ViewSonic Projector Pro8450w User Manual

							
ViewSonic  Pro8450w 39
4. Press  to select the item you want to modify and press ENTER on the projector 
or Enter on the remote control.
5. Press  /  to move the cursor and the enter the value.
6. To save the settings, press 
ENTER on the projector or Enter on the remote 
control. If you do not want to save the settings, press MENU/EXIT on the projector
7. or Menu on the remote control.
8. Press  to highlight Apply and press ENTER on the projector or Enter on the 
remote control.
Important
„If the RJ45 cables are not properly connected, the IP Address, Subnet Mask, 
Default Gateway, and DNS settings will display 0.0.0.0. Make sure the 
cables are properly connected and perform the procedures above again.
„If you wish to connect to the projector in its standby mode, be sure you have 
selected RJ45 and obtained the IP Address, Subnet Mask, Default Gateway, 
and DNS information when the projector is on. 
						

							
ViewSonic  Pro8450w 40
Wireless connection
To connect to the projector wirelessly, you have to plug a ViewSonic wireless dongle 
(optional) to the USB Type A connector on the projector, and then only a few OSD 
configuration steps are required.
1. Make sure the projector is turned on.
2. Press MENU/EXIT on the projector or Menu on the remote control and then press 
/  until the NetWork menu is highlighted.
3. Highlight Wireless LAN and press ENTER on the projector or Enter on the 
remote control.
4. Make sure the 
Status is Connect.
5. Make sure the SSID information is displayed.
6. Press  to highlight Connection Mode and press  /  to select AP or Infrastructure. In AP mode, you need to use your computer’s wireless 
connection utility to search the projector’s SSID and connect to it. Then you can 
search the projector with pwPresenter. To use 
Infrastructure mode, you should 
connect both your computer and projector to the same AP router and make 
connections with the IP address.
Important
„If you need more information about AP and Infrastructure modes, please 
refer to user documentations for Wireless Routers which are usually 
available on 3C stores.
ViewSonic 
wireless dongle 
						

							
ViewSonic  Pro8450w 41
Controlling the projector through a web browser
Once you have the correct IP address for the projector and the projector is on or in 
standby mode, you can use any computer that is on the same local area network to 
control the projector.
Important
„If you are using Microsoft Internet Explorer, make sure it is version 7.0 or 
higher.
„The screenshots in this manual are for reference only, and may differ from 
the actual design.
1. Enter the address of the projector in the address bar of your browser and press  Enter.
2. The main page of the ViewSonic webpage control system appears.
3. To change the language for the web pages, click the down arrow to reveal a drop  down list and select a desired language.
4. To download pwPresenter, click Download. See  “Displaying images through 
pwPresenter” on page 47  for details.
5. To achieve best performance, download the install mirror display driver.
6. To download USB LAN driver, click Download.
4
5
6
7
8
3 
						

							
ViewSonic  Pro8450w 42
7. To have access to the Admin page, you need to enter a password. The default 
password is “0000”.
„System Status: Displays the system information.
„General Setup: Allows you to change the password for the Admin page.
„Picture Setup/Image Setup: Provides some OSD menu items for adjusting 
the projected pictures.
„Alert Setup/SMTP Mail Setup: Allows you to setup the mail server and send 
system error messages to your ITS administrator.
„Network Setup: Provides wired and wireless network settings.
„Presenter Setup: Allows you to change Admin and User passwords for web 
control.
„Reset to Default: Allows you to restore the device to the factory default 
settings.
„Reboot System: Allows you to reboot the device immediately. 
						

							
ViewSonic  Pro8450w 43
8. The Crestron (eControl) page displays the Crestron eControl user interface. The 
eControl page provides a variety of virtual keys to control the projector or adjust 
the projected pictures.
i. These buttons function the same as the ones on the OSD menus or remote control.
ii. To switch between input signals, click on your desired signal.
iii. To change the language for the Crestron page, click the down arrow to  reveal a drop down list and select a desired language.
Important
„The Menu button can also be used to go back to previous OSD menus, exit 
and save menu settings.
„The source list varies according to the connectors available on the projector.
„When you use the projector control panel or remote control to change the 
OSD menu settings, it may take a while for the web browser to synchronize 
these changes with the projector.
i
i
iii
iii
You can press W/X to reveal 
more buttons. 
						

							
ViewSonic  Pro8450w 44
The tools page allows you to manage the projector, configure the LAN control settings 
and secure access of remote network operation on this projector.
iv. This section is only used with the Crestron Control System. Please contact Creston or refer to its user manual for setup information.
v. Click the down arrow to reveal a drop down list and select a default  language.
vi. You can name the projector, keep track of its location and the person in  charge of it.
vii. You can adjust the LAN Control Settings.
viii. Once set, access to the remote network operation on this projector has  been password-protected.
ix. Once set, access to the tools page has been password-protected.
Important
„To prevent errors, only input the English alphabet and digits on the tools 
page.
„After making the adjustments, press the Send button and the data will be 
saved for the projector.
x. Press  Exit to go back to the remote network operation page.
ivvi
vvii
viii
ix
x 
						

							
ViewSonic  Pro8450w 45
Please pay attention to the limitation of input length (including space and other 
punctuation keys) in the list blow:
Category ItemInput LengthMaximum Number of
Characters
Crestron Control IP Address 15
IP ID 2
Port 5
Projector Projector Name 10
Location 9
Assigned To 9
Network Configuration DHCP (Enabled) (N/A)
IP Address 15
Subnet Mask 15
Default Gateway 15
DNS Server 15
User Password Enabled (N/A) New Password 20
Confirm 2
Admin Password Enabled (N/A) New Password 20
Confirm 20 
						

							
ViewSonic  Pro8450w 46
The info page displays the information and status of this projector.
After pressing the button “Contact IT Help”, the HELP DESK window will appear in the 
upper right corner of the screen. You will  be able to deliver messages to RoomView 
software administrators/users who c onnect to the same local area network.
For more information, visit  http://www.crestron.com & www.crestron.com/getroomview .
Press Exit to go 
back to the 
remote network 
operation page. 
						

							
ViewSonic  Pro8450w 47
Displaying images through pwPresenter
Downloading and in stalling pwPresenter
The pwPresenter is an application running on the host PC. It helps connect your 
computer to an available network projector and transfer the desktop content to the 
network projector via local network connection.
1. Enter the main page of Network Control. See steps 1-2 on page  41 for details.
2. Download pwPresenter.
3. When the download is complete, install  the software to your computer by clicking 
the exe file. Follow the on-screen inst ructions to complete the installation.
4. Launch pwPresenter.
Using pwPresenter
1. The Search page allows you to search and connect to a projector.
i. To connect to a projector, select Directly then type the projector IP address  and click Connect.
ii. To search for projectors, simply click Search to list all the projectors on the 
same local area network. Click the desired projectors in the Search result 
list, and click Connect directly. You can also type a desired projector name 
and click Search.
iii. You can link to the ViewSonic webpage control system on  page 41.
1
2
4&5
6
7
3
i
iii
ii 
						

							
ViewSonic  Pro8450w 48
2. The Capture screen allows you to start or pause capture screen.
3. You can choose a capture mode from here.
i. To display a full screen, click FullScreen.
ii. To display a partial screen, click FixedSize. A square appears on your 
screen. You can place it where you want to project. 
iii. If you wish to change the square, click Alterable.
i
ii
iii