
832 x 624 @ 75 Hz
800 x 600 @ 56, 60, 72, 75 Hz
720 x 400 @ 70 Hz
640 x 480 @ 60, 67, 72, 75 Hz
PowerVoltage 100-240 VAC, 50/60 Hz (auto switch)
Display areaFull Scan 304.1 mm (H) x 228.1 mm (V)
12.0 (H) x 9.0 (V)
Operating
conditionsTemperature
Humidity
Altitude32° F to + 104° F (0° C to + 40° C)
10% to 90% (non-condensing)
To 10,000 feet
Storage
conditionsTemperature
Humidity
Altitude-4° F to + 140° F (-20° C to + 60° C)
5% to 90% (non-condensing)
To 40,000 feet
DimensionsPhysical 343 mm (W) x 326 mm (H) x 55 mm (D)
13.5 (W) x 12.8 (H) x 2.2 (D)
WeightNet 6.6 lb (3.0 kg)
RegulationsBSMI, CCC, PSB, C-Tick,PCBC
CE, GS, Ergo, Gost-R/Hygienic, SASO, TCO99,
UL/cUL, FCC-B, ICES-B, NOM, TUV-S, E
NERGY STAR®, ENERGY
Power saving
modesOn
OffNormal              (green LED)

						

							ViewSonicVE510b/VE510s 14
Troubleshooting
No power
• Make sure power button (or switch) is ON.
• Make sure A/C power cord is securely connected to the LCD display.
• Plug another electrical device (like a radio) into the power outlet to verify that the outlet is
supplying proper voltage.
Power is ON but no screen image
• Make sure the video cable supplied with the LCD display is tightly secured to the video
output port on the back of the computer. If the other end of the video cable is not attached
permanently to the LCD display, tightly secure it to the LCD display.
• Adjust brightness and contrast.
• If you are using an Macintosh older than G3, you need a Macintosh adapter.
Wrong or abnormal colors
• If any colors (red, green, or blue) are missing, check the video cable to make sure it is
securely connected. Loose or broken pins in the cable connector could cause an improper
connection.
• Connect the LCD display to another computer.
• If you have an older graphics card, contact ViewSonic
® for a non-DDC adapter.
Control buttons do not work
• Press only one button at a time.
 
						

							ViewSonicVE510b/VE510s 15
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
Country/
RegionWebsite T = Telephone
F = FAXEmail
United States www.viewsonic.com/supportT= (800) 688 6688
F= (909) 468 [email protected]
Canada www.viewsonic.com/supportT= (886) 463 4775
F= (909) 468 [email protected]
United 
Kingdomwww.viewsoniceurope.comT= (0800) 833 648
F= +44 (0) 1293 643 [email protected]
Europe, 
Middle East, 
Baltic 
countries, and 
North Africawww.viewsoniceurope.com (Contact your reseller) [email protected]
Australia and 
New Zealandwww.viewsonic.com.auAUS= 1800 880 818
NZ= 0800 008 [email protected]
Singapore, 
Southeast 
Asia, and Indiawww.viewsonic.com.sgT=+ 65 273 4018
F=+ 65 273 [email protected]
South Africa 
and other 
countrieswww.viewsonic.comT=+886 (2) 2246 3456
F=+886 (2) 8242 [email protected]
Hong Kong www.hk.viewsonic.comT=+886 (2) 2246 3456
F=+886 (2) 8242 [email protected]
 
						

							ViewSonicVE510b/VE510s 16
Cleaning the LCD Display
• MAKE SURE THE LCD DISPLAY IS TURNED OFF.
• NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE.
To clean the screen:
1.Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2.If the screen still not clean, apply a small amount of non-ammonia
, non-alcohol based glass 
cleaner onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1.Use a soft, dry cloth.
2.If the case still not clean, apply a small amount of a non-ammonia
, non-alcohol based, mild 
non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface.
Disclaimer
• ViewSonic
® does not recommend the use of any ammonia or alcohol-based cleaners on the
LCD display screen or case. Some chemical cleaners have been reported to damage the
screen and/or case of the LCD display.
• ViewSonic will not be liable for damage resulting from use of any ammonia or alcohol-
based cleaners.