ViewSonic VA2213w Manual

ViewSonicVA2213wm 8
Using the LCD Display
Setting the Timing Mode
Setting the timing mode is im portant for maximizing the quali ty of the screen image and
minimizing eye strain. The  timing mode consists of the  resolution (example 1920 x 1080) and
refresh rate  (or vertical frequency; ex ample 60 Hz). After setting the timing mode, use the
OSD (On-screen Display) controls to adjust the screen image.
For the best picture quality set  your LCD display timing mode to:
VESA 1920 x 1080 @ 60Hz .
To set the...

ViewSonicVA2213wm 9
Adjusting the Screen Image
Use the buttons on the front control panel to di splay and adjust the OSD controls which display 
on the screen. The OSD controls are explained at  the top of the next page and are defined in 
“Main Menu Controls” on page 11.
Main Menu
with OSD controls
Front Control Panel
shown below in detail
Scrolls through 
menu options and 
adjusts the 
displayed control.
Increases the 
volume, decreases 
the volume, and 
mutes the audio.
Displays the control screen...

ViewSonicVA2213wm 10
Do the following to ad
just the display setting:
1. To display the Main Menu, press button [1].
NOTE:  All OSD menus and adjustment screens  disappear automatically after about 15 
seconds. This is adjustable through the  OSD timeout setting in the setup menu.
2. To select a control to adjust, press SorT to scroll up or down in the Main Menu.
3. After the desired control is se lected, press button [2]. A cont rol screen like the one shown 
below appears.
4. To adjust the control,...

ViewSonicVA2213wm 11
Main Menu Controls
Adjust the menu items shown below by using the up  S and down  T buttons.
Control Explanation
Auto Image Adjust  automatically sizes, centers, a nd fine tunes the video signal 
to eliminate waviness and distortion. Pr ess the [2] button to obtain a sharper 
image.
NOTE:  Auto Image Adjust works with most common video cards. If this 
function does not work on your LCD display,  then lower the video refresh rate 
to 60 Hz and set the resolution to its pre-set...

ViewSonicVA2213wm 12
Control Explanation
5000K-Adds red to the screen image for warmer white and richer red.
User Color  Individual adjustments for red (R), green (G),  and blue (B).
1. To select color (R, G or B) press button [2].
2. To adjust selected color, press Sand T.
Important:  If you select RECALL from the Main Menu when the product is 
set to a Preset Timing Mode, colors  return to the 6500K factory preset.
Information  displays the timing mode (vid eo signal input) coming from the 
graphics...

ViewSonicVA2213wm 13
Control Explanation
Dynamic Contrast  allows the user to turn the  contrast ratio enhancement on or 
off.
Aspect ratio  Selects the image size for 4:3 and full screen.
ECO Mode  provides the lower power consum ption by reducing the brightness. 
Standard:  The default brightness setting.
Optimize:  Decreases the brightness by 25 %.
Conserve:  Decreases the brightness by 50 %.
Setup Menu  displays the menu shown below:
Language  Select  allows the user to choose th e language used in...

ViewSonicVA2213wm 14
Other Information
Specifications
1 Macintosh computers older than G3 require a ViewSonic® Macintosh adapter. To order an adapter, contact
ViewSonic. LCD
Ty p e
Color Filter
Glass Surface 22” (full 21.5 wide viewable diagonal area),
TFT (Thin Film Transistor), Active Matrix WUXGA LCD,
0.24825 mm pixel pitch
RGB vertical stripe
Anti-Glare
Input Signal Video Sync RGB analog (0.7/1.0 Vp-p, 75 ohms)
Separate Sync
f
h:24-82 kHz, fv:50-75 Hz
Compatibility PC
Macintosh
1Up to 1920 x 1080...

ViewSonicVA2213wm 15
Troubleshooting
No power
• Make sure power button (or switch) is ON.
• Make sure A/C power cord is secu rely connected to the LCD display.
• Plug another electrical device (l ike a radio) into the power outlet to verify that the outlet is
supplying proper voltage.
Power is ON but no screen image • Make sure the video cable supplied with the  LCD display is tightly secured to the video
output port on the back of the computer. If the  other end of the video cable is not attached...

ViewSonicVA2213wm 16
Customer Support
For technical support or product  service, see the table below or contact your reseller.
NOTE:  You will need the product serial number.
Country/RegionWebsite T = Telephone
F = FAXEmail
Australia/New Zealand www.viewsonic.com.au AUS= 1800 880 818
NZ= 0800 008 [email protected]
Canada www.viewsonic.com T (Toll-Free)= 1-866-463-4775  
T (Toll)= 1-424-233-2533
F= [email protected]
Europe/Middle East/
Baltic countries/North 
Africa...

ViewSonicVA2213wm 17
Cleaning the LCD Display
• MAKE SURE THE LCD DISPLAY IS TURNED OFF.
• NEVER SPRAY OR POUR ANY LIQUID DI RECTLY ONTO THE SCREEN OR CASE.
To clean the screen:
1. Wipe the screen with a clean,  soft, lint-free cloth. This removes dust and other particles.
2. If the screen still not  clean, apply a small  amount of non-ammonia
, non-alcohol based glass 
cleaner onto a clean, so ft, lint-free cloth, and wipe the screen.
To clean the case:
1. Use a soft, dry cloth.
2. If the case still...