ViewSonic Projector PJD8353s User Manual

							40
Timer
Timer Period
Select timer period from 1 to 240 min.
Timer Display
Select timer display from 1 min, 2 min, 3 min, Never or Always.
Timer Position
Select timer position from Top Left, Top Right, Bottom  Left or Bottom R\
ight.
Timer Counting Direction
Set the count down or count up timer interval.
Start Counting
Turn on/off the Presentation timer.
Presentation TimerTimer Period
Timer Display
Timer Position
Timer counting direction
Start Counting 1 min
Bottom Right
Count Down
Select
Enter Exit  
						

							41
1. Turn on DHCP to allow a DHCP server to automatically assign an IP, or 
manually enter the required network information.
LAN Settings
DHCP
IP Address
Subnet Mask
Gateway
DNS
Store
Reset Off
Select
Enter Exit
2. Open your web browser and type in IP Address from the OSD LAN. 
3.  Based on network web-page for the input-string in [tools] tab, the limit\
ation for 
Input-Length is in the below list (“space” and the other punctuat\
ion key included): 
Category ItemInput-Length 
 
(characters)
Projector Projector Name
21
Location 21
Administrator 21
Admin Password New Password
4
Confirm 4
Web Management
 
  Use Internet Explorer 5.0 and above or Firefox 1.5 and above and enter t\
he IP address. You can now ac -
cess Web Management and manage the projector from a remote location.  
						

							42
When making a direct connection from your computer to the projector
Step 1: Find an IP Address (192.168.10.100) from LAN function of projector.
Step 2: To open Network Connections, 
click Start, click Control Panel , 
click Network and Internet 
Connections, and then click 
Network Connections. Click the 
connection you want to configure, 
and then, under  Network Tasks 
 , click Change settings of this 
connection .
Step 3: On the General tab, under This  connection uses the following 
items, click Internet Protocol (TCP/
IP), and then click “ Properties.”
Step 4: Click Use the following IP 
address, and type in as below:
 
` IP address: 192.168.10.100
 
` Subnet mask: 255.255.255.0
Step 5: 
To open Internet Options, 
click IE web browser, click Internet 
Options, click the Connections tab  
and click “ LAN Settings...” 
Step 6: The  Local Area Network (LAN) 
Setting dialog box appears , In the 
Proxy Server area , cancel the Use 
a proxy server for your LAN check 
box., then click “ OK” button twice.
Step 7: Open your IE and type in the IP 
address of 192.168.10.100 in the 
URL then press “ Enter” key.           
						

							43
Web Management
Projector Information
LAN Setting
Projector Status and Control
E-mail Setting
Security Setting
Firmware UpdateLAN Settings
Model Name:
Projector Name:
Location:
Administrator:
Save
DHCP
PJD8653wsD21211
Manual
IP Address
Subnet Mask
Gateway
DNS Server
Save
IP Address
Device ID
Port
Save
Crestron Control System Device
Projector Information Page
 
` Projector Information page by entering the projector’s IP address at \
the web 
browser. See “LAN Settings” section.
 
` Language: Allows you to set the language for web management.
LAN Settings Page
 
` Set up the Projector Name, Location and Administrator information (up t\
o 21 
characters for each field). Press Save to store the settings.
 
` Choose DHCP to assign an IP address to the projector from a DHCP server \
automatically, or Manual to assign an IP address manually.
 
` Set up the IP Address, Device ID and Port information on the Crestron fu\
nction.
Web Management
Projector Information
LAN Setting
Projector Status and Control
E-mail Setting
Security Setting
Firmware UpdateProjector Information
Model Name:
Projector Name:
Location:
Administrator:
Status:
Lamp Hours:
Operation Hours:
IP Address:
MAC Address:
Admin Password: PJD8653ws
D21211
Lamp ON
1 hr.
2hr.
192.168.0.100
00:60:E9:0B:52:DB
Not Set!
SubmitLanguage
English  
						

							44
Projector Status and Control Page
 
` Projector Status: There are 4 status: Standby, Warning up, Lamp On, Powe\
r 
Saving and Cooling. Click the Refresh button to refresh the status and c\
ontrol 
settings. 
 
` Auto Power Off: Auto Power Off can be set to Off(0) or 1~120 minutes. \
See “Auto 
Power Off (min)” function.
 
` Alert Status: There are three error status: Lamp warning, Low lamp life,\
 and 
Temperature warning. Your projector might lock up in protection mode if \
any of 
the alerts is activated. To exit protection mode, click the Clear to clear the Alert 
Status before you could Power ON your projector.
 
` Ceiling Mount: Allows you to select the projector mode, depending on how\
 the 
projector is mounted. There are four projection modes: Front, Front Ceil\
ing, Rear 
and Rear Ceiling.See “Ceiling Mount” function.
 
` Source Select: The Source Select menu allows you to select your projecto\
r's 
input source. You can select VGA-A, VGA-B, S-Video, Composite Video and \
 
HDMI.
 
` Color Mode: Select a mode to optimize the display image based on how the\
 
projector is being used. See “Color Mode” function.
 
` Blank Screen: Select On/Off to hide/unhide the 
screen picture.
 
` Aspect Ratio: Allows you to select the aspect ratio to adjust how the im\
age 
appears.
 
` Brightness: Select value to adjust the brightness of the image.
 
` Contrast: Select value to adjust the display contrast.
 
` Volume: Select the value (0~32) for the audio volume
 
` Mute: Choose “On” to turn mute on. Choose “Off” to turn mute\
 off.
 
` Microphone Volume: Select the value (0~32) for the Microphone Volume.
 
  Click the Auto Adjust button to adjust the settings automatically.
 
  Click the Factory Reset button to restore the factory default settings.  
						

							45
Web Management
Projector Information
LAN Setting
Projector Status and Control
E-mail Setting
Security Setting
Firmware UpdateSecurity Setting
Password
New Password
Confirm PasswordSubmitAdministratorSubmitEnableDisable
Please set your password if you enable this feature for first-time. If password 
is set, you will require to enter with your password upon you connect to\
 the 
Web Management.
E-mail Setting Page
 
` E-mail Alert: You can set whether to be notified by email (Enable) or not (Disable).
 
` To/Cc/From: You can enter email address of sender (From) and recipient\
s (To/
Cc) to receive notification when an abnormality or warning occurs.
 
` Out going SMTP server, User name, and Password should be provided by you\
r 
network administrator or MIS.
 
` Alert Condition: You can select the abnormalities or warnings to be notified 
by email. When any of the alert conditions occur, an email will be sent \
to the 
recipients (To/Cc).
 
  Click the Save button to the save settings.
Security Setting Page
 
` Password: Set up an administrator password to access the Web Management.\
 
When enabling password for the first time, set the password before enabling 
it. When the password function is enabled, the administrator password wi\
ll be 
required for accessing the Web Management.
 
` New Password: Enter new password.
 
` Confirm Password: Enter password again and submit.
 
  Contact Service Center if you forget your administrator password.
Web Management
Projector Information
LAN Setting
Projector Status and Control
E-mail Setting
Security Setting
Firmware UpdateE-mail Setting
TO
CC
From
Subject Enable
Alert
Disable
Out going SMTP server
User name
Password
Save
Lamp warning
Lamp life reminder
Temperature warningAlert Condition E-mail Alert
@@@
SMTP Setting 
Submit 
E-mail Alert Test  
						

							46
Web Management
Projector Information
LAN Setting
Projector Status and Control
E-mail Setting
Security Setting
Firmware Update
Network Firmware Version: Gen_v0.62
Update
Firmware UpdateFirmware update will take about a minute. Do not interrupt the process 
once it has begun. Keep the connection established until completion 
of process. The network system will auto reboot and you can re-login after update is complete. 
Cancel
Login Page
 
` Administrator Password: Enter the Administrator Password and click Login\
 
button.
Firmware Update Page
 
` Use the Firmware Update page to update your projector’s firmware. Press 
Update button to start.
1. 
Please wait till the count reaches 0.
Web Management
Projector Information
LAN SettingPlease wait for 3 seconds.
2. Wait for 3 seconds and it will proceed to the next step automatically.
Web Management
Projector Information
LAN SettingPlease wait for 3 seconds.
Continue
Welcome to Web Management.
Projector Name:
IP Address:
Administrator Password:LoginProjector InformationD21211
192.168.0.100
Web Management 
Waiting 1  
						

							47
3. Select the file to upgrade and click the Upgrade button. When upgrading is in 
progress, the Cancel button is disabled.
Upgrade must NOT be interrupted !
(Upgrading firmware may take 60 seconds)
UpgradeCancel
Please select a file (~.bin) to upgrade: Browse...
Upgrade Firmware
4. 
When upgrade is complete, please click the Re Login button to go back to\
 
the Web Management page.
Please wait.
Click on button to proceed after 8 seconds.
Re Login
Crestron
 
` For more information, please visit http://www.crestron.com & www.crestro\
n.com/
getroomview/  
						

							48
Troubleshooting
Appendices
If you experience a problem with your projector, please refer to the follow-
ing information. If a problem persists, please contact your local resell\
er or 
service center.
Image Problems
   No image appears on-screen
 
` Ensure all the cables and power connections are correctly and securely 
connected as described in the “Installation” section.
 
` Ensure the pins of connectors are not crooked or broken.
 
` Check if the projection lamp has been securely installed.
 
` Ensure that the “Blank” feature is not turned on.
  
Partial, scrolling or incorrectly displayed image
 
` Press “Auto Sync” on the remote control.
 
yIf you are using a PC:
 
- For Windows 95, 98, 2000, XP, Windows 7:
1. Open the “My Computer” icon, the “Control Panel” folder, and\
 
then double click on the “Display” icon.
2.  Select the “Settings” tab.
3.  Verify that your display resolution setting is lower than or equal to 
1080p.
4.  Click on the “Advanced Properties”.
 
- For Windows Vista:
1. From the “My Computer” icon, open the “Control Panel” folder\
, 
and double click the “Appearance and Personalization”
2.  Select “Personalization”.
3.  Click “Adjust screen resolution” to display “Display Settings”\
. 
Click on the “Advanced Settings”.  
						

							49
 
- If the projector is still not projecting the whole image, you will also \
need to change the monitor display you are using. Refer to the 
following steps.
1. Select the “Change” under the “Monitor” tab.
2.  Click on “Show all devices”. Next, select “Standard monitor types” 
under the SP box; choose the resolution mode you need under 
the “Models” box.
3.  Verify that the resolution setting of the monitor display is lower 
than or equal to 1080p.
 
yIf you are using a Notebook:
 
- First, follow the steps above to adjust resolution of the computer.
 
- Press the toggle output settings. example: [Fn]+[F4] 
Notebook Brand Function  Keys
Acer [Fn]+[F5]
Asus [Fn]+[F8]
Dell [Fn]+[F8]
Gateway [Fn]+[F4]
IBM/Lenovo [Fn]+[F7]
HP/Compaq [Fn]+[F4]
NEC [Fn]+[F3]
Toshiba [Fn]+[F5]
Mac Apple System Preference -> Display -> 
Arrangement -> Mirror display
 
yIf you experience difficulty changing resolutions or your monitor freezes, 
restart all equipment including the projector.
   The screen of the Notebook or PowerBook computer is not displaying 
your presentation
Some Notebook PCs may deactivate their own screens when a second display\
 
device is in use. Each has a different way to be reactivated. Refer to y\
our com -
puter’s documentation for detailed information.
   Image is unstable or flickering
 
` Adjust the “Phase” to correct it. Refer to the “Screen” sect\
ion for more 
information.
 
` Change the monitor color setting from your computer.