ViewSonic VA926g Manual

ViewSonicVA926g 9
Adjusting the Screen Image
Use the buttons on the front control panel to display and adjust the OSD controls which display 
on the screen. The OSD controls are explained at the top of the next page and are defined in 
“Main Menu Controls” on page 11.
Main Menu
with OSD controls
Front Control Panel
shown below in detail
Displays the control screen for
the highlighted control.
Also toggles between two
controls on some screens.
Also a shortcut to toggle
analog and digital connection.Power...

ViewSonicVA926g 10 Do the following to adjust the display setting:
1.To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15 
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2.To select a control to adjust, pressorto scroll up or down in the Main Menu.
3.After the desired control is selected, press button [2]. A control screen like the one shown 
below appears.
4.To adjust the control, press the up  or...

ViewSonicVA926g 11
Main Menu Controls
Adjust the menu items shown below by using the up  and down  buttons.
Control Explanation
Auto Image Adjust automatically sizes, centers, and fine tunes the video signal 
to eliminate waviness and distortion. Press the [2] button to obtain a sharper 
image.
NOTE: Auto Image Adjust works with most common video cards. If this 
function does not work on your LCD display, then lower the video refresh rate 
to 60 Hz and set the resolution to its pre-set value.
Contrast...

ViewSonicVA926g 12
Control Explanation
7500K-Adds blue to the screen image for cooler white (used in most office 
settings with fluorescent lighting).
6500K-Adds red to the screen image for warmer white and richer red.
5000K-Adds green to the screen image for a darker color.
User Color Individual adjustments for red (R), green (G), and blue (B).
1.To select color (R, G or B) press button [2].
2.To adjust selected color, pressand.
Important: If you select RECALL from the Main Menu when the product is...

ViewSonicVA926g 13
Control Explanation
Fine Tune sharpens the focus by aligning text and/or graphics with pixel 
boundaries.
NOTE: Try Auto Image Adjust first.
Sharpness adjusts the clarity and focus of the screen image.
Dynamic Contrast allows the user to turn the contrast ratio enhancement on or 
off.
ECO Mode provides the lower power consumption by reducing the brightness. 
Standard: The default brightness setting.
Optimize: Decreases the brightness by 25 %.
Conserve: Decreases the brightness by 50...

ViewSonicVA926g 14
Other Information
Specifications
1 Macintosh computers older than G3 require a ViewSonic® Macintosh adapter. To order an adapter, contact
ViewSonic.LCDTy p e
Display Size
Color Filter
Glass SurfaceTFT (Thin Film Transistor), Active Matrix 1280 x 1024 LCD,
0.294 mm pixel pitch
Metric: 48 cm
Imperial: 19” (19” viewable)
RGB vertical stripe
Anti-Glare
Input SignalVideo Sync RGB analog (0.7/1.0 Vp-p, 75 ohms)
Separate Sync
f
h:24-82 kHz, fv:50-75 Hz
CompatibilityPC
Macintosh
1Up to 1280 x...

ViewSonicVA926g 15
Troubleshooting
No power
• Make sure power button (or switch) is ON.
• Make sure A/C power cord is securely connected to the LCD display.
• Plug another electrical device (like a radio) into the power outlet to verify that the outlet is
supplying proper voltage.
Power is ON but no screen image
• Make sure the video cable supplied with the LCD display is tightly secured to the video
output port on the back of the computer. If the other end of the video cable is not attached
permanently...

ViewSonicVA926g 16
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
Country/RegionWebsite T = Telephone
F = FAXEmail
Australia/New Zealand www.viewsonic.com.auAUS= 1800 880 818
NZ= 0800 008 [email protected]
Canada www.viewsonic.comT (Toll-Free)= 1-866-463-4775  
T (Toll)= 1-424-233-2533
F= [email protected]
Europe www.viewsoniceurope.com...

ViewSonicVA926g 17
Cleaning the LCD Display
• MAKE SURE THE LCD DISPLAY IS TURNED OFF.
• NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE.
To clean the screen:
1.Wipe the screen with a clean, soft, lint-free cloth. This removes dust and other particles.
2.If the screen still not clean, apply a small amount of non-ammonia
, non-alcohol based glass 
cleaner onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1.Use a soft, dry cloth.
2.If the case still not clean,...

ViewSonicVA926g 18
Limited Warranty
VIEWSONIC® LCD DISPLAY
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under 
normal use, during the warranty period. If a product proves to be defective in material or 
workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace 
the product with a like product. Replacement product or parts may include remanufactured or 
refurbished parts or components.
How long the...