ViewSonic Projector PJD8653ws User Manual

							30
Auto Screen (12V Out)
Choose “On”, the down/up move of electronic screen will be related\
 with power on/
off of Projector.
Test Pattern
Display a test pattern.
Security
Refer next page.
Reset
Choose “Yes” to return the parameters on all menus to the factory \
default settings.  
						

							31
Setting | Security
Security
 
` On: Choose “On” to use security verification when turning on the projector.
 
` Off: Choose “Off” to be able to switch on the projector without pa\
ssword 
verification.
Change Password
 
` First time:
 
y Press the ► button to set the password.
 
y The password has to be 6 digits.
 
y Use the ▲ or ▼ 
on the remote control to select your new password on the 
screen and then press  ► to confirm it.
 
` Change Password:
 
y Use the ▲ or ▼ 
on the remote control to enter your current password on the 
screen and then press  ► to confirm it.
 
y Enter a new password (6 digits in length) then press 
“Enter” to confirm it.
 
y Enter the new password again and press 
“Enter” to confirm it.
 
` If the incorrect password is entered for 3 times, the projector will aut\
omatically 
shut down.
 
` If you have forgotten your password, please contact your local office for support.
Select
EnterExit
Security
Security
Change Password On  
						

							32
SelectEnterExit
Security
Enter Security Code (6 digits)
Incorrect security code Re-enter again
 
  Password default value is “0000” (first time).  
						

							33
Mute
 
` Choose “On” to turn mute on.
 
` Choose “Off” to turn mute off.
Volume
 
` Press the ◄ button to decrease the volume.
 
` Press the ► button to increase the volume.
Microphone Volume
 
` Press the ◄ button to decrease the microphone Volume.
 
` Press the ► button to increase the microphone Volume.
Volume
VolumeMute
Volume
Microphone Volume Off
Select
EnterExit  
						

							34
Logo
Use this function to set the desired startup screen. If changes are made\
 they will 
take effect the next time the projector is powered on. 
` Default: The default startup screen.
 
` User: Use stored picture from “Logo Capture” function.
Logo Capture
Press ► button to capture an image of the picture currently displayed on screen.
Screen capture in progress...
Please wait...
 
  For successful logo capture, please ensure that the onscreen image does \
not exceed the 
projector’s native resolution. (WXGA:1280x800).
 
  “Logo Capture” is not available when 3D is enabled.
 
  Before active this function, it is recommended that “Aspect Ratio”\
 is set to the “Auto”.
Auto Source
 
` On: The projector will search for other signals if the current input sig\
nal is lost.
 
` Off: The projector will only search current input connection.
Input
Press ► button to enable/disable input sources. The projector will not search for 
inputs that are not selected.
Options
OptionsLogo
Logo Capture
Auto Source
Input
Auto Power Off (min)
Lamp Settings
Dynamic Black
High Altitude
Filters Remind (Hour)
Information Default
On
On
Off
Select
EnterExit  
						

							35
SelectEnterExit
Input
HDMI
VGA-A
VGA-B
S-Video
Composite
Auto Power Off (min)
Sets the countdown timer interval. The countdown timer will start, when \
there is no 
signal being sent to the projector. The projector will automatically pow\
er off when 
the countdown has finished (in minutes).
Lamp Setting
Refer to page 36.
Dynamic Black
 
` On: The pictures with the optimum contrast will be displayed by automati\
cally 
providing aperture compensation and signal compensation to suit the pict\
ures 
concerned.
 
` Off: Turn off this function.
 
  “Dynamic Black” is available when “Color Mode” is set to “\
Movie”.
 
  “Dynamic Black” is not available when “3D” or “Interactiv\
e” is enabled.
 
  When “Dynamic Black” is available, “Lamp Power Mode” selecti\
on is not available.
High Altitude
 
` On: The built-in fans automatically run at a variable speed according to\
 the 
internal temperature.
 
` Off: The built-in fans run at high speed. Select this option when using \
the 
projector at altitudes above 5000 feet/1524 meters or higher.
Filters Remind (Hour)
 
` Filters Remind (Hour): Set the filter reminder time
 
` Cleaning Up Reminder: Select “Yes” to reset the dust filter hour counter after 
replacing or cleaning the dust filter.
Information
Display the projector information for model name, SNID, source, resolution, software 
version, color space and aspect ratio on the screen.  
						

							36
Lamp Hours Used (Normal)
Display the projection time of normal mode.
Lamp Hours Used (ECO)
Display the projection time of ECO mode.
Lamp Life Reminder
 
` On: Choose “On” to show the lamp end of life warning message.
 
` Off: Choose “Off” to hide the lamp end of life warning message.
Lamp Power Mode
 
` Normal: Normal mode.
 
` ECO: Use this function to dim the projector lamp which will lower power \
consumption and extend the lamp life.
Clear Lamp Hours
Choose “Yes” to reset the lamp hour counter after replacing the la\
mp.
Options | Lamp Settings
Select
EnterExit
Lamp Settings
Lamp hours used (Normal)
Lamp hours used (ECO)
Lamp life reminder
Lamp Power Mode
Clear lamp hours Off
Normal  
						

							37
3D
3D
 
` Auto: When a HDMI1.4a 3D timing identification signal is detected, the 3D image 
is selected automatically.
 
` Choose “Off” to disable 3D function.
 
` Choose “On” to enable 3D function.
 
  The 3D display performance will depend on the 3D glasses you applied.
 
  If the input signal is analog, the projector can not automatically identification signal to manually 
switch to the “on”.
 
  When “3D” is enabled, “Color Mode”, “Digital Zoom”, “Color Temp.”, “Dynamic Black” and “Interactive” 
functions are not supported.
3D Invert
If you see a discrete or overlapping image while wearing DLP 3D glasses,\
 you may 
need to execute “Invert” to get best match of left/right image sequence to get the 
correct image.
3D Format
Use this feature to select the 3D format. Options are: “Frame Packing”, “Side-by-Side 
(Half)”, “Top and Bottom”, “Frame Sequential” and  “\
Field Sequential”.
 
  “Frame Sequential” is supported the DLP Link 3D input signals from VGA / HDMI connector.
 
  “Frame Sequential” / “Field Sequential” are supported the HQFS 3D input signals from Composite/S-
video connector.
 
  “Frame Packing” / “Side-by-Side(Half)” / “Top and Bottom” are supported from HDMI 1.4a 3D input 
signals.
1080p @24
Use this feature to select 96 or 144Hz refresh rate as using 3D glasses \
in the1080p @ 
24 frame packing.
3D3D
3D Invert
3D Format
1080p@24 Off
Off
Select
EnterExit  
						

							38
 
  The Interactive function is available when displaying graphic source fro\
m HDMI/VGA input. Other sources 
are not supported.
 
  If “3D” function is enabling, “Interactive” feature is disab\
ling. 
Interactive Settings
Use this feature to select the Interactive Pen function. Options are: “\
Off” and “IR 
Camera”. Choose “Off” to disable the Interactive Pen function.
You need to unplug the Mini USB cable that connects NB/desktop with the \
projector 
before using the Interactive function. After you complete the Interactiv\
e Settings in 
OSD, use Mini USB cable to connect NB/desktop with the projector.
The IR camera Interactive function needs an external IR camera. Please refer to 
below figure and plug in IR camera to projector before projector was installed.
Interactive
InteractiveInteractive Settings
PB Setting Off
Select
EnterExit  
						

							39
LAN
LAN Settings
LAN SettingsDHCP
IP Address
Subnet Mask
Gateway
DNS
Store
Reset Off
Select
Enter Exit
 
` DHCP: If a DHCP server exists in the network to which the projector is 
connected, the IP address will automatically be acquired when you select\
 DHCP 
On. If DHCP is Off, manually set the IP Address, Subnet Mask, and Gatewa\
y. 
Use ▲ or ▼ to select the number of IP address, Subnet Mask, and Gateway. 
 
` IP Address: Select an IP address.
 
` Subnet Mask: Configure the Subnet Mask of the LAN connection.
 
` Gateway: Check the Gateway address with your network/system administrato\
r if 
you configure it manually.
 
` DNS: Check the DNS Server IP address with your network/system administra\
tor 
if you configure it manually.
 
` Store: Choose “Yes” to save the changes made in network configuration 
settings.
 
` Reset: Choose “Yes” to return the display parameters on all menus \
to the factory 
default settings.
LANLAN Settings
Wireless Settings
Select
EnterExit