ViewSonic Projector PLED-W600 User Manual

							PLED-W600/PLED-W800
LED Projector
User Guide
IMPORTANT:  Please read this User Guide to obtain important information on installing 
and using your product in a safe manner, as well as registering your product for future 
service. Warranty information contained in this User Guide will describe your limited 
coverage from ViewSonic Corporation, which is also found on our web site at http://www.
viewsonic.com in English, or in specific languages using the Regional selection box in the 
upper right corner of our website. “Antes de operar su equipo lea cu idadosamente las 
instrucciones en este manual”
Model No. VS15897/VS15898 
						

							Thank you for choosing ViewSonic
With over 25 years as a world leading provider of visual solutions, ViewSonic 
is dedicated to exceeding the world’s expectations for technological evolution, 
innovation, and simplicity. At ViewSonic, we believe that our products have the 
potential to make a positive impact in the world, and we are confident that the 
ViewSonic product you have chosen will serve you well. 
Once again, thank you for choosing ViewSonic !  
						

							i
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Operation is subject to \
the following two 
conditions: (1) this device may not cause harmful interference, and (\
2) this device must accept 
any interference received, including interference that may cause undesir\
ed operation.
This equipment has been tested and found to comply with the limits for a\
 Class B digital 
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment generates, 
uses, and can radiate radio frequency energy, and if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications\
. However, there is 
no guarantee that interference will not occur in a particular installati\
on. If this equipment does 
cause harmful interference to radio or television reception, which can b\
e determined by turning 
the equipment off and on, the user is encouraged to try to correct the interference by o\
ne or 
more of the following measures:
 yReorient or relocate the receiving antenna.
 yIncrease the separation between the equipment and receiver.
 yConnect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
 yConsult the dealer or an experienced radio/TV technician for help.
Warning:  You are cautioned that changes or modifications not expressly approved by the 
party responsible for compliance could void your authority to operate th\
e equipment.
Industry Canada Statement
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic Equipment Directive 
2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment including any spent 
or discarded batteries or accumulators as unsorted municipal waste, but \
use the return 
and collection systems available. 
If the batteries, accumulators and button cells included with this equip\
ment, display 
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a \
heavy metal 
content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or mo\
re than 
0.004% Lead.
Compliance Information  
						

							ii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Direc\
tive 2011/65/
EU of the European Parliament and the Council on restriction of the use \
of certain hazardous 
substances in electrical and electronic equipment (RoHS2 Directive) an\
d is deemed to 
comply with the maximum concentration values issued by the European T
 echnical Adaptation 
Committee (TAC) as shown below:
Substance Proposed Maximum
Concentration Actual Concentration
Lead (Pb) 0.1%< 0.1%
Mercury (Hg) 0.1%< 0.1%
Cadmium (Cd) 0.01%< 0.01%
Hexavalent Chromium (Cr 6+
) 0.1%< 0.1%
Polybrominated biphenyls (PBB) 0.1%< 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1%< 0.1%
Certain components of products as stated above are exempted under the  Annex III of the 
RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode fluorescent lamps and external electrode fluorescent lamps 
(CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length ( ＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length ( ＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of fluorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by w\
eight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys c\
ontaining 85% by 
weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceram\
ic other than   
dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a \
glass or ceramic 
matrix compound.
Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India) This product complies with the “India 
E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent chromium, polybrominated 
biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 
0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.  
						

							iii
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance wi\
th the 
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, \
stoves, or other 
devices (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug\
.  A polarized 
plug has two blades with one wider than the other. A grounding type plug has two 
blades and a third grounding prong. The wide blade and the third prong are provided 
for your safety. If the provided plug does not fit into your outlet, consult an electrician 
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at p\
lugs. 
Convenience receptacles and the point where they exit from the unit. Be sure that the 
power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the 
manufacturer, or sold with the unit. When a cart is used, use caution when 
moving the cart/unit combination to avoid injury from tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is  required when the unit 
has been damaged in any way, such as: if the power-supply cord or plug is damaged, 
if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or 
moisture, or if the unit does not operate normally or has been dropped.  
						

							iv
Copyright Information
Copyright © ViewSonic Corporation, 2014. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, and the Windows logo are registered trademarks of Mi\
crosoft 
Corporation in the United States and other countries.
ViewSonic and the three birds logo are registered trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines 
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial erro\
rs or 
omissions contained herein; nor for incidental or consequential damages \
resulting from 
furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right 
to change product specifications without notice. Information in this document may change 
without notice.
No part of this document may be copied, reproduced, or transmitted by an\
y means, for any 
purpose without prior written permission from ViewSonic Corporation.  
						

							v
Product Registration
To fulfill possible future product needs, and to receive additional product informationas it 
becomes available, please visit your region section on ViewSonic’s website to register your 
product online.
The ViewSonic CD also provides an opportunity for you to print the product re\
gistration form. 
Upon completion, please mail or fax to a respective ViewSonic office. To find your registration 
form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer servi\
ce needs.
Please print this user guide and fill the information in the “For Y
 our Records” section.
For additional information, please see the “Customer Support” sect\
ion in this guide.
For Your Records
Product Name: PLED-W600/PLED-W800
ViewSonic LED Projector
Model Number: VS15897/VS15898
Document Number: PLED-W600/PLED-W800_UG_ENG Rev. 1A 08-25-14
Serial Number: ____________________________________
Purchase Date: ____________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you \
and the 
environment. Please use care and dispose of in accordance with local, st\
ate or federal laws.
ViewSonic respects the environment and is committed to working and living\
 green.
Thank you for being part of Smarter, Greener Computing.
Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx  
						

							6
Table of Contents
Viewing System Settings ......................24
USB Display
 .........................................25
Wi-Fi Display
 ........................................26
Configure Wireless Connection   
(via AP  mode)
 .......................................27
Configure Wireless Connection   
(via Client mode)
 ..................................28
Media Streaming
 ..................................29
Screen Mirroring
 ...................................30
Adjust Menu Settings for External Input 
Source
 ..................................................31
Using the Main Menu
 ...........................33
Appendix 35
Media File Support List   
(PLED-W800 only)
 ...............................35
Specifications
 .......................................40
Troubleshooting
 ....................................41
Introduction 7
Package Overview .................................7
Product Overview
 ...................................8
Remote Control
 ......................................9
Installation 10
Power On/Off ........................................10
Adjust Projected Image Height
 .............10
Adjust the Projected Image
 ...................11
Connect Input Source - HDMI/MHL or 
COMPUTER
 .........................................12
Connect Input Source - Composite AV  
IN (PLED-W800 only)
 ...........................13
Insert SD Card (PLED-W800 only)
 .......13
Insert USB Flash Drive  
(PLED-W800 only)
 ...............................14
Mount the Projector
 ..............................14
Using Multimedia Menu   
(PLED-W800 only) 15
How to Use the Multimedia Menu ........15
Viewing Photos
 .....................................17
Photo Settings
 ......................................18
Playing Videos
 ......................................19
Video Settings
 ......................................20
Playing Music
 .......................................21
Music Settings
 ......................................22
Viewing Documents
 ..............................23  
						

							7
Introduction
Package Overview
Unpack and inspect the box contents to ensure all parts listed below are in the box. If 
something is missing, please contact our customer service.
ProjectorAC Power CordAC  Power Adapter
HDMI CableSoft Carrying BagRemote Control (with batteries)
PC System Requirements
Intel®
 Pentium ®
 processor 
or greater running on  
Windows ®
 Platform, 4x 
CD-ROM drive; 64MB or 
more of available RAM; 
800x600 color displa y.
Ma c®
 System Requirements
Mac OS version 10.x; 4x 
CD-ROM drive; 64MB or 
more of available RAM; 
800x600 color displa y.
Copyright  © 2011, ViewSonic  Corporation.  All rights  reserved.  All  trademarks, 
registered  or  otherwise, are the property  of  their respective  companies. 
Disclaimer:  ViewSonic Corporation  shall not be liable  for technical  or editorial r eeors 
or  omissions  contained  herein;  nor  for incidental  or  consequential  damages 
resulting from furnishing this meterial, or the performance or use of th\
is product. 
In  the  interest  of  continuing  product  improvement,  ViewSonic  Corporation 
reserves the right to change product specifications without notice. Info\
rmation in 
this  CD-ROM  may change  without  notice, No  part  of  this  CD-ROM  may be 
copied,  reproduced,  or transmitted by  any means,  for any purpose  without prior 
written permission of Vi ewSonic Corporation.
08/01/1 1 • PLED-W500_UG • Made in China 
PLED-W800 & W600 DLP Projecto rUser Guide and
Installation Software
Quick Start GuideCD-ROM (User’s Guide)
   Due to different applications in each Country, some regions may have different accessories.  Make sure to properly discard the used batteries according to local regu\
lations.  
						

							8
Product Overview
COLORAUDIOMENU/ EXIT
SOURCEPOWER
PLED-W800HDMI/MH L
COMPUTER
SD CARD
AV  IN
A UDI O
OU T US
BHDMI/MH L
SERV ICEPLED-W600AUDIO
OUT
1111
564
121010131414151516
19
98
7
2
3
1
182120
1717
1.   Kensington  Lock
2.  Focus Dial
3. Left Button / Audio - ()
4.
 Power Button () 
5. Down Button / Audio mode ()
6.
  Source Button (SOURCE)
7.
  Right Button / Audio + ()
8.
 Menu Button (MENU) 
9.  Up Button / Color mode ()
10. IR Receiver
11. Audio Output Connector
12. A/V Input Connector
13. SD Card Slot
14. HDMI/MHL Connector
15.  USB Connector
16. COMPUTER Connector
17. Speaker
18. Lens
19. DC Input
20. Screw Hole for Tripod
21. Elevator Foot
 
   Items 3,5, 7~9 are also function buttons. Functions vary depending on th\
e current mode.
PLED-W600
PLED-W800