ViewSonic VA2626wm Manual

							ViewSonicVA2626wm 8
Using the LCD Display
Setting the Timing Mode
Setting the timing mode is important for maximizing the quality of the screen image and
minimizing eye strain. The timing mode consists of the resolution (example 1920 x 1200) and
refresh rate (or vertical frequency; example 60 Hz). After setting the timing mode, use the
OSD (On-screen Display) controls to adjust the screen image.
For the best picture quality set your LCD display timing mode to:
VESA 1920 x 1200 @ 60Hz.
To set the Timing Mode:
1. Set the resolution: Right-click on the Windows desktop > Properties > Settings > set the 
resolution.
2. Set the refresh rate: See your graphic cards user guide for instructions.
WARNING: Do not set the graphics card in your computer to exceed the maximum refresh
rate of 75Hz; doing so may result in permanent damage to your LCD display
.
OSD and Power Lock Settings
•OSD Lock: Press and hold [1] and the up arrow S for 10 seconds. If any buttons are
pressed the message OSD Locked will display for 5 seconds.
•OSD Unlock: Press and hold [1] and the up arrow S again for 10 seconds.
•Power Button Lock: Press and hold [1] and the down arrow T for 10 seconds. If the
power button is pressed the message Power Button Locked will display for 5 seconds. With
or without this setting, after a power failure, your LCD display’s power will automatically
turn ON when power is restored.
•Power Button Unlock: Press and hold [1] and the down arrow T again for 10 seconds.
Dynamic Contrast
•DCR On/Off: Press S for 3 seconds to turn DCR On or Off.
 
						

							ViewSonicVA2626wm 9
Adjusting the Screen Image
Use the buttons on the front control panel to display and adjust the OSD controls which display 
on the screen. The OSD controls are explained at the top of the next page and are defined in 
“Main Menu Controls” on page 11.
Main Menu
with OSD controls
Front Control Panel
shown below in detail
Scrolls through 
menu options and 
adjusts the 
displayed control.
Also a shortcut to 
display the Contrast/
Brightness 
adjustment control 
screen.
Displays the control screen
for the highlighted control.
Also toggles between three
controls on some screens.
Also a shortcut to Auto
Image Adjust.Power light
Blue = ON
Orange = Power Saving
Standby Power On/Off
Displays the
Main Menu or
exits the
control screen
and saves
adjustments.
 
						

							ViewSonicVA2626wm 10 Do the following to adjust the display setting:
1.To display the Main Menu, press button [1].
NOTE: All OSD menus and adjustment screens disappear automatically after about 15 
seconds. This is adjustable through the OSD timeout setting in the setup menu.
2.To select a control to adjust, pressSorTto scroll up or down in the Main Menu.
3.After the desired control is selected, press button [2]. A control screen like the one shown 
below appears.
4.To adjust the control, press the up S or down T buttons.
5.To save the adjustments and exit the menu, press button [1] twice.
The following tips may help you optimize your display:
• Adjust the computers graphics card so that it outputs a 1920 x 1200 @ 60Hz video signal to
the LCD display. (Look for instructions on “changing the refresh rate” in the graphics cards
user guide.)
• If necessary, make small adjustments using H. POSITION and V. POSITION until the
screen image is completely visible
. (The black border around the edge of the screen should
barely touch the illuminated “active area” of the LCD display.)
The line at the bottom of the screen shows
the current functions of buttons 1 and 2:
Exit or select the Brightness control.
 
						

							ViewSonicVA2626wm 11
Main Menu Controls
Adjust the menu items shown below by using the up S and down T buttons.
Control Explanation
Auto Image Adjust automatically sizes, centers, and fine tunes the video signal 
to eliminate waviness and distortion. Press the [2] button to obtain a sharper 
image.
NOTE: Auto Image Adjust works with most common video cards. If this 
function does not work on your LCD display, then lower the video refresh rate 
to 60 Hz and set the resolution to its pre-set value.
Contrast adjusts the difference between the image background (black level) 
and the foreground (white level).
Brightness adjusts background black level of the screen image.
Input Select toggles between inputs if you have more than one computer 
connected to the LCD Display.
NOTE: HDMI input/exit mode must be selected manually by OSD menu or hot 
key control.
Audio Adjust
Vo l u m e increases the volume, decreases the volume, and mutes the audio.
Mute temporarily silences audio output.
Color Adjust provides several color adjustment modes, including preset color 
temperatures and a User Color mode which allows independent adjustment of 
red (R), green (G), and blue (B). The factory setting for this product is 6500K 
(6500 Kelvin).
 
						

							ViewSonicVA2626wm 12
Control Explanation
sRGB-This is quickly becoming the industry standard for color management,
with support being included in many of the latest applications. Enabling this
setting allows the LCD display to more accurately display colors the way they
were originally intended. Enabling the sRGB setting will cause the Contrast and
Brightness adjustments to be disabled.
9300K-Adds blue to the screen image for cooler white (used in most office
settings with fluorescent lighting).
6500K-Adds red to the screen image for warmer white and richer red.
5400K-Adds green to the screen image for a darker color.
User Color Individual adjustments for red (R), green (G), and blue (B).
1.To select color (R, G or B) press button [2].
2.To adjust selected color, pressSandT.
Important: If you select RECALL from the Main Menu when the product is 
set to a Preset Timing Mode, colors return to the 6500K factory preset.
Information displays the timing mode (video signal input) coming from the 
graphics card in the computer, the LCD model number, the serial number, and 
the ViewSonic
® website URL. See your graphics card’s user guide for 
instructions on changing the resolution and refresh rate (vertical frequency).
NOTE: VESA 1920 x 1200 @ 60Hz (recommended) means that the resolution 
is 1920 x 1200 and the refresh rate is 60 Hertz.
 
						

							ViewSonicVA2626wm 13
Control Explanation
Manual Image Adjust displays the Manual Image Adjust menu.
H./V. Position (Horizontal/Vertical Position) moves the screen image left or 
right and up or down.
H. Size (Horizontal Size) adjusts the width of the screen image.
Fine Tune sharpens the focus by aligning text and/or graphics with pixel 
boundaries.
NOTE: Try Auto Image Adjust first.
Sharpness adjusts the clarity and focus of the screen image.
Display Mode provides two color space modes. The factory setting for this 
product is PC mode. 
PC mode sets color space to RGB for PC timing mode.
HD mode sets color space to YUV for HD timing mode.
Aspect ratio Selects the image size for 4:3 and full screen.
ECO Mode provides the lower power consumption by reducing the brightness. 
Standard: The default brightness setting 
Optimize: Decreases the brightness by 25 % 
Conserve: Decreases the brightness by 50 %
NOTE: When the ECO Mode is set to Optimize or Conserve, the 
Brightness, Contrast, and Dynamic Contrast cannot be adjusted.
 
						

							ViewSonicVA2626wm 14
Control Explanation
Setup Menu displays the menu shown below:
Language Select allows the user to choose the language used in the menus and 
control screens.
Resolution Notice advises the optimal resolution to use.
OSD Position allows the user to move the OSD menus and control screens.
OSD Timeout sets the length of time the OSD screen is displayed. For 
example, with a “15 second” setting, if a control is not pushed within 15 
seconds, the display screen disappears.
OSD Background allows the user to turn the OSD background On or Off.
Sleep Set up the auto power off time for 30/45/60/120 minutes. (Its inactive in 
D-SUB/DVI mode only)
Memory Recall returns the adjustments back to factory settings if the display is 
operating in a factory Preset Timing Mode listed in the Specifications of this 
manual.
Exception: This control does not affect changes made with the User Color 
control, Language Select or Power Lock setting.
 
						

							ViewSonicVA2626wm 15
Other Information
Specifications
1 Macintosh computers older than G3 require a ViewSonic® Macintosh adapter. To order an adapter, contact
ViewSonic.LCDTy p e
Color Filter
Glass Surface26” (full 25.54 wide viewable diagonal area),
TFT (Thin Film Transistor), Active Matrix WUXGA LCD,
0.2865 mm pixel pitch
RGB vertical stripe
Anti-Glare
Input SignalVideo Sync RGB analog (0.7/1.0 Vp-p, 75 ohms)
HDMI/DVI-D (TMDS digital, 100ohms)
Composite Sync, Separate Sync, Sync on Green
f
h:24-82 kHz, fv:50-75 Hz
CompatibilityPC
Macintosh
1Up to 1920 x 1200 Non-interlaced
Power Macintosh up to 1920 x 1200
ResolutionRecommended
and supported1920 x 1200 @ 60 Hz
1680 x 1050 @ 60 Hz
1600 x 1200 @ 60 Hz
1440 x 900 @ 60, 75 Hz
1280 x 1024 @ 60, 75 Hz
1024 x 768 @ 60, 70, 72, 75 Hz
800 x 600 @ 56, 60, 72, 75 Hz
640 x 480 @ 60, 75 Hz
720 x 400 @ 70 Hz
Video Timing 
(HDMI)Recommended
and supported480i / 480p / 576i / 576p / 720p / 1080i / 1080p
PowerVoltage 100-240 VAC, 50-60 Hz (auto switch)
Display areaFull Scan 550.08 mm (H) x 343.8 mm (V)
21.66 (H) x 13.54 (V)
Operating
conditionsTemperature
Humidity
Altitude32° F to + 95° F (0° C to + 35° C)
10% to 90%  (non-condensing)
To 10,000 feet
Storage
conditionsTemperature
Humidity
Altitude-4° F to + 140° F (-20° C to + 60° C)
10% to 80% (non-condensing)
To 40,000 feet
DimensionsPhysical 595.68 mm (W) x 478.84 mm (H) x 254.67 mm (D)
23.45 (W) x 18.85 (H) x 10.03 (D)
WeightPhysical 16.29 lb (7.39 kg)
RegulationsBSMI, VCCI, CCC, PSB, C-Tick, MIC, CE, GS, Ergo,
Gost-R/Hygienic, Ukraine, TCO03, SASO, UL/cUL, FCC-B,
ICES-B, TUV-S/IRAM/UL-AR S Mark, NOM, E
NERGY STA R®
Power saving
modesOn
Off
						

							ViewSonicVA2626wm 16
Troubleshooting
No power
• Make sure power button (or switch) is ON.
• Make sure A/C power cord is securely connected to the LCD display.
• Plug another electrical device (like a radio) into the power outlet to verify that the outlet is
supplying proper voltage.
Power is ON but no screen image
• Make sure the video cable supplied with the LCD display is tightly secured to the video
output port on the back of the computer. If the other end of the video cable is not attached
permanently to the LCD display, tightly secure it to the LCD display.
• Adjust brightness and contrast.
• If you are using an Macintosh older than G3, you need a Macintosh adapter.
Wrong or abnormal colors
• If any colors (red, green, or blue) are missing, check the video cable to make sure it is
securely connected. Loose or broken pins in the cable connector could cause an improper
connection.
• Connect the LCD display to another computer.
• If you have an older graphics card, contact ViewSonic
® for a non-DDC adapter.
Control buttons do not work
• Press only one button at a time.
 
						

							ViewSonicVA2626wm 17
Customer Support
For technical support or product service, see the table below or contact your reseller.
NOTE: You will need the product serial number.
Country/RegionWebsite T = Telephone
F = FAXEmail
Australia/New Zealand www.viewsonic.com.auAUS= 1800 880 818
NZ= 0800 008 [email protected]
Canada www.viewsonic.comT (Toll-Free)= 1-866-463-4775  
T (Toll)= 1-424-233-2533
F= [email protected]
Europe/Middle East/
Baltic countries/North 
Africawww.viewsoniceurope.com Contact your reseller
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 [email protected]
India www.in.viewsonic.com T= 1800 11 9999 [email protected] 
Korea www.kr.viewsonic.com T= 080 333 2131 [email protected]
Latin America 
(Argentina)www.viewsonic.com/la/ T= 0800 666 0194 [email protected]
Latin America (Brazil) www.viewsonic.com/la/ T= 0800 891 6984 [email protected]
Latin America (Chile) www.viewsonic.com/la/ T= 800 440 303 [email protected]
Latin America 
(Columbia)www.viewsonic.com/la/ T= 01 800 915 6588 [email protected]
Latin America (Mexico) www.viewsonic.com/la/T= 001 800 514 6518 [email protected]
Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS
Electroser, Av Reforma No. 403Gx39 y 41, 97000 Mérida, Yucatán. Tel: 01.999.925.19.16
Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico
Latin America (Peru) www.viewsonic.com/la/ T= 0800 53458 [email protected]
Macau www.hk.viewsonic.com T= 853 700 303 [email protected]
Puerto Rico & Virgin 
Islandswww.viewsonic.comT= 1-800-688-6688 (English)
T= 1-866-379-1304 (Spanish)
F= [email protected]
[email protected]
Singapore/Malaysia/
Thailandwww.ap.viewsonic.com T= 65 6461 6044 [email protected]
South Africa www.viewsoniceurope.com www.viewsoniceurope.com/uk/Support/Calldesk.htm
United Kingdomwww.viewsoniceurope.com
/uk/www.viewsoniceurope.com/uk/Support/Calldesk.htm
United States www.viewsonic.comT (Toll-Free)= 1-800-688-6688   
T (Toll)= 1-424-233-2530
F= [email protected]