ViewSonic Projector PJD7828HDL User Manual

							6
Projector exterior view
1. External control panel
(See Projector on page 7 for 
details.)
2. Lamp cover
3. Vent (heated air exhaust)
4. Front IR remote sensor
5. Adjuster foot
6. Lens shift wheel
7. Focus and Zoom rings
8. HDMI/MHL-2 port
9. Micro-USB cable
10. Projection lens
11. Audio signal output socket
12. Audio signal input socket 2/
Microphone
13. Audio signal input socket 1
14. S-Video input socket
15. Video input socket
16. USB port-1 (5V/2A out)
17. HDMI-1 port
18. RGB signal output socket
19. RGB (PC)/Component video 
(YPbPr/YCbCr) signal input socket
20. Mini USB port
21. RS-232 control port
22. AC power cord inlet
23. Security bar for anti-theft lock slot
Warning
• THIS APPARATUS MUST BE EARTHED.
• When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring, 
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should 
occur during operation of the unit, operate the disconnect device to switch the power supply 
off, or disconnect the power plug.
1
2
3
4
5
7
8
6 
10
PJD7836HDL
PJD7828HDL/PJD7831HDL
9
8
10
9
7 1
2
3
4
5
Front/upper side
22
23
17202115161412 11131819
Rear/lower side 
						

							7
Controls and functions
Projector
1. Focus ring
Adjusts the focus of the projected image.
2. Zoom ring
Adjusts the size of the projected image.
3. Lens shift wheel
Shifts the projection lens vertically.
4. Menu
Turns on the On-Screen Display (OSD) 
menu. 
Exit
Goes back to previous OSD menu, exits 
and saves menu settings.
5. / / /  (Keystone keys)
Manually corrects distorted images 
resulting from an angled projection.
Left/Right/Up/Down
Selects the desired menu items and makes 
adjustments.
6. Power
Toggles the projector between standby 
mode and Power ON.7. Source
Displays the source selection bar.
 (Help)
Displays the HELP menu by a long press 
for 3 seconds.
8. Enter
Enacts the selected On-Screen Display 
(OSD) menu item.
Displays the Corner Adj. page. 
(PJD7831HDL/PJD
36HDL only)
9.  (My Button)
Allows user to define a short cut key on 
this button, and the function item is 
selected in OSD menu.
10.  (Power indicator light)
Lights up or flashes when the projector is 
under operation.
11.  (Temperature indicator light)
Lights up red if the projectors 
temperature becomes too high.
PJD7836HDL
PJD7836HDLPJD7828HDL/PJD7831HDL
PJD7828HDL
PJD7831HDL
1
2
3
5554
76513
9
1110
12
8
5554
76513
9
1110
12
8
4
7613 14
9
1110
12 14 15 16
8
1
2 
						

							8
12.  (Lamp indicator light)
Indicates the status of the lamp. Lights up 
or flashes when the lamp has developed a 
problem.
13. Color Mode
Selects an available picture setup mode.
14. /  (Keystone keys)
Manually corrects distorted images 
resulting from an angled projection.
15. Left
Selects the desired menu items and makes 
adjustments.
Blank
Hides the screen picture.16. Right
Selects the desired menu items and makes 
adjustments.
 (Panel Key Lock)
Activates panel key lock. To unlock the 
panel keys, long press for 3 seconds on 
. 
						

							9
Remote control
To use the remote mouse control keys 
(Page Up, Page Down,  , and
 ), see 
Using the remote mouse control on 
page 11 for details.
1. Power
Toggles the projector between standby 
mode and Power ON.
2. Source selection keys 
•COMP
Selects D-Sub / Comp. source for 
display.
•VIDEO
Selects Video source for display.
•HDMI/MHL
Selects HDMI/MHL source for 
display.
3. Auto Sync
Automatically determines the best 
picture timings for the displayed 
image.4. / / /  (Keystone keys)
Manually corrects distorted images 
resulting from an angled projection.
Left/Right/Up/Down
Selects the desired menu items and 
makes adjustments.
5. Enter
Enacts the selected On-Screen Display 
(OSD) menu item.
Displays the Corner Adj. page. 
(PJD7828HDL/PJD36HDL only)
6. Menu
Turns on the On-Screen Display 
(OSD) menu.
7.  (Left mouse button)
Performs the same function as the left 
mouse button when the mouse mode is 
activated.
Only available when a PC input signal 
is selected.
COMP VIDEO
Source
PgUp
MousePattern BlankPgDn
Eco
ModeColor
Mode Audio
Mode
Auto
Sync
Menu Exit
Enter
1
2
6
7
3
4
15
16
18
21
22
14
17
19
20
25
23
26
24
5
8
12
9
13
10
11
4
44
HDMI
/MHL 
						

							10 Operating the LASER pointer
The Laser Pointer is a presentation aid for professionals. It emits colored light when you 
press it. The laser beam is visible. It is necessary to press and hold Laser for continuous 
output.
Do not look into the laser light window or shine the laser light beam on yourself or others. See 
the warning messages on the back of the remote control prior to using it.
The laser pointer is not a toy. Parents should be mindful of the dangers of laser energy and 
keep this remote control out of the reach of children.
Remote control code
The projector can be assigned to 8 different remote control codes, 1 to 8. When several 
adjacent projectors are in operation at the same time, switching the remote control codes  8.  (Right mouse button)
Performs the same function as the right 
mouse button when the mouse mode is 
activated.
Only available when a PC input signal is 
selected.
9. Mouse
Switches between the normal and mouse 
modes.
PgUp, PgDn,  ,  : active after pressing 
Mouse. An icon appears on the screen to 
indicate the activation of the mouse mode. 
Only available when a PC input signal is 
selected.
10.  (Panel Key Lock)
Activates panel key lock. To unlock the 
panel keys, press  .
11.  (Presentation Timer)
Displays the presentation timer settings 
menu.
12.  (Volume)
Displays the volume adjustment bar. 
13. Eco Mode
Selects a lamp mode.
14. LED indicator
15.  (My Button)
Allows user to define a short cut key on the 
remote control, and the function item is 
selected in OSD menu.
16. Source
Displays the source selection bar.17. Laser
Emits visible laser pointer light for 
presentation purposes.
18. Exit
Goes back to previous OSD menu, exits 
and saves menu settings.
19. PgUp (Page Up)/PgDn (Page Down)
Operates your display software program 
(on a connected PC) which responds to 
page up/down commands (like Microsoft 
PowerPoint) when the mouse mode is 
activated.
Only available when a PC input signal is 
selected.
20. Pattern
Displays embedded test pattern.
21. Blank
Hides the screen picture.
22.  (Help)
Displays the HELP menu.
23.  (Mute)
Toggles the projector audio between on 
and off.
24.  (Zoom)
Displays the zoom bar that magnifies or 
reduces the projected picture size.
25. Color Mode
Selects an available picture setup mode.
26. Audio Mode
Selects an audio mode. 
						

							11
can prevent interference from other remote controls. Set the remote control code for the 
projector first before changing that for the remote control.
To switch the code for the projector, select from among 1 to 8 in the SYSTEM SETTING: 
ADVANCED > Remote Control Code menu.
To switch the code for the remote control, press ID set and 
the number button corresponding to the remote control code 
set in the projector OSD together for 5 seconds or more. 
The initial code is set to 1. When the code is switched to 8, 
the remote control can control every projector.
If different codes are set on the projector and remote control, 
there will be no response from the remote control. When that 
happens, a messgae will display to remind you to switch the 
code for the remote control.
Using the remote mouse control
The capability of operating your computer with the remote control gives you more 
flexibility when delivering presentations. 
1. Take a USB cable and connect one end to the the Mini USB port on the projector and 
other end to your PC or notebook prior to using the remote control in place of your 
computer’s mouse. See Connecting a computer on page 18 for details.
2. Set the input signal to D-Sub / Comp..
3. Press Mouse on the remote control to switch from the normal mode to the mouse 
mode. An icon appears on the screen to indicate the activation of the mouse mode.
4. Perform the desired mouse controls on your remote control.
• To move the cursor on the screen, press  / / / . 
• To left-click, press  . 
• To right-click, press  . 
• To operate your display software program (on a connected PC) which responds to 
page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.
• To return to the normal mode, press Mouse again or other keys except for the 
mouse related multi-function keys.
Remote control effective range
The Infra-Red (IR) remote control is located on the front 
of the projector. The remote control must be held at an 
angle within 30 degrees perpendicular to the projectors 
IR remote control sensor to function correctly. The 
distance between the remote control and the sensor should 
not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the remote 
control and the IR sensor on the projector that might 
obstruct the infra-red beam.
COMP VIDEO
Source
PgUp
Mouse Pattern BlankPgDn
Eco
ModeColor
Mode Audio
Mode
Auto
Sync
Menu Exit
Enter
Eco
ModeColor
Mode Audio
Mode
HDMI
/MHL
Remote Control Setting
Remote Control Code
A
pprox
. 
30° 
						

							12
Replacing the remote control batteries
1. To open the battery cover, turn the remote control over to view its back, press on the 
finger grip on the cover and pull it up in the direction of the arrow as illustrated.
2. Remove any existing batteries (if necessary) and install two AAA batteries observing 
the battery polarities as indicated in the base of the battery compartment. Positive (+) 
goes to positive and negative (-) goes to negative.
3. Refit the cover by aligning it with the base and pushing it back down into position. 
Stop when it clicks into place.
WARNING
• Avoid leaving the remote control and batteries in an excessive heat or humid environment 
like the kitchen, bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturers instructions and local 
environment regulations for your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are drained or if you will not be using the remote control for an extended 
period of time, remove the batteries to avoid damage to the remote control from possible 
battery leakage. 
						

							13
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select. 
Take into consideration the size and position of your screen, the location of a suitable power 
outlet, as well as the location and distance between the projector and the rest of your 
equipment.
Your projector is designed to be installed in one of the following 4 possible installation 
locations:
1. Front Table
Select this location with the projector placed near 
the floor in front of the screen. This is the most 
common way to position the projector for quick 
setup and portability.
2. Front Ceiling
Select this location with the projector suspended 
upside-down from the ceiling in front of the screen.
Purchase the projector ceiling mount kit from your 
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM SETTING: 
BASIC > Projector Position menu after you turn 
the projector on.
3. Rear Ceiling
Select this location with the projector suspended 
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the 
projector ceiling mounting kit are required for this 
installation location.
Set Rear Ceiling in the SYSTEM SETTING: 
BASIC > Projector Position menu after you turn 
the projector on.
4. Rear Table
Select this location with the projector placed near 
the floor behind the screen.
Note that a special rear projection screen is 
required.
Set Rear Table in the SYSTEM SETTING: 
BASIC > Projector Position menu after you turn 
the projector on. 
						

							14
Projection dimensions
The screen mentioned below refers to the projection screen usually consisting of a screen 
surface and a support structure. 
(a)
(c)
(b)(e)
(f)
(d)
(a)
(c)(b)
(e)(f)
(d)
(a)
(c)
(b)(e)
(f)
(d)
(f): Center of lens (e): Screen
• 16:9 image on a 16:9 screen
• 16:9 image on a 4:3 screen
(a)
(d)
(c)(b)
(e)(f)
PJD7828HDL/PJD7831HDL
(a) Screen 
Size
[inch (m)]16:9 image on a 16:9 Screen 16:9 image on a 4:3 Screen
(b) Projection 
distance [m (inch)](c) Image 
height
[cm (inch)](d) Vertical 
offset
[cm (inch)] (b) Projection 
distance [m (inch)](c) Image 
height
[cm 
(inch)](d) 
Ve r t i c a l  
offset
[cm (inch)] min. max. min. max.
30(0.8) 0.8 (30) 1.0 (39) 37 (15) 1.9 (0.7) 0.7 (28) 0.9 (36) 34 (14) 1.7 (0.7)
40(1.0) 1.0 (40) 1.3 (52) 50 (20) 2.5 (1.0) 0.9 (37) 1.2 (48) 46 (18) 2.3 (0.9)
50(1.3) 1.3 (50) 1.7 (65) 62 (25) 3.1 (1.2) 1.2 (46) 1.5 (60) 57 (23) 2.9 (1.1)
60(1.5) 1.5 (60) 2.0 (79) 75 (29) 3.7 (1.5) 1.4 (55) 1.8 (72) 69 (27) 3.4 (1.4)
70(1.8) 1.8 (70) 2.3 (92) 87 (34) 4.4 (1.7) 1.6 (65) 2.1 (84) 80 (32) 4.0 (1.6)
80(2.0) 2.0 (81) 2.7 (105) 100 (39) 5.0 (2.0) 1.9 (74) 2.4 (96) 91 (36) 4.6 (1.8)
90(2.3) 2.3 (91) 3.0 (118) 112 (44) 5.6 (2.2) 2.1 (83) 2.7 (108) 103 (41) 5.1 (2.0)
100(2.5) 2.6 (101) 3.3 (131) 125 (49) 6.2 (2.5) 2.3 (92) 3.1 (120) 114 (45) 5.7 (2.3)
120(3.0) 3.1 (121) 4.0 (157) 149 (59) 7.5 (2.9) 2.8 (111) 3.7 (144) 137 (54) 6.9 (2.7)
150(3.8) 3.8 (151) 5.0 (196) 187 (74) 9.3 (3.7) 3.5 (139) 4.6 (180) 171 (68) 8.6 (3.4)
200(5.1) 5.1 (201) 6.7 (262) 249 (98) 12.5 (4.9) 4.7 (185) 6.1 (240) 229 (90) 11.4 (4.5)
250(6.4) 6.4 (252) 8.3 (327) 311 (123) 15.6 (6.1) 5.9 (231) 7.6 (300) 286 (113) 14.3 (5.6)
300(7.6) 7.7 (302) 10.0 (393) 374 (147) 18.7 (7.4) 7.0 (277) 9.2 (360) 343 (135) 17.1 (6.8) 
						

							15
There is 3% tolerance among these numbers due to optical component variations. It is 
recommended that if you intend to permanently install the projector, you should physically 
test the projection size and distance using the actual projector in situ before you permanently 
install it, so as to make allowance for this projectors optical characteristics. This will help you 
determine the exact mounting position so that it best suits your installation location.
PJD36HD,
(a) Screen Size
[inch (m)]16:9 image on a 16:9 Screen
(b) Projection distance [m (inch)]
(c) Image height
[cm (inch)](d) Vertical offset
[cm (inch)]
min. max. min. max.
30(0.8) 0.8 (30) 1.0 (39) 37 (15) 1.9 (0.7) 5.6  (2.2)
40(1.0) 1.0 (40) 1.3 (52) 50 (20) 2.5 (1.0) 7.5 (2.9)
50(1.3) 1.3 (50) 1.7 (65) 62 (25) 3.1 (1.2) 9.3  (3.7)
60(1.5) 1.5 (60) 2.0 (79) 75 (29) 3.7 (1.5) 11.2 (4.4)
70(1.8) 1.8 (70) 2.3 (92) 87 (34) 4.4 (1.7) 13.1 (5.1)
80(2.0) 2.0 (81) 2.7 (105) 100 (39) 5.0 (2.0) 14.9 (5.9)
90(2.3) 2.3 (91) 3.0 (118) 112 (44) 5.6 (2.2) 16.8 (6.6)
100(2.5) 2.6 (101) 3.3 (131) 125 (49) 6.2 (2.5) 18.7 (7.4)
120(3.0) 3.1 (121) 4.0 (157) 149 (59) 7.5 (2.9) 22.4 (8.8)
150(3.8) 3.8 (151) 5.0 (196) 187 (74) 9.3 (3.7) 28.0 (11.0)
200(5.1) 5.1 (201) 6.7 (262) 249 (98) 12.5 (4.9) 37.4 (14.7)
250(6.4) 6.4 (252) 8.3 (327) 311 (123) 15.6 (6.1) 46.7 (18.4)
300(7.6) 7.7 (302) 10.0 (393) 374 (147) 18.7 (7.4) 56.0 (22.1)
(a) Screen Size
[inch (m)]16:9 image on a 4:3 Screen
 (b) Projection distance [m (inch)]
(c) Image height
[cm (inch)](d) Vertical offset
[cm (inch)]
min. max. min. max.
30(0.8) 0.7 (28) 0.9 (36) 34 (14) 1.7 (0.7) 5.1  (2.0)
40(1.0) 0.9 (37) 1.2 (48) 46 (18) 2.3 (0.9) 6.9 (2.7)
50(1.3) 1.2 (46) 1.5 (60) 57 (23) 2.9 (1.1) 8.6 (3.4)
60(1.5) 1.4 (55) 1.8 (72) 69 (27) 3.4 (1.4) 10.3 (4.1)
70(1.8) 1.6 (65) 2.1 (84) 80 (32) 4.0 (1.6) 12.0 (4.7)
80(2.0) 1.9 (74) 2.4 (96) 91 (36) 4.6 (1.8) 13.7 (5.4)
90(2.3) 2.1 (83) 2.7 (108) 103 (41) 5.1 (2.0) 15.4 (6.1)
100(2.5) 2.3 (92) 3.1 (120) 114 (45) 5.7 (2.3) 17.1 (6.8)
120(3.0) 2.8 (111) 3.7 (144) 137 (54) 6.9 (2.7) 20.6 (8.1)
150(3.8) 3.5 (139) 4.6 (180) 171 (68) 8.6 (3.4) 25.7 (10.1)
200(5.1) 4.7 (185) 6.1 (240) 229 (90) 11.4 (4.5) 34.3 (13.5)
250(6.4) 5.9 (231) 7.6 (300) 286 (113) 14.3 (5.6) 42.9 (16.9)
300(7.6) 7.0 (277) 9.2 (360) 343 (135) 17.1 (6.8) 51.4 (20.3)