ViewSonic Projector Pro8600 User Manual

 24
Message Input Password
Password Delete
Green Mode
DC 12V
Quick Power On
Quick Cooling Start up ScreenViewSonic, User
Screen Capture
Screen Capture Delete
-5 - +5
On, Off
Off, CC1, CC2, CC3, CC4, T1, T2
On, Off
On, Off
On, Off
On, Off Others
On, Off
Function*3 Setting
Filter Mode*2
High Altitude
OSD Transparency
Top-Left, Bottom-Left, 
Top-Right, Bottom-Right
Front-Table, Front-Ceiling, 
Rear-Table, Rear-Ceiling
0 - 60
0, 10, 20, 30, 40, 50, 60, 70, 80, 90
Presentation Timer
Timer Period 0 - 240 Min...

 25
*1 Adjustable range and default setting vary depending on signal type.
*2 This function is only available when the projector is installed an optional filter cover.
*3 The selectable Function list includes Brightness, Contrast, Saturation, Color Setting > 
Gamma, Overscan, Noise Reduction, Audio Setting, Microphone Volume, Speaker Volume, 
Mute, Keystone, Aspect Ratio, Projection, Power Saving, ECO Mode, Filter Mode, Menu 
Position, OSD Transparency, Closed Caption, Message, Zoom, DCR and Test...

 26
How to operate
1. Press MENU on the projector or Menu on the remote control to open the OSD menu.
2. When OSD is displayed, use 
/ to select any feature in the main menu.
3. After selecting the desired main menu item, press   to select feature setting.
4. Use / to select the desired item and adjust the settings with /.
5. Press 
MENU on the projector or Menu on the remote control, the screen will return to
the main menu.
6. To exit OSD, press 
MENU on the projector or Menu on the remote control...

 27
horizontal or vertical width.
• 4:3:Scales an image so that it is displayed in the center of the screen with a 4:3 
aspect ratio.
• 16:9:Scales an image so that it is displayed in the center of the screen with a 16:9 
aspect ratio.
• 16:10:Scale an image so that it is displayed in the center of the screen with a 16:10 
aspect ratio.
White Intensity
Increase the brightness of white areas.
Gamma
Effect the represent of dark scenery. With greater gamma value, dark scenery will look 
brighter.
3D Sync...

 28
Allow you to enter the Audio Setting menu.
• Computer 1: Select the audio input for Computer in 1 signal.
• When Audio in 1 is turned on, Audio in 2 and Audio in 3 will turn off 
automatically.
• Computer 2: Select the audio input for Computer in 2 signal.
• When Audio in 2 is turned on, Audio in 1 and Audio in 3 will turn off 
automatically.
• Video Source: Select the audio input for video source.
• When Audio in 3 is turned on, Audio in 1 and Audio in 2 will turn off 
automatically.
• HDMI: Select...

 29
High Altitude
Use this function to allow the fans operates at full speed continuously to achieve proper 
high altitude cooling of the projector.
OSD Timeout
Duration of OSD menu display countly starts (at idle state by second).
OSD Transparency
Select to change the transparency level of the OSD background.
Presentation Timer
Remind the presenter to finish the presentation within a certain time frame.
• Presentation Timer: Set whether to activate the presentation timer.
• Timer Period: Set a preferred...

 30
• DCR (Dynamic Contrast Ratio): Enable DCR will further enhance contrast ratio by 
darkening the black scenes. Disable DCR will resume to normal contrast 
performance. DCR will impact lamp life and system noise performance.
• Message: Enable or disable the message box at the right bottom of the screen.
Function
Allow user to define a short cut key on the remote control, and the function item is selected 
in OSD menu.
Te s t  P a t t e r n
Display embedded test pattern.
Quick Power On
• On: The...

 31
• IP Address: Numerical address to identify networked computers. This function can 
only be used when DHCP is set to Off.
• The IP Address is the number that identifies this projector on the network. You 
cannot have two devices with the same IP Address on the same network.
• The IP Address “0.0.0.0” is prohibited.
• Connection Mode: Methods for connecting to wireless networks with Wi-Fi enabled 
devices.
Network Restart
Restore network settings to default.
The password for web administrator and...

 32
Controlling the projector through a LAN environment
You can manage and control the projector from one or more remote computers when they 
are properly connected to the same local area network.
Wired connection
If you are in a DHCP environment:
1. Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the 
projector and the other end to the RJ45 port on your Ethernet or router.
2. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the Network menu is...

 33
4. Press  to select the item you want to modify and press ENTER on the projector 
or Enter on the remote control.
5. Press  /  to move the cursor and the enter the value.
6. To save the settings, press ENTER on the projector or Enter on the remote 
control. If you do not want to save the settings, press MENU/EXIT on the projector
7. or Menu on the remote control.
8. Press 
 to highlight Apply and press ENTER on the projector or Enter on the 
remote control.
Important
•
If the RJ45 cables are not...